Nowdays,Flydumps has published the newest Cisco 642-832 exam dumps with free vce test software and pdf dumps, and the latest Cisco 642-832 question answers ensure you 100% pass and money bcak guarantee.
Exam A
QUESTION 1
You enabled CDP on two Cisco Routers are connected to each other. The Line and Protocol status for the interfaces on both routers show as UP but the routers do not see each other a CDP neighbors. Which layer of the OSI model does the problem most likely exist?
A. Physical
B. Session
C. Application
D. Data-Link
E. Network
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 2
You have the following commands on your Cisco Router:
ip ftp username admin ip ftp password backup
You have been asked to switch from FTP to HTTP. Which two commands will you use to replace the existing commands?
A. ip http username admin
B. ip http client username admin
C. ip http password backup
D. ip http client password backup
E. ip http server username admin
F. ip http server password backup
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 3
Refer to the graphic shown above. What statement is correct regarding the errors but just information messages.
A. These two log messages will not have a severity level. They are not errors but are just informational messages.
B. The first log message is categorized as a warning message.
C. These messages regarding interface status are normal output and will always be displayed when you exit config mode.
D. The first log message is an error message with a severity level of 3.
E. The second message would be shown if the logging consol warning command had been issued.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 4
FCAPS is a network maintenance model defined by ISO. It stands for which of the following?
A. Fault Management
B. Action Management
C. Configuration Management
D. Protocol Management
E. Security Management
Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:
QUESTION 5
Match the items on the left to their purpose on the right
Select and Place:
Correct Answer:
Section: (none) Explanation
Explanation/Reference:
EEM -> CLI based Management and Monitoring SDM -> Provides a GUI for Administration FTP -> Used for Backup and Restore
QUESTION 6
FCAPS is a network maintenance model defined by ISO. FCAPS stands for:
Select and Place:
Correct Answer:
Section: (none) Explanation
Explanation/Reference:
F -> Fault Management C -> Configuration Management A -> Accounting Management
Exam B
QUESTION 1
Client is able to ping 10.1.1.2 but 10.1.1.1. Initial troubleshooting shows that R1 does not have any OSPF neighbors or any OSPF routes.
Configuration on R1:
router ospf 1 log-adjacency-changes network 10.1.1.0 0.0.0.3 area 12 default-information originate always ! interface Serial0/0/0/0.12 point-to-point ip address 10.1.1.1 255.255.255.252 ip nat inside ip ospf message-digest-key 1 md5 TSHOOT
Configuration on R2:
router ospf 1 log-adjacency-changes network 10.1.1.0 0.0.0.3 area 12 ! interface Serial0/0/0/0.12 point-to-point ip address 10.1.1.2 255.255.255.252 ip ospf authentication message-digest ip ospf message-digest-key 1 md5 TSHOOT
1.On which device is the fault condition located?
2.
What is the solution of the fault condition?
3.
Fault Condition is related to which technology?
Exhibit:
A. R1
B. R2
C. DSW1
D. Client1
E. ip ospf authentication message-digest command has to be added on S0/0/0/0.12
F. ip ospf authentication message-digest command has to be added under the OSPF routing process
G. A static route to 10.1.1.4 must be added on R1
H. ip nat outside must be added on S0/0/0/0.12
I. NAT J. OSPF
K. Statis Routing
L. Switch to Switch Connectivity
Correct Answer: AEJ Section: (none) Explanation
Explanation/Reference:
QUESTION 2
Client 1 is able to ping 209.65.200.226 but not the Web Server at 209.65.200.241. Initial troubleshooting
shows and R1 does not have any BGP routes. R1 also does not show any active BGP neighbor.
In the above ticket R1 and all others are able to ping 209.65.200.226 but not the Web Server only. This is
because R1 is directly connected to 209.65.200.226 and BGP is not required in order to ping directly
connected network and as soon as R1 knows about 209.65.200.224 network all other devices are also
able to ping 209.65.200.226, since they are coming to R1 for any unknown route, because of default route
propagate through R1′s OSPF (using ‘default-information originate always’ command). However Web
Server is not accessible until BGP configured properly between R1 and ISP(209.65.200.226) because only
then R1 will receive the information about Web Server’s network.
Following are the symptoms of above ticket:
1- No one is able to ping Web Server.
2- Client 1 and all others can ping upto 209.65.200.226.
3- ‘sh ip route BGP’, you will not see any BGP route.
4- ‘sh ip bgp neighbor’ on R1, you will not see any active BGP neighbor.
Configuration on R1:
router bgp 65001 no synchronization bgp log-neighbor-changes network 209.65.200.224 mask 255.255.255.252 neighbor 209.56.200.226 remote-as 65002 no auto-summary
1.
Fault Condition is related to which technology?
2.
What is the solution of the fault condition?
3.
On which device is the fault condition located?
Exhibit:
A. EIGRP
B. HSRP
C. BGP
D. OSPF
E. R1
F. DSW1
G. R4
H. R2
I. Enable BGP synchronization
J. Change neighbor 209.56.200.226 remote-as 65002 statement to neighbor 209.56.200.226 remote-as 65001
K. Change neighbor 209.56.200.226 remote-as 65002 statement to neighbor 209.65.200.226 remote-as 65002
L. Change neighbor 209.56.200.226 remote-as 65002 statement to neighbor 209.65.200.226 remote-as 65001
Correct Answer: CEK Section: (none) Explanation
Explanation/Reference:
In this scenario you need to check bgp neighbotship “show ip bgp sum”.
The neighbor`s address in the neighbor command is wrong under router BGP (use ipv4 Layer 3).
You need to delete the wrong neighbor statement and enter the correct neighbor address in the neighbor
command (change 209.56.200.226 to 209.65.200.226).
QUESTION 3
Client 1 is not able to reach the WebServer. Initial troubleshooting shows that DSW1 can ping the Fa0/1 interface of R4 but not the s0/0/0/0.34 interface.
Configuration on DSW1:
router eigrp 10 network 10.1.4.4 0.0.0.0 network 10.2.1.1 0.0.0.0 network 10.2.4.13 0.0.0.0 no auto-summary
Configuration on DSW2:
router eigrp 10 network 10.1.4.8 0.0.0.0 network 10.2.2.1 0.0.0.0 network 10.2.4.14 0.0.0.0 no auto-summary
Configuration on R4:
router eigrp 10 network 10.1.4.5 0.0.0.0 no auto-summary redistribute ospf 1 metric 100 10 255 1 1500 route-map EIGRP_to_OSPF ! router ospf 1 network 10.1.1.8 0.0.0.0 area 34 redistribute eigrp 10 subnets ! route-map EIGRP->OSPF match ip address 1 ! access-list 1 permit 10.0.0.0 0.255.255.255 access-list 1 permit 209.0.0.0 0.255.255.255
1.
On which device is the fault condition located?
2.
Fault Condition is related to which technology?
3.
What is the solution of the fault condition?
Exhibit:
A. DSW1
B. DSW2
C. Client 1
D. R4
E. EIGRP
F. Route Redistribution
G. OSPF
H. IP Addressing
I. Remove the redistribute command from OSPF process on R4
J. Change the route-map name in the redistribute command under OSPF process to EIGRP->OSPF on R4
K. Change EIGRP AS to 1 on R4
L. Advertise 10.1.1.8/30 network in EIGRP on R4
Correct Answer: DFJ Section: (none)
Explanation
Explanation/Reference:
QUESTION 4
DSW1 and R4 cannot ping R2`s loopback or R2`s s0/0/0/0.12 IPv6 address. Initial troubleshooting shows that R2 is not on OSPFv3 neighbor on R3.
Configuration of R2:
ipv6 router ospf 6 router-id 2.2.2.2 ! interface s0/0/0/0.23 ipv6 address 2026::1:1/122
Configuration of R3:
ipv6 router ospf 6 router-id 3.3.3.3 ! interface s0/0/0/0.23 ipv6 address 2026::1:2/122 ipv6 ospf 6 area 0
1.
What is the solution of the fault condition?
2.
Fault Condition is related to which technology?
3.
On which device is the fault condition located?
Exhibit:
A. Add ipv6 ospf area 0 under S0/0/0/0.23 on R2
B. Add ipv6 ospf area 6 under S0/0/0/0.23 on R2
C. Remove ipv6 ospf area 6 from S0/0/0/0.23 on R2
D. Enable IPv6 routing on S0/0/0/0.23 on R2
E. IPv6 Addressing
F. Route Redistribution
G. OSPFv3
H. RIPng
I. DSW1
J. DSW2
K. R2
L. R3
Correct Answer: AGK Section: (none) Explanation
Explanation/Reference:
Cisco 642-832 Exam Certification Guide presents you with an organized test preparation routine through the use of proven series elements and techniques.“Do I Know This Already?”quizzes open each chapter and allow you to decide how much time you need to spend on each section.Cisco 642-832 lists and Foundation Summary tables make referencing easy and give you a quick refresher whenever you need it.Challenging Cisco 642-832 review questions help you assess your knowledge and reinforce key concepts.Cisco 642-832 exercises help you think about exam objectives in real-world situations, thus increasing recall during exam time.