Flydumps Cisco 642-359 exam questions and answers in PDF are prepared by our expert,Moreover,they are based on the recommended syllabus covering all the Adobe exam objectives. You will find them to be very helpful and precise in the subject matter since all the Cisco 642-359 exam content is regularly updated and has been checked for accuracy by our team of Adobe expert professionals.
QUESTION 20
A customer with multiple vendor switches establishes an ISL between a non-Cisco switch and an E_Port
on a Cisco MDS 9000 switch.
Which three statements are true about the interop behavior between the two switches? (Choose three.)
A. Exchange-based load balancing is supported in all interop modes.
B. Interop mode affects all VSANs.
C. Only E_Ports can be used to connect to non-Cisco MDS switches.
D. The non-Cisco switch must have matching FC timers with the VSAN containing the E_Port on the Cisco MDS 9000 Series switch.
E. Adding another ISL between the switches will allow a PortChannel to be configured for HA.
F. Interop mode 1 allows full featured communication between all combinations of MDS and non- MDS switches
Correct Answer: ACD Section: (none) Explanation
Explanation/Reference:
QUESTION 21
Which license is required on switches that are going to implement LUN zoning?
A. Storage Services Enabler
B. Enterprise license
C. Fabric Manager Server license
D. SAN Extension over IP license
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 22
DRAG DROP
Drop
Match the definition on the left with its appropriate word or phrase about switch interoperability on the right.
“Pass Any Exam. Any Time.” – www.actualtests.com 11
Cisco 642-359: Practice Exam
Drag and drop question. Drag the items to the proper locations.
A. 1=2, 2=1, 3=4, 4=5, 5=3
B.
C.
D.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
Explanation:
“Pass Any Exam. Any Time.” – www.actualtests.com 12 Cisco 642-359: Practice Exam
QUESTION 23
Which two of these logging statements are true? (Choose two.)
A. Call Home message level 0 is most urgent and level 7 is least urgent, whereas the syslog level 9 is most urgent and level 0 is least urgent.
B. Syslog message level 0 is most urgent and level 7 is least urgent, whereas the Call Home message level 9 is most urgent and level 0 is least urgent,
C. Syslog message level 7 is most urgent and level 0 is least urgent, whereas the Call Home message level 9 is most urgent and level 0 is least urgent.
D. Accounting logs can be stored locally and sent to remote AAA servers.
E. Go to logs > syslog > setup in Device Manager to view the local accounting log.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 24
Which of these Cisco Fabric Manager debugging tools can compare the current configuration with a previously saved configuration file?
A. Switch Health Analysis
B. Fabric Configuration Analysis
C. EnD.to-End Connectivity Analysis
D. Zone Merge Analysis
Correct Answer: B Section: (none) Explanation Explanation/Reference:
QUESTION 25
Choose the correct list of tasks to configure Remote Spanning.
A. Create a VSAN interface. Enable a Fibre Channel tunnel. Initiate the Fibre Channel tunnel. Configure the ST_Port in the source switch. Configure the SD_Port in the destination switch. Configure a SPAN session in the source switch.
B. Create a VSAN interface. Enable a Fibre Channel tunnel. Initiate the Fibre Channel tunnel. Configure the ST_Port in the source switch. Configure the SD_Port in the destination switch. Configure an RSPAN session in the source switch.
C. Create an RSPAN interface. Enable a Fibre Channel tunnel. Initiate the Fibre Channel tunnel. Configure the SD_Port in the destination switch. Configure the ST_Port in the source switch. Configure an RSPAN session in the source switch.
D. Create a VSAN interface. Enable a Fibre Channel tunnel. Initiate the Fibre Channel tunnel. Configure the ST_Port in the destination switch. Configure the SD_Port in the source switch. “Pass Any Exam. Any Time.” – www.actualtests.com 13 Cisco 642-359: Practice Exam Configure an RSPAN session in the source switch.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 26
When creating an Inter-VSAN routing topology, which type of World Wide Name (WWN) must be used?
A. Port WWN
B. Switch WWN
C. Fabric Port WWN
D. VSAN WWN
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 27
Your company has a multiswitch fabric including Switch A and Switch B. An administrator of Switch A creates the following zone set and successfully activates it: zoneset name ZoneSetl vsan 1 zone name Zonel vsan 1 pwwn 21:01:00:e0:8b:3c:03:b6 pwwn 21:01:00:e0:8b:3c:55:bb Later in the day, a second administrator creates the following zone set on Switch B: zoneset name ZoneSet2 vsan 1 zone name Zonel vsan 1 pwwn 21:01:00:e0:8b:3c:03:b6 pwwn 21:01:00:e0:8b:3c:55:aa What happens when the administrator of Switch B attempts to activate ZoneSet2?
A. ZoneSet2 becomes the active zone set for both Switches A and
B.
C. The fabric segments and ZoneSet2 become the active zone set for Switch B only.
D. The fabric segments and ZoneSet2 become the active zone set for Switch A only.
E. The fabric segments and ZoneSetl remain the active zone set for Switch B, while ZoneSet2 becomes the active zone set for Switch A.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 28
“Pass Any Exam. Any Time.” – www.actualtests.com 14 Cisco 642-359: Practice Exam
You have been asked to configure a port on your Cisco MDS switch so that a host can join your fabric. Which of these switch port types should the port be set to?
A. N_Port
B. NL_Port
C. F_Port
D. E_Port
E. TE_Port
F. SD Port
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 29
DRAG DROP
Drop The IT director wants to standardize the process that the SAN team follows when troubleshooting the SAN. IT director wants to leverage the tools that are provided by Cisco Fabric Manager so that each member of the team executes the samesteps when faced with a problem in the SAN. Click and drag the Cisco Fabric Manager troubleshooting tool to the purpose it serves in the repair strategy.
Drag and drop question. Drag the items to the proper locations.
A. 1=2, 2=4, 3=3, 4=1
B.
C.
D.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
“Pass Any Exam. Any Time.” – www.actualtests.com 15 Cisco 642-359: Practice Exam
Explanation:
QUESTION 30
Which of the following tools would you use to view SCSI error count statistics?
A. Cisco Performance Manager
B. RMON
C. Cisco Traffic Analyzer
D. Cisco Fabric Analyzer
Correct Answer: C Section: (none)
Explanation
Explanation/Reference:
QUESTION 31
A customer would like to implement a low-cost traffic engineering solution that provides a primary data path, and a secondary data path that will only be used in the event of a failure in the primary path. Which of these solutions best meets the customer needs?
A. VSAN allowed list pruning
B. FCC
C. QoS “Pass Any Exam. Any Time.” – www.actualtests.com 16 Cisco 642-359: Practice Exam
D. FSPF link costs
E. VOQ
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 32
The output from the switch show interface command indicates that the link from a host comes up as an FL_Port. The switch port is configured as auto. Which three of these HBA configurations could cause this scenario? (Choose three.)
A. the HBA is configured as an N_Port
B. the HBA is configured as an NL_Port
C. the HBA supports only NL mode
D. the HBA is configured as a TE_Port
E. the HBA supports only FC.AL technology
F. the HBA is configured as an TL_Port
Correct Answer: BCE Section: (none) Explanation
Explanation/Reference:
QUESTION 33
Refer to the exhibit. Which of the following statements is true?
A. All users belonging to the sangroup role are allowed to perform all configuration commands except fspf commands because the deny config feature fspf is listed first.
B. All users are allowed to perform all configuration commands because the permit config command is listed last and that will globally override all other rules.
C. All users belonging to the sangroup role to perform all configuration commands except fspf commands because it does not matter what order the rules are entered.
D. The configuration is not valid because rules are entered at the switch (config-role-vsan)# level.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 34
Which three types of network statistics can be captured with the Cisco Traffic Analyzer? (Choose three.)
“Pass Any Exam. Any Time.” – www.actualtests.com 17 Cisco 642-359: Practice Exam
A. historical reporting
B. total bandwidth used
C. Tx/Rx bandwidth per VSAN
D. Tx/Rx bandwidth per N_Port
E. class-based traffic breakdown
Correct Answer: BCD Section: (none) Explanation
Explanation/Reference:
QUESTION 35
Which two security protocols are supported in the Cisco iSCSI implementation? (Choose two.)
A. IPSec
B. FC.SP
C. SLAP
D. CHAP
E. PAP
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 36
Which feature requires the Cisco MDS 9000 Series Enterprise license?
A. PortChannels
B. virtual output queues
C. port security
D. centralized AAA services
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 37
Which three of these steps are required to configure IVR? (Choose three.)
A. Enable IVR in the border switches.
B. Configure interop mode 1.
C. Configure NAT.
D. Configure the IVR topology.
E. Create and activate IVR zone sets.
F. Configure a transit VSAN. “Pass Any Exam. Any Time.” – www.actualtests.com 18 Cisco 642-359: Practice Exam
Correct Answer: ADE Section: (none) Explanation
Explanation/Reference:
QUESTION 38
What is the default policy when defining role-based access for a VSAN?
A. Deny
B. Permit
C. Permit only for the default VSAN.
D. There is no default role policy for a VSAN.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 39
Which two features help you verify connectivity between host and storage devices? (Choose two.)
A. fcanalyzer
B. Cisco Traffic Analyzer
C. EnD.to-End Connectivity Analysis
D. Zone Merge Analysis
E. fcping
Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 40
Which two of these features are characteristic of out-of-band management for the Cisco MDS 9000 Series switches? (Choose two.)
A. CUP management of the switch for FICON
B. 10/100/1000 Ethernet connection C. IPFC
C. FCIP
D. logical interface VSAN 1
E. configuration during the initial switch setup
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 41
“Pass Any Exam. Any Time.” – www.actualtests.com 19 Cisco 642-359: Practice Exam
A customer has reported performance degradation in the SAN. The system administrator would like to track reaD.write I/O and LUN use on several devices. The devices are directly connected to various switches and belong to different VSANs. The administrator wants to gather information for the last 72 hours. Which of the following Cisco MDS 9000 Series tools is needed to track SCSI I/O and LUN statistics?
A. Cisco Fabric Manager
B. Cisco Traffic Analyzer and PAA
C. Cisco Performance Manager
D. Cisco Fabric Analyzer
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 42
Reference the exhibit.
A customer has configured an FCIP connection between two sites. The customer issues an extended IP
ping command to determine path availability, MTU, and rounD.trip time.
According to the output in the exhibit, which parameter in the extended ping needs adjustment in order to
increase the chances of establishing enD.to-end connectivity?
A. timeout in seconds
B. repeat count
C. datagram size
D. nothing, enD.to-end connectivity cannot be established
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
“Pass Any Exam. Any Time.” – www.actualtests.com 20 Cisco 642-359: Practice Exam
QUESTION 43
The HBA on your storage server only supports the NL_Port mode. Which interface type on the Cisco MDS 9000 Series fabric switches can support this HBA?
A. F
B. TE
C. FL
D. N
E. E
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 44
While examining the output of a show run command on the Cisco MDS 9000 Series, you notice that the statement interface GigabitEthernet2/1.2 appears in the output. What does this mean?
A. It refers to the second FCIP tunnel that is configured on port GigabitEthernet2/1.
B. It refers to a VLAN subinterface on port GigabitEthernet2/1.
C. It means that port GigabitEthernet2/1 is assigned to VSAN 2.
D. It is a mistake in the interface configuration.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 45
Refer to the exhibit. What is the effect of executing the commands shown in the exhibit?
A. Host A will not be able to communicate with interface mgmtO. “Pass Any Exam. Any Time.” – www.actualtests.com 21 Cisco 642-359: Practice Exam
B. Host B will not be able to communicate with interface mgmtO.
C. All hosts will be able to communicate with interface mgmtO.
D. No hosts will be able to communicate with interface mgmtO.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 46
A host is unable to access the storage network after its HBA is replaced. Which of these switch configurations could be preventing access?
A. port-based zoning
B. port-mode security
C. port security
D. port VSAN membership
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 47
Which Cisco MDS feature can be used to notify an administrator or call center that a serious event has occurred in the fabric?
A. Call Home
B. syslog
C. FLOGI
D. SNMP
E. SPAN
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 48
Why would you use the fcanalyzer command?
A. to ensure that Fibre Channel configuration settings are synchronized across all switches in the fabric
B. to identify common configuration errors in the fabric
C. to nondisruptively capture and decode Fibre Channel control frames
D. to decode and analyze Fibre Channel frames and ordered sets on a link “Pass Any Exam. Any Time.” -www.actualtests.com 22 Cisco 642-359: Practice Exam
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 49
What is the recommended minimum clearance between chassis when installing the Cisco MDS 9500 Series in a standard telco rack?
A. 2.5 inches
B. 3 inches
C. 6 inches
D. 9 inches
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 50
Your company is planning a SAN deployment using Fibre Channel connections from a central, highly secure data center to several less secure branch offices. Which of these security features would allow you to disable all branch office switch management ports and yet still maintain the complete suite of TCP/IP-based SAN management utilities?
A. IPSec
B. Port Mode Security
C. Port Security
D. Overlay VSAN
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 51
What information does the command showflogi database provide?
A. verifies connectivity for attached devices
B. verifies that attached devices are in the correct zone
C. displays a list of the host ports that have logged into each storage port
D. displays fabric login errors
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 52
“Pass Any Exam. Any Time.” – www.actualtests.com 23
Cisco 642-359: Practice Exam
You have set up a session to the SD_Portto enable the investigation of a problem on a particular Fibre
Channel port. You need to check whether this has been correctly set up for the desired port.
Which command should you use?
A. show span session
B. showfcflow
C. showtlport
D. show fcanalyzer
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 53
Which feature detects hardware faults and attempts recovery actions?
A. Switch Health Analysis
B. Fabric Configuration Analysis
C. Online Health Management System
D. EnD.to-End Connectivity Analysis
E. Cisco Fabric Services
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 54
Hosti and Storagel are in VSAN 10 and have been communicating successfully. An administrator creates and activates an IVR zoneset enabling Hosti and Storage2 to communicate. Unexpectedly, after this new IVR zoneset is activated, Hosti loses connectivity with Storagel. “Pass Any Exam. Any Time.” – www.actualtests.com 24 Cisco 642-359: Practice Exam Why did this happen?
A. The default zone policy in VSAN 10 is set to permit.
B. The local zoneset distribution policy for VSAN 20 is set to allow.
C. The zoneset distribution policy for VSAN 10 is set to full.
D. Standard zones and IVR zones cannot coexist in the same VSAN.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 55
You are implementing an FCIP solution for SAN extension between two data centers using the Cisco MDS 9000 Series platform. For redundancy, there are two Metro Ethernet paths between the data centers. How can you specify primary and secondary paths for each FCIP tunnel?
A. Configure OSPF routing on the IPS-8. .
B. Configure EIGRP routing on the IPS-8.
C. Configure FSPF link costs on the MDS switch.
D. Configure QoS on the MDS switch.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
“Pass Any Exam. Any Time.” – www.actualtests.com 25 Cisco 642-359: Practice Exam
QUESTION 56
In order to allow access to a switch using Telnet, which three settings should be configured during the initial setup of a Cisco 9000 Series switch using SAN-OS Release 2.0? (Choose three.)
A. assign an admin password
B. accept auto for the switchport trunk mode
C. configure the IP address for the VSAN 1 interface
D. configure the netmask for the IP address
E. configure the IP address for the MgmtO interface F – Configure SSH with an RSA1 key
Correct Answer: ADE Section: (none) Explanation
Explanation/Reference:
QUESTION 57
What are four valid protocols for copying software to the MDS 9000 family switches? (Choose four.)
A. Remote Copy Service
B. Secure Copy Protocol
C. Trivial File Transfer Protocol
D. File Transfer Protocol
E. Secure Trivial File Transfer Protocol
F. Secure File Transfer Protocol
Correct Answer: BCDF Section: (none) Explanation
Explanation/Reference:
QUESTION 58
On a Class C IP network, how many bits in the IPv4 address are used to identify the network?
A. 8
B. 16
C. 24
D. 32
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 59
“Pass Any Exam. Any Time.” – www.actualtests.com 26 Cisco 642-359: Practice Exam
After performing the initial switch configuration by running the setup utility, an administrator notices that ports configured to connect to other Cisco MDS 9000 switches invariably come up as E_Ports rather than TE_Ports. Which error was made at initial configuration?
A. VSAN capabilities were not enabled.
B. Default switchport trunk mode was set to auto.
C. Full zoneset distribution was not enabled.
D. Default switchport trunk mode was set to on.
Correct Answer: B Section: (none)
Explanation Explanation/Reference:
QUESTION 60
Which three of these terms are valid Fibre Channel topologies? (Choose three.)
A. point-to-point
B. switched backbone
C. Gigabit Ethernet
D. arbitrated loop
E. switched fabric
F. autonomous region
Correct Answer: ADE Section: (none) Explanation
Explanation/Reference:
QUESTION 61
Which two Cisco MDS 9000 Series Switches are used in small- and medium-sized SAN topologies? (Choose two.)
Select 2 response(s).
A. Cisco MDS 9124
B. Cisco MDS 9222i
C. Cisco MDS 9506
D. Cisco MDS 9509
E. Cisco MDS 9513
Correct Answer: AB Section: (none) Explanation
Explanation/Reference:
“Pass Any Exam. Any Time.” – www.actualtests.com 27 Cisco 642-359: Practice Exam
QUESTION 62
Which second-generation Fibre Channel module offers a full 4Gb/s line rate on all ports? Select the best response.
A. 12-port 1/2/4 Gb/s Fibre Channel module
B. 24-port 1/2/4 Gb/s Fibre Channel module
C. 24-port 1/2/4/8 Gb/s Fibre Channel module
D. 48-port 1/2/4 Gb/s Fibre Channel module
Correct Answer: A Section: (none) Explanation
Explanation/Reference: QUESTION 63
Which Cisco MDS 9000 Series Switch has non-field-replaceable fans? Select the best response
A. Cisco MDS 9124
B. Cisco MDS 9134
C. Cisco MDS 9222i
D. Cisco MDS 9506
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 64
When using the Cisco MDS 9000 Switches, which protocol provides in-band management? Select the best response.
A. FCIP
B. IPFC
C. iSCSI
D. SNMP
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 65
What is a benefit of using the Cisco Fabric Manager Software Install Wizard instead of using the CLI-based software upgrade?
“Pass Any Exam. Any Time.” – www.actualtests.com 28 Cisco 642-359: Practice Exam
Select the best response.
A. can be used to upgrade multiple switches with a single procedure
B. shows the upgrade procedure progress
C. upgrades kickstart and system images in a single step
D. notifies when upgrade procedure has finished
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 66
A junior SAN engineer is asked to prepare the configuration for the NPV edge switch. The NPV edge switch will be connected to the NPV core switch via the fc 1/24 interface. The end device will be connected to the fc 1/1 interface and should be placed in VSAN 10. Which configuration for the NPV edge switch accomplishes this request?
Select the best response.
A. feature npv interface fcl/24 switchport mode F interface fcl/1 switchport mode F vsan database vsan 10 interface fcl/1 vsan 10 interface fcl/24 153373-15
B. feature npv interface fcl/24 switchport mode F interface fcl/1 switchport mode F vsan database vsan 10 interface fcl/1 vsan 10 interface fcl/24 153373-7
C. feature npv interface fcl/24 switchport mode F interface fcl/1 switchport mode F vsan database vsan 10 interface fcl/1 vsan 10 interface fcl/24 153373-3 “Pass Any Exam. Any Time.” – www.actualtests.com 29 Cisco 642-359: Practice Exam
D. feature npv interface fcl/24 switchport mode F interface fcl/1 switchport mode F vsan database vsan 10 interface fcl/1 vsan 10 interface fcl/24 153373-11
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 67
Which two options can be used to enable flex-attach when automatic assignment is used? (Choose two.) Select 2 response(s).
A. global across all NPV switches
B. global across all NPIV-enabled switches
C. per interface or interface range
D. per server WWN
E. per server FC-ID
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 68
Refer to the exhibit. When looking at the Cisco Fabric Manager, you notice that one of the switches has this symbol superimposed on it. What is the reason?
Select the best response.
A. The device is manageable but there are operational problems.
B. The device is online but not working properly.
C. The device is not manageable.
D. The device is Down.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
“Pass Any Exam. Any Time.” – www.actualtests.com 30 Cisco 642-359: Practice Exam
QUESTION 69
Which command can be used to determine whether device aliases in VSAN 5 are configured for fabric-wide distribution?
A. show fcalias distribution vsan 5
B. show cfs application name device-alias
C. show vsan 5 device-alias status
D. show vsan 5 device-alias status
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 70
Issuing the show role command to check a defined role in an MDS 9000 Series switch will produce the following output:
Role : Manage VSAN Description : vsan policy : deny Permitted vsans: 2-4
Rule Type Command-type Feature
1.
permit config *
2.
deny config fspf
3.
permit debug zone
4.
permit exec fcping
Which of the following two functions can a user with role Manage undertake? (Choose two.)
A. change fspf parameters
B. configure FC port parameters for VSAN 3
C. issue a debug command for a port
D. heck connectivity for VSAN 2
Correct Answer: BD Section: (none) Explanation Explanation/Reference:
With the products Cisco 642-359 for training and preparation of testing you would not only significantly reduce your fees, but pass your exam. We obtain our products from Authorities experts from test center.We give you the best path to successful completion of your exam to the real and original exam questions and answers for Cisco 642-359 .