Cisco 640-802 Exam Certification Guide presents you with an organized test preparation routine through the use of proven series elements and techniques. “Do I Know This Already?” quizzes open each chapter and allow you to decide how much time you need to spend on each section. Cisco 640-802 lists and Foundation Summary tables make referencing easy and give you a quick refresher whenever you need it. Challenging Cisco 640-802 review questions help you assess your knowledge and reinforce key concepts. Cisco 640-802 exercises help you think about exam objectives in real-world situations, thus increasing recall during exam time.
Exam A
QUESTION 1
The following commands are executed on interface fa0/1 of 2950 Switch. Switch port port-security Switch port port-security mac-address sticky Switch port port-security maximum1
2950Switch (config-if)# switch port port-security 2950Switch (config-if)# switch port port-security mac-address sticky 2950Switch (config-if)# switch port port-security maximum1
The Ethernent frame that is shown arrives on interface fa0/1.Which two functions will occur when this frame rec two.)
Exhibit:
A. The MAC address table will now have an additional entry of fa0/1 FFFF FFFF FFFF.
B. Only host A will be allowed to transmit frames on fa0/1
C. This frame will be discarded when it is received by 2950Switch.
D. All frame will arriving on 2950Switch with a destination of 0000.00aa aaaa will be forwarded out fa0/1.
E. Hosts B and C may forward frames out fa0/1 but frames arriving from other switches will not be forward.
F. Only frames from source 0000.00bb bbbb. the first learned MAC address of 2950Switch, will be forward.
Correct Answer: BD Section: (none)Explanation
Explanation/Reference:
QUESTION 2
Multiple Questions
Enter IOS commands on the Dubai router to verify network operation and answer for multiple-choice
questions.
This TASK DOES NOT REQUIRE DEVICE CONFIGURATION.
Click on the Console PC to gain access to the console of the router. No console of enable passwords are
required.
There are four multiple-choice questions with this task. Be sure to answer all four questions before
selecting the Next button.
No console of enable passwords are required.
What destination Layer2 address will be used in the frame header containing a 172.30.0.4?
A.694
B.24
C.248
D.882
Which connection uses the default encapsulation for serial interfaces on Cisco routers?
A. The serial connection to the South branch office.
B. The serial connection to the North Coast branch office.
C. The serial connection to the North branch office.
D. The serial connection to the Multinational Core.
To access the multinle-choice question click on the numbered if required, what password shouldbe configured on the router in the North branch office to allow a connection to be established withthe Dubai router?
A. Console B.En8ble C.Scr8 D.T1net
E. No password is required
To access the multiple-choice questions, click on the numbered boxes on the left of the top panel.There are four multiple-choice questions with this task. Be sure to A static map to the C-AMERlocation is required. Which command should be used to create this map?
A. frame-relay map ip 172.30.0.3694 broadcast
B. frame-relay map ip 172.30.0.324 broadcast
C. frame-relay map ip 172.30.0.3248 broadcast
D. frame-relay map ip 172.30.0.3882 broadcast
Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
What destination Layer2 address will be used in the frame header containing a 172.30.0.4?
A.694
B.24
C.248
D.882
Answer: A
Which connection uses the default encapsulation for serial interfaces on Cisco routers?
A. The serial connection to the South branch office.
B. The serial connection to the North Coast branch office.
C. The serial connection to the North branch office.
D. The serial connection to the Multinational Core.
Answer: C
Click on the Consore PC to gain access to the cosore of the router. No console or enable password are required.
To access the multinle-choice question click on the numbered if required, what password shouldbe configured on the router in the North branch office to allow a connection to be established withthe Dubai router?
A. Console B.En8ble C.Scr8 D.T1net
E. No password is required
Answer: D
QUESTION 3
A.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
Bomar (Config)#interface fa0/0 Bomar(Config-if)#ip nat inside Bomar(Config)#interface S0/0 Bomar(Config-if)#ip nat outside Bomar(Config-if)#exit Bomar(Config)#access-list 1 permit 192.168.16.33 0.0.0.15 Bomar(Config)#ip nat pool nat_test 198.18.237.225 198.18.237.230 prefix-length 29 Bomar(Config)#ip nat
inside source list 1 pool nat_test overload Bomar(Config)#end Bomar#ping 192.0.2.114
( The command ping must be successful) QUESTION 4
To configure the router (Gotha) click on the console host icon that is connected to a router by a serial console cable(shown in the diagram as a dashed black line). you can click on the buttons below to view the different windows. Each of the windows can be minimized by clicking on the [-].You can also reposition a window by dragging it by the title bar. The “Tab”key and most commands that use the “Control” or “Escape” keys are not supported and are not necessary to complete this simulation. The help command does not display all commands of the help system. Central Florida Widgets recently installed a new router in their Gotha office. Complete the net work installation by performing the initial router configurations and configuring RIPv2 routing using the router command line interface(CLI) on the Gotha router. Configure the router per the following requirements: Name of the roter is Gotha Enable-secret password is mi222ke The password to access user EXEC mode using the console is G8tors1 The password to allow telnet accessto the router is dun63lap IPv4 addresses must be configured as follows: Ethernet network209.165.201.0/27-router has fourth assignable host address in subnet. Serial network is 192.0.2.176/28-router has last assignable host address in the subnet. Interfaces should be enabled. Routing protocol is RIPv2.
A.
Correct Answer: A Section: (none)Explanation
Explanation/Reference:
Router>enable Router#config terminal Router(config)#hostname Gotha Gotha(config)#enable secret mi222ke Gotha (config) #line console 0 Gotha (config-line) #password G8tors1 Gotha (config-line) #exit Gotha (config) #line vty 04 Gotha(config-line)#password dun63lab Gotha(config-line)#login Gotha(config-line)#exit Gotha(config)#interface fa0/0 Gotha(config-if)#ip address 209.165.201.4 255.255.255.224 Gotha(config-if)# no shutdown Gotha(config)#interface s0/0/0 Gotha(config-if)#ip address 192.0.2.190 255.255.255.240 Gotha(config-if)#clock rate 56000 Gotha(config-if)#no shutdown Gotha(config-if)#exit Gotha(config)#router rip Gotha(config-router)#version 2 Gotha(config-router)#network 209.165.201.0 Gotha(config-router)#network 192.0.2.176 Gotha(config-router)#no auto-summary Gotha(config-router)#end Gotha#copy run start
QUESTION 5
After adding TIS2 router, no routing updates are being exchanged between TIS1 and the new location. All other inter connectivity and Internet access for the existing locations of the company are working properly. The task is to identify the fault(s) and correct the router configuration to provide full connectivity between the routers. Access to the router CLI can be gained by clicking on the appropriate host. All passwords on all routers are cisco. IP addresses are listed in the chart below.
Click on host-G, complete the configration of the router in the pop-up CLI
******************************************************************************************* TISA# show run interface FastEthernet0/0
ip address 192.168.60.97 255.255.255.24
!
interface FastEthernet0/1
ip address 192.168.60.113 255.255.255.240
! interface Serial0/0 Ip address 192.168.36.14 255.255.255.252 Clockrate 64000 !
router eigrp 212
Network 192.168.36.0
Network 192.168.60.0
No auto-summary !
TISA# show ip route
192.168.36.0/30 is subnetted, 1 subnets
C 192.168.36.12 is directly connected, Serial0/0
192.168.60.0/24 is variably subnetted, 5 subnets, 2 masks
C 192.168.60.96/28 is directly connected, FastEthernet0/0
C 192.168.60.112/28 is directly connected, FastEthernet0/1
D 192.168.60.128/28 [ 90/21026560 ] via 192.168.36.13, 00:00:57, Serial0/0
D 192.168.60.144/28 [ 90/21026560 ] via 192.168.36.13, 00:00:57, Serial0/0
D 192.168.60.24/30 [ 90/21026560 ] via 192.168.36.13, 00:00:57, Serial0/0
D* 198.0.18.0 [ 90/21024000 ] via 192.168.36.13, 00:00:57, Serial0/0 ******************************************************************************************* TIS2# show run ! ! interface FastEthernet0/0 ip address 192.168.77.34 255.255.255.252 ! interface FastEtherner0/1 ip address 192.168.60.65 255.255.255.240 ! interface FastEthernet1/0 ip address 192.168.60.81 255.255.255.240 ! ! router eigrp 22 network 192.168.60.0 network 192.168.77.0 no auto-summary
TIS2# show ip route 192.168.60.0/28 is subnetted, 2 subnets C 192.168.60.80 is directly connected, FastEthernet1/0 C 192.168.60.64 is directly connected, FastEthernet0/1 192.168.77.0/30 is subnetted, 1 subnets C 192.168.77.32 is directly connected, FastEthernet0/0 ******************************************************************************************* TISB# show run
interface FastEthernet0/0
ip address 192.168.60.129 255.255.255.240 ! interface FastEthernet0/1 ip address 192.168.60.145 255.255.255.240 ! interface Serial0/1
ip address 192.168.60.26 255.255.255.252
router eigrp 212
network 192.168.60.0
network 192.168.60.0
TISB# show ip route
192.168.60.0/24 is variably subnetted, 5 subnets, 2 masks
C 192.168.60.24/30 is directly connected, Serial0/1
C 192.168.60.128/28 is directly connected, FastEthernet0/0
C 192.168.60.144/28 is directly connected, FastEthernet0/1
D 192.168.60.96/28 [ 90/21026560 ] via 192.168.60.25, 00:00:57, Serial0/1
D 192.168.60.112/28 [ 90/21026560 ] via 192.168.60.25, 00:00:57, Serial0/1
192.168.36.0/30 is subnetted, 1 subnets
D 192.168.36.12 [ 90/21026560 ] via 192.168.60.25, 00:00:57, Serial0/1
D* 198.0.18.0 [ 90/21024000 ] via 192.168.60.25, 00:00:57, Serial0/1 ********************************************************************************************************* TIS1# show run ! interface FastEthernet0/0 ip address 192.168.77.33 255.255.255.252 ! interface Serial1/0 ip address 198.0.18.6 255.255.255.0 ! interface Serial0/0 ip address 192.168.36.13 255.255.255.252 clockrate 64000 ! interface Serial0/1 ip address 192.168.60.25 255.255.255.252 clockrate 64000 ! ! router eigrp 212 network 192.168.36.0 network 192.168.60.0 network 192.168.85.0 network 198.0.18.0 no auto-summary ! ip classless ip default-network 198.0.18.0 ip route 0.0.0.0 0.0.0.0 198.0.18.5 ip http server
TIS1# sh ip route
192.168.36.0/30 is subnetted, 1 subnets
C 192.168.36.12 is directly connected, Serial0/0
192.168.60.0/24 is variably subnetted, 5 subnets, 2 masks
C 192.168.60.24/30 is directly connected, Serial0/1
D 192.168.60.128/28 [ 90/21026560 ] via 192.168.60.26, 00:00:57, Serial0/1 D 192.168.60.144/28
[ 90/21026560 ] via 192.168.60.26, 00:00:57, Serial0/1
D 192.168.60.96/28 [ 90/21026560 ] via 192.168.36.14, 00:00:57, Serial0/0 192.168.77.0/30 is subnetted,
1 subnets
C 192.168.77.32 is directly connected, FastEthernet0/0
C 198.0.18.0/24 is directly connected, Serial1/0
*S 0.0.0.0 via 198.0.18.5
A.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
Please input commands here: TIS2>enable TIS2#config t TIS2(config)#no router eigrp 22 TIS2(config)#router eigrp 212 TIS2(config-router)#network 192.16.60.0 TIS2(config-router)#network 192.16.77.0 TIS1>enable TIS1#config t TIS1(config)#router eigrp 212 TIS1(config-router)#network 192.16.77.0
QUESTION 6
Refer to the exhibit. Complete this network diagram by dragging the correct device name of description name or description to the correct location. Not all the names or descriptions will be used.
Select and Place:
Correct Answer: Section: (none) Explanation
Explanation/Reference:
This volume is part of the Exam Certification Guide Series from Cisco 640-802. Cisco 640-802 in this series provide officially developed exam preparation materials that offer assessment, review, and practice to help Cisco 640-802 Certification candidates identify weaknesses, concentrate their study efforts, and enhance their confidence as Cisco 640-802 exam day nears.