Tag: 642-812
Welcome to download the newest Examwind 700-505 dumps:
Flydumps offers the first-hand Cisco 642-812 exam real questions and answers, by train the latest Cisco 642-812 PDF and VCE dumps,you will well prepare for the Cisco 642-812 exam. Visit Flydumps.com to get free new version for training.
QUESTION 156
Given the following configuration on a switch interface, what happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port? switchport mode access switchport port-security switchport port-security maximum 2 switchport port-security mac-address 0002.0002.0002 switchport port-security violation shutdown
A. The port will shut down.
B. The host will be allowed to connect. TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
C. The host will be refused access.
D. The host can only connect through a hub/switch where 0002.0002.0002 is already connected.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 157
In the use of 802.1X access control, which three protocols are allowed through the switch port before authentication takes place? (Choose three.)
A. STP
B. CDP
C. EAP MD5
D. TACACS+
E. EAP-over-LAN
F. protocols not filtered by an ACL
Correct Answer: ABE Section: (none) Explanation
Explanation/Reference:
QUESTION 158
When you issue a command show port 3/1 on an Ethernet port, you observe the Giants column has a non-zero entry. What could cause this?
A. IEEE 802.1Q
B. IEEE 802.10
C. misconfigured NIC
D. user configuration
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 159
Which VTP information does a Catalyst switch advertise on its trunk ports when using VTP? (Choose two.)
A. VTP mode
B. STP root status
C. negotiation status
D. management domain
E. configuration revision number
Correct Answer: DE Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 160
What are two benefits provided in VTP Version 2 but NOT in VTP Version 1? (Choose two.)
A. supports Token Ring VLANs
B. allows VLAN consistency checks
C. saves VLAN configuration memory
D. reduces the amount of configuration necessary
E. allows active redundant links when used with spanning tree
Correct Answer: AB Section: (none) Explanation
Explanation/Reference:
QUESTION 161
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network, Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit, which two statements are true? (Choose two.)
A. Changing the bridge priority of S1 to 4096 would improve network performance.
B. Changing the bridge priority of S1 to 36864 would improve network performance.
C. Changing the bridge priority of S2 to 36864 would improve network performance.
D. Changing the bridge priority of S3 to 4096 would improve network performance. TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
E. Disabling the Spanning Tree Protocol would improve network performance.
F. Upgrading the link between S2 and S3 to Gigabit Ethernet would improve performance.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 162
Refer to the exhibit. PCs in VLAN 2 are not able to communicate with PCs in VLAN 3. What could be
the cause?
A. IP routing is not enabled.
B. VTP is not configured correctly on the interfaces.
C. The command mls rp management-interface is missing.
D. The command mls rp ip must be disabled to enable the routing.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 163
Which three statements are true of the Link Aggregation Control Protocol (LACP)? (Choose three.)
A. LACP is used to connect to non-Cisco devices.
B. LACP packets are sent with the command channel-group 1 mode desirable.
C. LACP packets are sent with the command channel-group 1 mode active.
D. Standby interfaces should be configured with a higher priority.
E. Standby interfaces should be configured with a lower priority.
Correct Answer: ACD Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 164
Refer to the exhibit. A workstation PC is connected to the Cisco IP phone access port. Based on the
configuration in the exhibit, how will the traffic be managed?
A. The IP phone access port will override the priority of the frames received from the PC.
B. The IP phone access port will trust the priority of the frames received from the PC.
C. The switch port Fa0/4 will override the priority of the frames received from the PC.
D. The switch port Fa0/4 will trust the priority for the frames received from the PC.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 165
Refer to the exhibit. A trunk link is connected between switch A_SW and switch D_SW. Based on the
configuration shown in the exhibit, how would the traffic coming from the switch A_SW be managed?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. The trunk port Fa0/1 on switch A_SW will trust all CoS values on the frames coming from the IP phone.
B. The trunk port Fa0/1 on switch A_SW will trust all CoS values on the frames received on the IP phone.
C. The trunk port Fa0/1 on switch D_SW will trust all CoS values on the frames coming from port Fa0/1 on A_SW.
D. The trunk port Fa0/1 on switch D_SW will trust all CoS values on the frames received on the A_SW switch port Fa0/4.
E. The trunk port Fa0/1 on switch D_SW will trust all CoS values on the frames received on the IP phone port.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 166
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest
method to the slowest method?
A. CEF, distributed CEF (dCEF), fast switching, process switching
B. distributed CEF (dCEF), CEF, fast switching, process switching
C. fast switching, process switching, distributed CEF (dCEF), CEF
D. process switching, fast switching, distributed CEF (dCEF), CEF
E. process switching, distributed CEF (dCEF), CEF, fast switching
F. process switching, CEF, distributed CEF (dCEF), fast switching TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
Correct Answer: B Section: (none) Explanation Explanation/Reference:
QUESTION 167
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not
receive a BPDU from its neighbor for three consecutive hello time intervals?
A. RSTP information is automatically aged out.
B. The port sends a TCN to the root bridge.
C. The port moves to listening state.
D. The port becomes a normal spanning tree port.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 168
Refer to the exhibit. Why does the trust state of interface FastEthernet 0/3 show “not trusted”?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. DSCP map needs to be configured for VOIP.
B. ToS has not been configured.
C. ToS has been misconfigured.
D. The command mls qos needs to be turned on in global configuration mode.
E. There is not a Cisco Phone attached to the interface.
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 169
What two things will occur when an edge port receives a BPDU? (Choose two.)
A. The port immediately transitions to the Forwarding state.
B. The switch generates a Topology Change Notification (TCN) BPDU.
C. The port immediately transitions to the err-disable state.
D. The port becomes a normal STP switch port.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 170
What two pieces of information will the show vlan id 5 command display? (Choose two.)
A. VLAN information on port 0/5
B. ports in VLAN 5
C. MTU and type
D. utilization
E. filters
Correct Answer: BC Section: (none) Explanation
Explanation/Reference:
QUESTION 171
Based on the network diagram and routing table output in the exhibit, which of these statements is
true?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. InterVLAN routing has been configured properly, and the workstations have connectivity to each other.
B. InterVLAN routing will not occur since no routing protocol has been configured.
C. Although interVLAN routing is not enabled, both workstations will have connectivity to each other.
D. Although interVLAN routing is enabled, the workstations will not have connectivity to each other.
Correct Answer: A Section: (none) Explanation
Explanation/Reference: QUESTION 172
What is the default VTP advertisement for subset advertisements in Catalyst switches that are in server or client mode?
A. 5 seconds
B. 10 seconds
C. 30 seconds
D. 1 minute
E. 5 minutes
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 173
Refer to the exhibit. Based upon the debug output that is shown, which three statements about HSRP
are true? (Choose three.)
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. The final active router is the router with IP address 172.16.11.111.
B. The router with IP address 172.16.11.111 has preempt configured.
C. The priority of the router with IP address 172.16.11.112 is preferred over the router with IP address
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 174
16.11.111.
A. The IP address 172.16.11.115 is the virtual HSRP IP address.
B. The router with IP address 172.16.11.112 has nonpreempt configured.
C. The router with IP address 172.16.11.112 is using default HSRP priority.
Correct Answer: AB Section: (none) Explanation
Explanation/Reference:
QUESTION 175
What must be configured on a Cisco switch in order to advertise VLAN information?
A. VTP password
B. VTP domain name
C. VTP revision number
D. VTP mode
E. VTP pruning
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 176
Which describes the default load balancing scheme used by the Gateway Load Balancing Protocol
(GLBP)?
A. per host basis using a round-robin scheme
B. per host basis using a strict priority scheme
C. per session using a round-robin scheme
D. per session using a strict priority scheme
E. per GLBP group using a round-robin scheme TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
F. per GLBP group using a strict priority scheme
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 177
When authentication is required, where must 802.1x be configured in order to connect a PC to a
switch?
A. client PC only
B. switch port only
C. switch port and client PC
D. switch port and local router port
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 178
How are STP timers and state transitions affected when a topology change occurs in an STP
environment?
A. All ports will temporarily transition to the learning state for a period equal to the max age timer plus the forward delay interval.
B. All ports will transition temporarily to the learning state for a period equal to the forward delay interval.
C. The default aging time for MAC address entries will be reduced for a period of the max age timer plus the forward delay interval.
D. The default hello time for configuration BDPUs will be reduced for the period of the max age timer.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 179
Refer to the exhibit. VTP has been enabled on the trunk links between all switches within the TEST
domain. An administrator has recently enabled VTP pruning. Port 1 on Switch 1 and port 2 on Switch 4 are
assigned to VLAN 2. A broadcast is sent from the host connected to Switch 1. Where will the broadcast
propagate?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. Every switch in the network receives the broadcast and will forward it out all ports.
B. Every switch in the network receives the broadcast, but only Switch 4 will forward it out port 2.
C. Switches 1, 2, and 4 will receive the broadcast, but only Switch 4 will forward it out port 2.
D. Only Switch 4 will receive the broadcast and will forward it out port 2.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 180
Refer to the exhibit. VLAN 1 and VLAN 2 are configured on the trunked links between Switch A and Switch B. Port Fa 0/2 on Switch B is currently in a blocking state for both VLANs. What should be done to load balance VLAN traffic between Switch A and Switch B?
A. Lower the port priority for VLAN 1 on port 0/1 for Switch A.
B. Lower the port priority for VLAN 1 on port 0/2 for Switch A.
C. Make the bridge ID of Switch B lower than the ID of Switch A.
D. Enable HSRP on the access ports.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 181
Refer to the exhibit. Which two problems are the most likely cause of the exhibited output? (Choose
two.)
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. spanning tree issues
B. HSRP misconfiguration
C. VRRP misconfiguration
D. physical layer issues
E. transport layer issues
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 182
Refer to the exhibit. Initially, LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link? (Choose two.)
A. The switch port attached to LinkB will not transistion to up.
B. One of the two switch ports attached to the hub will go into blocking mode when a BPDU is received.
C. Both switch ports attached to the hub will transition to the blocking state.
D. A heavy traffic load could cause BPDU transmissions to be blocked and leave a switching loop.
E. The switch port attached to LinkA will immediately transition to the blocking state.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 183
Refer to the exhibit and the partial configuration on routers R1 and R2. Hot Standby Routing Protocol (HSRP) is configured on the network to provide network redundancy for the IP traffic. The network administrator noticed that R2 does not became active when the R1 serial0 interface goes down. What should be changed in the configuration to fix the problem?
A. R2 should be configured with a HSRP virtual address.
B. R2 should be configured with a standby priority of 100.
C. The Serial0 interface on router R1 should be configured with a decrement value of 20.
D. The Serial1 interface on router R2 should be configured with a decrement value of 20.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 184
Refer to the exhibit. Which statement is true about the output?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. The port on switch CAT1 is forwarding and sending BPDUs correctly.
B. The port on switch CAT1 is blocking and sending BPDUs correctly.
C. The port on switch CAT2 is forwarding and receiving BPDUs correctly.
D. The port on switch CAT2 is blocking and sending BPDUs correctly.
E. The port on switch CAT3 is forwarding and receiving BPDUs correctly.
F. The port on switch CAT3 is forwarding, sending, and receiving BPDUs correctly.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 185
Refer to the exhibit. What statement is true based upon the configuration of router R1 and router R2?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. Router R1 will become the active virtual gateway.
B. Router R2 will become the active virtual gateway.
C. The hello and hold timers are incompatible with multi-homed BGP.
D. The hello and hold timers are incompatible with OSPF type 5 LSAs.
E. Router R1 will become the master for Virtual Router 1, and router R2 will become the backup for Virtual Router 2.
F. Router R2 will become the master for Virtual Router 1, and router R1 will become the backup for Virtual Router 2.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 186
Refer to the exhibit. The switchport output in Figure 1 displays the default settings of interface
FastEthernet 0/13 on switch SW1. Figure 2 displays the desired interface settings. Which command
sequence would configure interface FastEthernet 0/13 as displayed in Figure 2?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode trunk SW1 (config-if)# switchport trunk native DATA SW1(config-if)# switchport trunk allowed vlan 1,10,20
B. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode dynamic auto SW1(config-if)# switchport trunk native DATA SW1(config-if)# witchport trunk allowed vlan add 1,10,20
C. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode dynamic desirable SW1(config-if)# switchport trunk native vlan DATA SW1(config-if)# switchport trunk allowed vlan 1,10,20
D. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode dynamic desirable SW1(config-if)# switchport trunk native vlan 10 SW1(config-if)# switchport trunk allowed vlan 1,10,20
E. SW1(config-if)# switchport trunk encapsulation dot1q SW1(config-if)# switchport mode dynamic desirable SW1(config-if)# switchport trunk native vlan 10
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 187
Refer to the exhibit. For what purpose is the command show ip cef used?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. to display rewritten IP unicast packets
B. to display ARP resolution packets
C. to display ARP throttling
D. to display TCAM matches
E. to display CEF-based MLS lookups
F. to display entries in the Forwarding Information Base (FIB)
Correct Answer: F Section: (none) Explanation
Explanation/Reference:
QUESTION 188
Which two statements are true about HSRP, VRRP, and GLBP? (Choose two.)
A. GLBP allows for router load balancing of traffic from a network segment without the different host IP configurations required to achieve the same results with HSRP.
B. GLBP allows for router load balancing of traffic from a network segment by utilizing the creation of multiple standby groups.
C. GLBP and VRRP allow for MD5 authentication, whereas HSRP does not.
D. Unlike HSRP and VRRP, GLBP allows automatic selection and simultaneous use of multiple available gateways.
E. HSRP allows for multiple upstream active links being simultaneously used, whereas GLBP does not.
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 189
Refer to the exhibit. Host A and Host B are connected to the Catalyst 3550 switch and have been
assigned to their respective VLANs. The rest of the 3550 configuration is the default configuration. Host A is able to ping its default gateway, 10.10.10.1, but is unable to ping Host B. Given the output displayed in the exhibit, which statement is true?
A. HSRP must be configured on SW1.
B. A separate router is required to support interVLAN routing.
C. Interface VLAN 10 must be configured on the SW1 switch.
D. The global config command ip routing must be configured on the SW1 switch.
E. VLANs 10 and 15 must be created in the VLAN database mode.
F. VTP must be configured to support interVLAN routing.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 190
Refer to the exhibit and the show interfaces fastethernet0/1 switchport outputs. Users in VLAN 5 on
switch SW_A complain that they do not have connectivity to the users in VLAN 5 on switch SW_B. What
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside should be done to fix the problem?
A. Configure the same number of VLANs on both switches.
B. Create switch virtual interfaces (SVI) on both switches to route the traffic.
C. Define VLAN 5 in the allowed list for the trunk port on SW_A.
D. Disable pruning for all VLANs in both switches.
E. Define VLAN 5 in the allowed list for the trunk port on SW_B
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 191
What does the Catalyst switch interface configuration command switchport trunk native vlan 7
accomplish?
A. configures the interface to be a trunking port and causes traffic on VLAN 7 to be 802.1q tagged
B. causes the interface to apply ISL framing for traffic on VLAN 7
C. configures the trunking interface to send traffic from VLAN 7 untagged
D. configures the trunking interface to forward traffic from VLAN 7
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 192
Refer to the exhibit. The show port-security interface fa0/1 command was issued on switch SW1.
Given the output that was generated, which two security statement are true? (Choose two.)
A. Interface FastEthernet 0/1 was configured with the switchport port-security aging command.
B. Interface FastEthernet 0/1 was configured with the switchport port-security protect command.
C. Interface FastEthernet 0/1 was configured with the switchport port-security violation restrict command.
D. When the number of secure IP addresses reaches 10, the interface will immediately shut down.
E. When the number of secure MAC addresses reaches 10, the interface will immediately shut down and an SNMP trap notification will be sent.
Correct Answer: BE Section: (none) Explanation
Explanation/Reference: QUESTION 193
Which two statements about the various implementations of STP are true? (Choose two.)
A. Common Spanning Tree maintains a separate spanning-tree instance for each VLAN configured in the network.
B. The Spanning Tree Protocol (STP) is an evolution of the IEEE 802.1w standard.
C. Per-VLAN Spanning Tree (PVST) supports 802.1Q trunking. TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
D. Per-VLAN Spanning Tree Plus(PVST+) is an enhancement to 802.1Q specification and is supported only on Cisco devices.
E. Rapid Spanning Tree Protocol (RSTP) includes features equivalent to Cisco PortFast, UplinkFast, and BackboneFast for faster network reconvergence.
F. Multiple Spanning Tree (MST) assumes one spanning-tree instance for the entire Layer 2 network, regardless of the multiple number of VLANs.
Correct Answer: DE Section: (none) Explanation
Explanation/Reference:
QUESTION 194
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all
switches in the network. SW_B receives this error message on the console port:
00:06:34:
%CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/5 (not half
duplex),
with SW_A FastEthernet0/4 (half duplex) ,
with TBA05071417(Cat6K-B) 0/4 (half duplex).
What would be the possible outcome of the problem?
A.
The root port on switch SW_A will automatically transition to full-duplex mode.
B.
The root port on switch SW_B will fallback to full-duplex mode.
C.
The interfaces between switches SW_A and SW_B will transition to a blocking state.
D.
Interface Fa 0/6 on switch SW_B will transition to a forwarding state and create a bridging loop. TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 195
Which two statements are true about BPDU port-guard and BPDU filtering? (Choose two.)
A. BPDU port-guard can be enabled globally, whereas BPDU filtering must be enabled on a per-interface basis.
B. When globally enabled, BPDU port-guard and BPDU filtering apply only to PortFast enabled ports.
C. When globally enabled, BPDU port-guard and BPDU filtering apply only to trunking-enabled ports.
D. When a BPDU is received on a BPDU port-guard enabled port, the interface goes into the err-disabled state.
E. When a BPDU is received on a BPDU filtering enabled port, the interface goes into the err-disabled state.
F. When a BPDU is received on a BPDU filtering enabled port, the interface goes into the STP blocking state.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 196
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the
STP configuration is correct, what will be true about Switch 15?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. All ports will be in forwarding mode.
B. All ports in VLAN 10 will be in forwarding mode.
C. All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in blocking mode.
D. All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in standby mode.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 197
Refer to the exhibit. Which statement is true?
A. IP traffic matching access list ABC is forwarded through VLANs 5-10.
B. IP traffic matching VLAN list 5-10 will be forwarded, and all other traffic will be dropped.
C. All VLAN traffic matching VLAN list 5-10 will be forwarded, and all traffic matching access list ABC is dropped.
D. All VLAN traffic in VLANs 5-10 that match access list ABC will be forwarded, and all else will be dropped.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 198
Refer to the exhibit. Switch P1S1 is not applying VLAN updates from switch P2S1. What are three
reasons why this is not occurring? (Choose three.)
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. Switch P2S1 is in server mode.
B. Switch P1S1 is in transparent mode.
C. The MD5 digests do not match.
D. The passwords do not match.
E. The VTP domains are different.
F. VTP trap generation is disabled on both switches.
Correct Answer: BDE Section: (none) Explanation
Explanation/Reference:
QUESTION 199
Refer to the exhibit. Based upon the output of show vlan on switch CAT2, what can we conclude about
interfaces Fa0/13 and Fa0/14?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. that interfaces Fa0/13 and Fa0/14 are in VLAN 1
B. that interfaces Fa0/13 and Fa0/14 are down
C. that interfaces Fa0/13 and Fa0/14 are trunk interfaces
D. that interfaces Fa0/13 and Fa0/14 have a domain mismatch with another switch
E. that interfaces Fa0/13 and Fa0/14 have a duplex mismatch with another switch
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 200
What must be the same to make multiple switches part of the same Multiple Spanning Tree (MST)?
A. VLAN instance mapping and revision number
B. VLAN instance mapping and member list
C. VLAN instance mapping, revision number, and member list
D. VLAN instance mapping, revision number, member list, and timers
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
Cisco 642-812 exam is a challenging Certification Exam. Besides the books, internet is considered to be a treasure house of knowledge. In Flydumps you can find your treasure house of knowledge. This is a site of great help to you. You will encounter the complex questions in the exam, but Passcert can help you to pass the exam easily. Flydumps Latest Cisco 642-812 dumps includes all the knowledge that must be mastered for the purpose of passing the Cisco 642-812 exam.
Welcome to download the newest Examwind 700-505 dumps: http://www.examwind.com/700-505.html
http://www.alnaba.org/sap-c-hanaimp-1-questions-helpful-sap-c-hanaimp-1-exam-guide-with-new-discount/
Welcome to download the newest Flydumps 300-207 VCE dumps: http://www.flydumps.com/300-207.html
A site with a decent screen would likely have a very good understanding environment. Rather than the consumer screen it’s essential to as well check for selections much like the query high quality as well as the way in which handy it really is intended for getting ready for the fundamental analyze! FLYDUMPS Cisco 642-812 exam sample questions is a reliable source of information for the candidates who want to take the Cisco 640-878 exam. The Cisco 642-812 is the composite exam associated with the Cisco 642-812 certification. The Cisco 642-812 certification strengthens the employment prospects and opens up myriads of opportunities for them. FLYDUMPS Cisco 642-812 exam sample questions provides the useful information about the exam.
QUESTION 127
Which statement is true about the Forward Information Base (FIB) table?
A. The FIB is derived from the IP routing table and is optimized for maximum lookup throughput.
B. The FIB table is derived from the Address Resolution Protocol table, and it contains Layer 2 rewrite (MAC) information for the next hop.
C. The FIB lookup is based on the Layer 2 destination MAC address.
D. When the FIB table is full, a wildcard entry redirects traffic to the Layer 3 engine.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 128
Refer to the exhibit. Both host stations are part of the same subnet but are in different VLANs. On the
basis of the information presented in the exhibit, which statement is true about an attempt to ping from host
to host?
A. A trunk port will need to be configured on the link between Sw_A and Sw_B for the ping command to be successful.
B. The two different hosts will need to be in the same VLAN in order for the ping command to be successful.
C. A Layer 3 device is needed for the ping command to be successful. TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
D. The ping command will be successful without any further configuration changes.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 129
Which switch command enables a trunking protocol that appends a four byte CRC to the packet?
A. Switch(config-if)#switchport trunk encapsulation dot1q
B. Switch(config-if)#switchport trunk encapsulation itef
C. Switch(config-if)#switchport trunk encapsulation fddi
D. Switch(config-if)#switchport trunk encapsulation isl
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 130
Which statement describes Dynamic Trunking Protocol (DTP) mode ‘desirable’?
A. The interface is put into permanent trunking mode and negotiates to convert the link into a trunk link.
B. The interface actively attempts to convert the link to a trunk link.
C. The interface is put into permanent trunking mode but prevented from generating DTP frames.
D. The interface is put into a passive mode, waiting to convert the link to a trunk link.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 131
Which three statements are correct with regard to the IEEE 802.1Q standard? (Choose three.)
A. the packet is encapsulated with a 26 byte header and a 4 byte FCS
B. the IEEE 802.1Q frame format adds a 4 byte field to a Ethernet frame
C. the IEEE 802.1Q frame retains the original MAC destination address
D. the IEEE 802.1Q frame uses multicast destination of 0x01-00-0c-00-00
E. protocol uses point-to-point connectivity
F. protocol uses point-to-multipoint connectivity
Correct Answer: BCE Section: (none) Explanation
Explanation/Reference:
QUESTION 132
In a customer’s network, VLAN Trunking Protocol (VTP) is running with a domain named main1.
VLANs 1,2,3,4,5,10,20 are active on the network. Suddenly the whole network goes down. No traffic is
being passed on VLANs 2,3,4,5,10,20, however traffic passes on VLAN 1 and indicates all switches are
operational. Right before the network problem occurred, a switch named TEST1 was added to the
network.
TestInside Help You Pass Any IT Exam
http://www.TestInside.com Testinside What three configuration issues on TEST1 could be causing the network outage? (Choose three.)
A. TEST1 is configured as a VTP server with a different domain name.
B. TEST1 is not configured to participate in VTP.
C. TEST1 is configured as a VTP server with the domain name main1.
D. TEST1 has a lower VTP configuration revision than the current VTP revision.
E. TEST1 has a higher VTP configuration revision than the current VTP revision.
F. TEST1 is configured with only VLAN1.
Correct Answer: CEF Section: (none) Explanation
Explanation/Reference:
QUESTION 133
Which DTP switchport mode parameter sets the switch port to actively send and respond to DTP negotiation frames?
A. access
B. trunk
C. no negotiate
D. dynamic desirable
E. dynamic auto
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 134
Which method of Layer 3 switching uses a forwarding information base (FIB)?
A. route caching
B. flow-based switching
C. demand-based switching
D. topology-based switching
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 135
Which protocol specified by RFC 2281 provides network redundancy for IP networks, ensuring that
user traffic immediately and transparently recovers from first-hop failures in network edge devices or
access circuits?
A. STP
B. IRDP TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
C. ICMP
D. HSRP
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 136
In which three HSRP states do routers send hello messages? (Choose three.)
A. standby
B. learn
C. listen
D. speak E. active
Correct Answer: ADE Section: (none) Explanation
Explanation/Reference:
QUESTION 137
Which protocol enables a group of routers to form a single virtual router and use the real IP address of
a router as the gateway address?
A. Proxy ARP
B. HSRP
C. IRDP
D. VRRP
E. GLBP
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 138
Which protocol inserts a four byte tag into the Ethernet frame and recalculates CRC value?
A. VTP
B. 802.1Q
C. DTP
D. ISL
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 139
What is the cause of jitter?
A. variable queue delays TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
B. packet drops
C. transmitting too many small packets
D. compression
Correct Answer: A Section: (none) Explanation
Explanation/Reference: QUESTION 140
The original frame is encapsulated and an additional header is added before the frame is carried over
a trunk link. At the receiving end, the header is removed and the frame is forwarded to the assigned VLAN.
This describes which technology?
A. DISL
B. DTP
C. IEEE 802.1Q
D. ISL
E. MPLS
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 141
On a multilayer Catalyst switch, which interface command is used to convert a Layer 3 interface to a
Layer 2 interface?
A. switchport
B. no switchport
C. switchport mode access
D. swithport access vlan vlan-id
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 142
Which two statements concerning STP state changes are true? (Choose two.)
A. Upon bootup, a port transitions from blocking to forwarding because it assumes itself as root.
B. Upon bootup, a port transitions from blocking to listening because it assumes itself as root.
C. Upon bootup, a port transitions from listening to forwarding because it assumes itself as root.
D. If a forwarding port receives no BPDUs by the max_age time limit, it will transition to listening.
E. If a forwarding port receives an inferior BPDU, it will transition to listening.
F. If a blocked port receives no BPDUs by the max_age time limit, it will transition to listening. TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
Correct Answer: BF Section: (none) Explanation
Explanation/Reference:
QUESTION 143
How does 802.1q trunking keep track of multiple VLAN’s?
A. modifies the port index of a data frame to indicate the VLAN
B. adds a new header containing the VLAN ID to the data frame
C. encapsulates the data frame with a new header and frame check sequence
D. tags the data frame with VLAN information and recalculates the CRC value
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 144
Given the above partial configuration, which two statements are true about VLAN traffic? (Choose two.)
A. VLANs 1-5 will be blocked if fa0/10 goes down.
B. VLANs 1-5 will use fa0/10 as a backup only.
C. VLANs 6-10 will use fa0/10 as a backup only.
D. VLANs 6-10 have a port priority of 128 on fa0/10.
E. VLANs 1-10 are configured to load share between fa0/10 and fa0/12.
Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 145
Given the above diagram and assuming that STP is enabled on all switch devices, which two
statements are true? (Choose two.)
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. DSW11 will be elected the root bridge.
B. DSW12 will be elected the root bridge.
C. ASW13 will be elected the root bridge.
D. P3/1 will be elected the nondesignated port.
E. P2/2 will be elected the nondesignated port.
F. P3/2 will be elected the nondesignated port.
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 146
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge. Which switch should the administrator configure as the root bridge and which configuration command must the administrator enter to accomplish this?
A. DSW11(config)# spanning-tree vlan 1 priority 4096
B. DSW12(config)# set spanning-tree priority 4096
C. ASW13(config)# spanning-tree vlan 1 priority 4096
D. DSW11(config)# set spanning-tree priority 4096 TestInside Help You Pass Any IT Exam http://www.TestInside.com
Testinside
E. DSW12(config)# spanning-tree vlan 1 priority 4096
F. ASW13(config)# set spanning-tree priority 4096
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 147
On a 3550 EMI switch, which three types of interfaces can be used to configure HSRP? (Choose three.)
A. loopback interface
B. SVI interface
C. routed port
D. access port
E. EtherChannel port channel
F. BVI interface
Correct Answer: BCE Section: (none) Explanation
Explanation/Reference:
QUESTION 148
Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on External_B fails?
A. standby 1 preempt
B. standby 1 track 10.10.10.1 TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
C. standby 1 priority 130
D. standby 1 track fastethernet 0/0
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 149
Examine the router output above. Which two items are correct? (Choose two.)
A. Router A will assume the active state if its priority is the highest.
B. If Ethernet 0/2 goes down, the standby router will take over.
C. When Ethernet 0/3 of RouterA comes back up, the priority will become 105.
D. The local IP address of Router A is 10.1.0.6.
E. The local IP address of Router A is 10.1.0.20.
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 150
Which router redundancy protocol cannot be configured for interface tracking?
A. HSRP
B. GLBP
C. VRRP
D. SLB
E. RPR
F. RPR+
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 151
Based on the show spanning-tree vlan 200 output shown in the exhibit, which two statements about
the STP process for VLAN 200 are true? (Choose two.)
A. BPDUs will be sent out every two seconds.
B. The time spent in the listening state will be 30 seconds.
C. The time spent in the learning state will be 15 seconds.
D. The maximum length of time that the BPDU information will be saved is 30 seconds.
E. This switch is the root bridge for VLAN 200.
F. BPDUs will be sent out every 10 seconds.
Correct Answer: BF Section: (none) Explanation
Explanation/Reference:
QUESTION 152
Which two statements are true when the extended system ID feature is enabled? (Choose two.)
A. The BID is made up of the bridge priority value(two bytes) and bridge MAC address (six bytes).
B. The BID is made up of the bridge priority (four bits), the system ID (12 bits), and a bridge MAC address (48 bits).
C. The BID is made up of the system ID (six bytes) and bridge priority value (two bytes).
D. The system ID value is the VLAN ID (VID).
E. The system ID value is a unique MAC address allocated from a pool of MAC addresses assigned to the switch or module.
F. The system ID value is a hex number used to measure the preference of a bridge in the spanning-tree algorithm.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 153
What can be determined about the HSRP relationship from the displayed debug output?
A. The preempt feature is not enabled on the 172.16.11.111 router.
B. The nonpreempt feature is enabled on the 172.16.11.112 router.
C. Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 154
16.11.112.
A. Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router
Correct Answer: Section: (none) Explanation
Explanation/Reference: QUESTION 155
16.11.111.
A. The IP address 172.16.11.111 is the virtual HSRP router IP address.
B. The IP address 172.16.11.112 is the virtual HSRP router IP address.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
Cisco 642-812 Questions and Answers Products basically comprise of the simulated Cisco 642-812 exam questions AND their most correct answers,accompanied with a methodical elucidation of the HP HP5-H07D exam answers and the probable wrong answers.The extent to which Cisco 642-812 exam Questions and Answers Products cover their Cisco subject is so thorough,that once you are done with a Cisco product,passing the Cisco 642-812 exam in first attempt should be a piece of cake.
Flydumps 300-207 dumps with PDF + Premium VCE + VCE Simulator: http://www.flydumps.com/300-207.html
Cisco 642-812 Real Demo, Helpful Cisco 642-812 Exam Test Questions UP To 50% Off
Flydumps Cisco 642-812 exam material details are researched and created by the Most Professional Certified Authors who are regularly using current exams experience to create precise and logical dumps.You can get questions and answers from many other websites or books, but logic is the main key of success, and Flydumps will give you this key of success.
QUESTION 111
Which three statements about STP timers are true? (Choose three.)
A. STP timers values (hello, forward delay, max age) are included in each BPDU.
B. A switch is not concerned about its local configuration of the STP timers values. It will only consider the value of the STP timers contained in the BPDU it is receiving.
C. To successfully exchange BPDUs between two switches, their STP timers value (hello, forward delay, max age) must be the same.
D. If any STP timer value (hello, forward delay, max age) needs to be changed, it should at least be changed on the root bridge and backup root bridge.
E. On a switched network with a small network diameter, the STP hello timer can be tuned to a lower value TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside to decrease the load on the switch CPU.
F. The root bridge passes the timer information in BPDUs to all routers in the Layer 3 configuration.
Correct Answer: ABD Section: (none) Explanation
Explanation/Reference: QUESTION 112
The lack of which two prevents VTP information from propagating between switches? (Choose two.)
A. VLAN 1
B. a trunk port
C. VTP priority
D. a root VTP server
Correct Answer: AB Section: (none) Explanation
Explanation/Reference:
QUESTION 113
Refer to the exhibit. An administrator is verifying that a CEF FIB entry exists to destination network
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 114
168.150.0. Given the output generated by the show ip cef and show adjacency detail commands, which three statements are true? (Choose three.)
A. There is a valid CEF entry for the destination network 192.168.150.0.
B. The “valid cached adjacency” entry indicates that CEF will put all packets going to such an adjacency to the next best switching mode.
C. The counters (0 packets, 0 bytes) indicate a problem with the 192.168.199.3 next hop IP address.
D. There is an adjacency for the 192.168.199.3 next hop IP address.
E. The number 003071506800 is the MAC address of the 192.168.199.3 next hop IP address. TestInside Help You Pass Any IT Exam
http://www.TestInside.com
Testinside
F. The number 003071506800 is the MAC address of the source IP address.
Correct Answer: ADE Section: (none) Explanation
Explanation/Reference:
QUESTION 115
Which two statements are true about a switched virtual interface (SVI)? (Choose two.)
A. An SVI is created by entering the no switchport command in interface configuration mode.
B. An SVI is created for the default VLAN (VLAN1) to permit remote switch administration by default.
C. An SVI provides a default gateway for a VLAN.
D. Multiple SVIs can be associated with a VLAN.
E. SVI is another name for a routed port.
Correct Answer: BC Section: (none) Explanation
Explanation/Reference:
QUESTION 116
What is the effect of configuring the following command on a switch?
Switch(config) # spanning-tree portfast bpdufilter default
A. If BPDUs are received by a port configured for PortFast, then PortFast is disabled and the BPDUs are processed normally.
B. If BPDUs are received by a port configured for PortFast, they are ignored and none are sent.
C. If BPDUs are received by a port configured for Portfast, the port will transition to forwarding state.
D. The command will enable BPDU filtering on all ports regardless of whether they are configured for BPDU filtering at the interface level.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 117
Refer to the exhibit. The user who is connected to interface FastEthernet 0/1 is on VLAN 10 and
cannot access network resources. On the basis of the information in the exhibit, which command sequence
would correct the problem?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. SW1(config)# interface fastethernet 0/1 SW1(config-if)# no shut
B. SW1(config)# interface fastethernet 0/1 SW1(config-if)# switchport mode access
C. SW1(config)# interface fastethernet 0/1 SW1(config-if)# switchport mode access SW1(config-if)# switchport access vlan 10
D. SW1(config)# vlan 10 SW1(config-vlan)# no shut
E. SW1(config)# vlan 10 SW1(config-vlan)# state active
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 118
Refer to the exhibit. What does the command channel-group 1 mode desirable do?
A. enables LACP unconditionally
B. enables PAgP only if a PAgP device is detected
C. enables PAgP unconditionally
D. enables Etherchannel only
E. enables LACP only if a LACP device is detected
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 119
Refer to the exhibit. On the basis of the output generated by the show commands, which two statements are true? (Choose two.)
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. All interfaces on the switch have been configured as access ports.
B. Because it has not been assigned to any VLAN, interface gigabitethernet 0/1 does not appear in the show vlan output.
C. Because it is configured as a trunk interface, interface gigabitethernet 0/1 does not appear in the show vlan output.
D. There are no native VLANs configured on the trunk.
E. VLAN 1 will not be encapsulated with an 802.1q header.
F. VLAN 2 will not be encapsulated with an 802.1q header.
Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 120
Refer to the exhibit. VLAN2, VLAN3, and VLAN10 are configured on the switch D-SW1. Host computers are on VLAN 2 (10.1.2.0), servers are on VLAN 3 (10.1.3.0), and the management VLAN is on VLAN10 (10.1.10.0). Hosts are able to ping each other but are unable to reach the servers. On the basis of the exhibited output, which configuration solution could rectify the problem?
A. Enable IP routing on the switch D-SW1.
B. Configure a default route that points toward network 200.1.1.0/24.
C. Assign an IP address of 10.1.3.1/24 to VLAN3. TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
D. Configure default gateways to IP address 10.1.2.1 on each host.
E. Configure default gateways to IP address 10.1.10.1 on each host.
F. Configure default gateways to IP address 200.1.1.2 on each host.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 121
Refer to the show interface Gi0/1 switchport command output shown in the exhibit. Which two statements are true about this interface? (Choose two.)
A. This interface is a dot1q trunk passing all configured VLANs.
B. This interface is configured for access mode.
C. This interface is a member of VLAN1.
D. This interface is a member of VLAN7.
E. This interface is a member of a voice VLAN.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference: QUESTION 122
Refer to the exhibit. Which statement is true when voice traffic is forwarded on the same VLAN used by
the data traffic?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. Quality of service cannot be applied for the voice traffic.
B. The voice traffic cannot be forwarded to the distribution layer.
C. Port security cannot be enabled on the switch that is attached to the IP phone.
D. The voice traffic cannot use 802.1p priority tagging.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 123
Which two statements are true about recommended practices in VLAN design? (Choose two.)
A. Routing should occur at the access layer if voice VLANs are utilized. Otherwise, routing should occur at the distribution layer.
B. Routing should always be performed at the distribution layer.
C. Routing should not be performed between VLANs located on separate switches.
D. VLANs should be localized to a switch.
E. VLANs should be localized to a single switch unless voice VLANs are being utilized.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 124
Refer to the exhibit. What statement is true about the configuration on switch CAT1?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. The configuration overrides 802.1p priorities on packets entering ports Fa0/11 and Fa0/12 with a value of
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 125
A. The configuration establishes policed DSCP on ports Fa0/11 and Fa0/12 with values ranging from 8 to
Correct Answer: Section: (none) Explanation Explanation/Reference:
QUESTION 126
A. The configuration overrides the Quality of Service value in packets entering ports Fa0/11 and Fa0/12 with a value of 45.
B. Two IP phones with the MAC addresses of 0008.8595.d1a7 and 0007.8595.d2b7 are connected to CAT1 ports Fa0/11 and Fa0/12, respectively.
C. Security violation shutdown mode has been activated for ports Fa0/11 and Fa0/12. TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
D. Untagged Port VLAN ID (PVID) frames will carry voice traffic on VLAN 40.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
You will pass your Cisco 642-812 exam GUARANTEED using our accurate Cisco 642-812 practice questions and answers PDF&VCE dumps. Flydumps exam dumps will help you not only pass in the first try, but also save your valuable time. Give your career a boost and start earning your Cisco certification today!
The 100% valid latest Cisco 642-812 question answers ensure you 100% pass! And now we are offering the free Cisco 642-812 new version along with the VCE format Cisco 642-812 practice test. Free download more new Cisco 642-812 PDF and VCE on Flydumps.com.
QUESTION 73
With Cisco Express Forwarding, prefixes that require exception processing can be cached with one of
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
which four special adjacencies. (Choose four.)
A. forward
B. null
C. glean
D. kick
E. discard
F. drop
Correct Answer: BCEF Section: (none) Explanation
Explanation/Reference: QUESTION 74
Refer to the exhibit. Why are users from VLAN 100 unable to ping users on VLAN 200?
A. Encapsulation on the switch is wrong.
B. Trunking needs to be enabled on Fa0/1.
C. The native VLAN is wrong.
D. VLAN 1 needs the no shutdown command.
E. IP routing needs to be enabled on the switch.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 75
Refer to the exhibit. What problem is preventing users on VLAN 100 from pinging addresses on VLAN
200?
A. No default route on DLS1.
B. Encapsulation mismatch between switches.
C. Native VLAN mismatch.
D. Subinterfaces should be created on Fa0/7 and Fa0/8 on DLS1.
E. Trunking needs to be enabled.
F. The ip routing command is missing on DLS1.
Correct Answer: F Section: (none) Explanation
Explanation/Reference:
QUESTION 76
An attacking device has gained unauthorized access to data on a different VLAN through the use of
double tagging. What is the name of this network attack?
A. switch spoofing TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
B. IP spoofing
C. VLAN hopping
D. VLAN jumping
E. DHCP spoofing
F. MAC flooding
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 77
Which three characteristics are true about voice traffic in the campus network? (Choose three.)
A. bursty
B. greedy
C. drop sensitive
D. delay sensitive
E. UDP priority
F. TCP retransmits
Correct Answer: CDE Section: (none) Explanation
Explanation/Reference:
QUESTION 78
Which three characteristics are true about voice traffic in the campus network? (Choose three.)
A. TCP retransmits
B. benign
C. greedy
D. drop sensitive
E. smooth
F. delay insensitive
Correct Answer: BDE Section: (none) Explanation
Explanation/Reference:
QUESTION 79
Which two statements are true about voice VLANs? (Choose two.)
A. Voice VLANs allow IP phones to be moved around without worrying about subnets.
B. Voice VLANs allow voice and data packets to be logically combined.
C. Implementing voice VLANs causes network administrators to change their existing IP topology.
D. Using voice VLANs makes it easier for network administrators to identify and troubleshoot network TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside problems.
E. Voice VLANs are available on all Cisco switches.
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 80
Which two statements are true about trust boundaries? (Choose two.)
A. Classifying and marking traffic should be done as close to the traffic source as possible.
B. Classifying and marking traffic should be done at the distribution layer.
C. Traffic is classified and marked as it travels through the network.
D. If untrusted traffic enters a switch, it can be marked with a new QoS value appropriate for the policy in place.
E. The trust boundary moves depending on the type of traffic entering the network.
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 81
In the event that two devices need access to a common server, but they cannot communicate with each
other, which security feature should be configured to mitigate attacks between these devices?
A. port security
B. dynamic ARP inspection
C. DHCP snooping
D. private VLANs
E. BPDU guard
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 82
A hacker is interested in seeing traffic from all switch ports on the switch that he is connected to,
including the ports belonging to other VLANs. What type of attack is he likely to implement?
A. MAC address flooding
B. ARP attack
C. spoofing attack
D. DHCP attack
E. VLAN hopping
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 83
Which statement best summarizes how DHCP snooping works?
A. DHCP snooping validates the header information of all DHCP replies and only allows the reply through if it has a matching request in the DSRT.
B. DHCP snooping validates all DHCP responses from all switch ports and only allows packets through if the destination port sent a DHCP request in the last 5 seconds.
C. DHCP snooping validates all DHCP responses from all switch ports and only allows packets through if the destination port specifically sent a DHCP request.
D. DHCP snooping determines which switch ports are trusted and can source all DHCP messages.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 84
Which three statements are true about DAI? (Choose three.)
A. DAI determines the validity of an ARP packet based on the valid MAC address-to-IP address bindings stored in the DHCP Snooping database.
B. DAI forwards all ARP packets received on a trusted interface without any checks.
C. DAI determines the validity of an ARP packet based on the valid MAC address-to-IP address bindings stored in the CAM table.
D. DAI forwards all ARP packets received on a trusted interface after verifying and inspecting the packet against the DAI table.
E. DAI intercepts all ARP packets on untrusted ports.
F. DAI is used to prevent against a DHCP Snooping attack.
Correct Answer: ABE Section: (none) Explanation
Explanation/Reference:
QUESTION 85
What does the auto qos voip cisco-phone command do?
A. If a Cisco IP phone is attached, the switch trusts the CoS.
B. The switch assigns a CoS value of 5 to incoming packets.
C. It turns on STP to see if a Cisco IP phone is attached.
D. If a Cisco IP phone is attached and removed, the switch continues to trust the CoS values as long as the switch is not rebooted.
E. It disables the trust boundary feature because the switch knows a Cisco IP phone is attached. TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
Correct Answer: A Section: (none) Explanation
Explanation/Reference: QUESTION 86
A network administrator would like to configure 802.1x port-based authentication, however, the client workstation is not 802.1x compliant. What is the only supported authentication server that can be used?
A. TACACS with LEAP extensions
B. TACACS+
C. RADIUS with EAP extensions
D. LDAP
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 87
A switch has been configured with PVLANs. With what type of PVLAN port should the default gateway be configured?
A. Isolated
B. Promiscuous
C. Community
D. Primary
E. Trunk
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 88
Workstations on a segment with HSRP running should have their IP default gateway configured for which device?
A. standby router
B. virtual router
C. router physically connected to the network segment
D. router closest to the network segment
E. backup router
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 89
Refer to the exhibit. The lightweight wireless architecture splits the processing of the 802.11 data and management protocols and the access point functionality between the access point and the WLAN
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
controller using split MAC approach. Which three functionalities are handled by the WLAN controller?
(Choose three.)
A. the transmission of beacon frames
B. the portions of the protocol that have real-time requirements
C. the response to Probe Request frames from clients
D. 802.11 authentication
E. 802.11 association and re-association (mobility)
F. 802.11 frame translation and bridging
Correct Answer: DEF Section: (none) Explanation
Explanation/Reference:
QUESTION 90
What is the function of the Service Set Identifier (SSID) in the wireless LAN?
A. The SSID should be configured on the client site only and provides data-privacy functions and authentication to the access point.
B. The SSID must match on both the client and the access point. The SSID is advertised in plain-text in the access point beacon messages.
C. The SSID must match on both the client and the access point and provides encryption keys for authentication to the access point.
D. The SSID must match on both the client and the access point and provides MAC Address Authentication to authenticate the client to the access point.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 91
Refer to the exhibit. Three different wireless groups of users are allowed to gain access to the wireless
LAN. What type of security policy should be enforced for the users in the Guest group?
TestInside Help You Pass Any IT Exam http://www.TestInside.com
Testinside
A. static WEP and MAC authentication
B. LEAP authentication
C. primary SSID with open or no WEP authentication
D. open authentication with WEP plus MAC authentication
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 92
Refer to the exhibit. Which statement is true about the repeater access point that is deployed in this wireless network?
A. The repeater access point should use a different SSID than the SSID configured on the parent access point.
B. The repeater access point should use a different WEP encryption method than the WEP encryption that is enabled on the parent access point.
C. The repeater access point reduces the throughput in half because it receives and then re-transmits each packet on the same channel.
D. The repeater access point requires a 10 percent channel overlap with channel of the root access point.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 93
What are two differences between the Autonomous WLAN solution and the Lightweight WLAN solution?
(Choose two.)
A. TACACS+ can only be used for authentication with the Cisco Lightweight WLAN solution.
B. CiscoWorks Wireless LAN Solution Engine can be used for management with the Autonomous WLAN Solution.
C. CiscoWorks Wireless LAN Solution Engine can be used for management with the Lightweight WLAN Solution.
D. Cisco Wireless LAN Controller is used to configure the access points in the Lightweight WLAN solution.
E. Cisco Wireless LAN Controller is used to configure the access points in the Autonomous WLAN solution.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 94
Which statement is true about the data traffic between the access point and controller?
A. The data traffic is switched at the access point before being sent to the WLAN controller where VLAN tagging and QoS are applied.
B. The data traffic is encrypted with AES.
C. The data traffic between the access point and controller is encrypted.
D. The data traffic is encapsulated with LWAPP.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 95
How are VRRP messages exchanged between routers sharing a common LAN segment?
A. VRRP relies on TCP to open a connection and to maintain that connection using TCP keepalives.
B. Unicast IP addresses with UDP port ID 112.
C. Destination IP address 224.0.0.18 with IP Protocol ID 112.
D. VRRP messages are directly encapsulated into the Ethernet data field using type code 0x112.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 96
Refer to the exhibit. Based on the minimal VRRP configuration, which VRRP command issued on RTA
will ensure that RTA is the master virtual router?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. vrrp 100 priority 0
B. vrrp 100 priority 1
C. vrrp 100 priority 100
D. vrrp 100 priority 254
E. vrrp 100 preempt
F. no vrrp 100 preempt
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 97
Refer to the exhibit. What does the output of the debug command indicate on VRRP router RTA?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. VRRP is not active on RTA.
B. RTB does not have VRRP active.
C. RTA does not have VRRP preempt active.
D. RTB has a different IP address coded for VRRP group 1 than RTA.
E. RTB has the same IP address coded on its Ethernet interface as RTA.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 98
Which method enables GLBP to forward traffic from a LAN segment via multiple routers
simultaneously?
A. Clients need to have different default gateway IP addresses coded.
B. Separate GLBP groups are coded on the routers.
C. The AVG assigns different virtual MAC addresses.
D. Multiple AVG designated routers respond to ARP requests.
E. Proxy ARP allows multiple routers to respond to ARP requests from clients.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 99
How are GLBP messages exchanged between routers that share a common LAN segment?
A. GLBP messages are multicast to UDP port ID 3222.
B. GLBP messages are directly encapsulated into the Ethernet data field using type code 3222.
C. GLBP relies on TCP to open a connection and to maintain that connection using TCP keepalives.
D. Routers inform clients with GLBP messages and use ARP messages to exchange information about first-hop redundancy.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 100
Which method used by GLBP allows the AVG to prefer one GLBP router as the AVF over other GLBP routers until its tracked interface goes down, when another router might be more preferred?
A. no glbp group load-balancing
B. glbp group load-balancing host-dependent
C. glbp group load-balancing round-robin
D. glbp group load-balancing weighted
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 101
Refer to the exhibit. If VLAN 21 does not exist before typing the commands, what is the result of the configuration applied on switch SW1?
A. A new VLAN 21 is created and port 0/8 is assigned to that VLAN.
B. A new VLAN 21 is created, but no ports are assigned to that VLAN.
C. No VLAN 21 is created and no ports are assigned to that VLAN.
D. Configuration command vlan database should be used first to create the VLAN 21.
Correct Answer: A Section: (none) Explanation
Explanation/Reference: QUESTION 102
Refer to the exhibit. The link between switch SW1 and switch SW2 is configured as a trunk, but the trunk failed to establish connectivity between the switches. Based on the configurations and the error TestInside Help You Pass Any IT Exam
http://www.TestInside.com Testinside messages received on the console of SW1, what is the cause of the problem?
A. The two ends of the trunk have different duplex settings.
B. The two ends of the trunk have different EtherChannel configuration.
C. The two ends of the trunk have different native VLAN configuration.
D. The two ends of the trunk allow different VLANs on the trunk.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 103
What action should a network administrator take to enable VTP pruning on an entire management
domain?
A. enable VTP pruning on any client switch in the domain
B. enable VTP pruning on every switch in the domain
C. enable VTP pruning on any switch in the management domain
D. enable VTP pruning on a VTP server in the management domain
Correct Answer: D Section: (none) Explanation Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 104
Which process plays a major role in the creation of the CEF adjacency table?
A. Address Resolution Protocol (ARP)
B. PDU header rewrite
C. NetFlow switching
D. hello packet exchange
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 105
How does VTP pruning enhance network bandwidth?
A. by restricting unicast traffic to across VTP domains
B. by reducing unnecessary flooding of traffic to inactive VLANs
C. by limiting the spreading of VLAN information
D. by disabling periodic VTP updates
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 106
The network operations center has received a call stating that users in VLAN 107 are unable to access
resources through Router 1. From the information contained in the graphic, what is the cause of this
problem?
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. VLAN 107 does not exist on switch A.
B. VTP is pruning VLAN 107
C. VLAN 107 is not configured on the trunk
D. spanning tree is not enabled on VLAN 107
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 107
Which two table types are CEF components?(Choose two.)
A. forwarding information base
B. adjacency tables
C. neighbor tables TestInside Help You Pass Any IT Exam http://www.TestInside.com
Testinside
D. caching tables
E. route tables
Correct Answer: AB Section: (none) Explanation
Explanation/Reference:
QUESTION 108
Which Cisco IOS command assigns a Catalyst switch port to VLAN 10?
A. switchport mode vlan 10
B. switchport trunk native 10
C. switchport access vlan 10
D. switchport mode access vlan 10
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 109
Which statement is true regarding the configuration of ISL trunks?
A. All Catalyst switches support ISL trunking.
B. A Catalyst switch will report giants if one side is configured for ISL while the other side is not.
C. ISL trunking requires that native VLANs match.
D. A Catalyst switch cannot have ISL and IEEE 802.1q trunks enabled.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 110
Which three statements are true regarding the above diagram? (Choose three.)
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. A trunk link will be formed.
B. Only VLANs 1-1001 will travel across the trunk link.
C. The native VLAN for Switch B is vlan 1.
D. DTP is not running on Switch A.
E. DTP packets are sent from Switch B.
Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:
Cisco 642-812 Questions and Answers Products basically comprise of the simulated Cisco 642-812 exam questions AND their most correct answers,accompanied with a methodical elucidation of the Cisco 642-812 answers and the probable wrong answers.The extent to which Cisco 642-812 Questions and Answers Products cover their Cisco subject is so thorough,that once you are done with a Cisco product,passing the Cisco 642-812 exam in first attempt should be a piece of cake.