Category: Cisco
Attention Please: Professional new version Cisco 642-359 PDF and VCE dumps can now free download on Cert4sure.net, all are updated timely by our experts covering all new questions and questions. 100 percent pass your Cisco 642-359 exam.
Exam A
QUESTION 1
While examining the output of a show run command on the Cisco MDS 9000 Series, you notice that the
statement interface GigabitEthernet2/12 appears in the output. What does this mean?
Select the best response.
A. It refers to the second FCIP tunnel that is configured on port GigabitEthernet2/1
B. It refers to a VLAN subinterface on port GigabitEthernet2/1
C. It means that port GigabitEthernet2/1 is assigned to VSAN 2
D. It is a mistake in the interface configuration.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 2
The HBA on your storage server only supports the NL_Port mode. Which interface type on the Cisco MDS 9000 Series fabric switches can support this HBA? Select the best response.
A. F
B. TE
C. FL
D. N
E. E
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 3
For purposes of granting restricted access to statically configure iSCSI virtual targets, which three of these can be used to identify iSCSI initiators? (Choose three.) Select 3 response(s).
A. iSCSI node name
B. host name
C. IPv4 address and subnet PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359
D. MAC address
E. IPv6 address
F. iSCSI WWN
Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:
QUESTION 4
What is a benefit of enhanced zoning? Select the best response.
A. fabric locked during configuration changes
B. larger zoning database size
C. database rollback in case of failure
D. zones allowed to span VSANs
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 5
How many ports are addressable on a fabric arbitrated loop? Select the best response.
A. 126
B. 127
C. 255
D. 256
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 6
Which three of the following are possible reasons why a line card module does not come online? (Choose
three.)
Select 3 response(s).
A. Port indexes have been taken offline.
B. Available port indexes are noncontiguous.
C. Not enough power is available in the chassis.
D. An invalid interoperability mode has been configured.
E. Unsupported SFPs have been installed.
F. Not enough port indexes are available.
Correct Answer: BCF Section: (none) Explanation
Explanation/Reference:
QUESTION 7
Which of the following tools would you use to view SCSI error count statistics?
PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359
Select the best response.
A. Cisco Performance Manager
B. RMON
C. Cisco Traffic Analyzer
D. Cisco Fabric Analyzer
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 8
Why would you use the fcanalyzer command? Select the best response.
A. to ensure that Fibre Channel configuration settings are synchronized across all switches in the fabric
B. to identify common configuration errors in the fabric
C. to nondisruptively capture and decode Fibre Channel control frames
D. to decode and analyze Fibre Channel frames and ordered sets on a link
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 9
Which two features help you verify connectivity between host and storage devices? (Choose two.) Select 2 response(s).
A. fcanalyzer
B. Cisco Traffic Analyzer
C. End-to-End Connectivity Analysis
D. Zone Merge Analysis
E. fcping
Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 10
Which feature detects hardware faults and attempts recovery actions? Select the best response.
A. Switch Health Analysis
B. Fabric Configuration Analysis
C. Online Health Management System
D. End-to-End Connectivity Analysis
E. Cisco Fabric Services PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 11
A customer has reported performance degradation in the SAN. The system administrator would like to track read-write I/O and LUN use on several devices. The devices are directly connected to various switches and belong to different VSANs. The administrator wants to gather information for the last 72
hours.
Which of the following Cisco MDS 9000 Series tools is needed to track SCSI I/O and LUN statistics?
Select the best response.
A. Cisco Fabric Manager
B. Cisco Traffic Analyzer and PAA
C. Cisco Performance Manager
D. Cisco Fabric Analyzer
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 12
Which services are supported by a Cisco NX-OS AAA configuration? Select the best response.
A. Telnet, SSH, FM and DM logins
B. Console login, FC-SP authentication, FTP
C. FC-SP authentication, FM and DM logins, TFTP
D. iSCSI authentication, FTP, FC-SP authentication
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 13
Which two Cisco MDS 9000 Series Switches are used in small- and medium-sized SAN topologies?
(Choose two.)
Select 2 response(s).
A. Cisco MDS 9124
B. Cisco MDS 9222i
C. Cisco MDS 9506
D. Cisco MDS 9509
E. Cisco MDS 9513
Correct Answer: AB Section: (none) Explanation
Explanation/Reference:
QUESTION 14
Which second-generation Fibre Channel module offers a full 4Gb/s line rate on all ports?
PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359
Select the best response.
A. 12-port 1/2/4 Gb/s Fibre Channel module
B. 24-port 1/2/4 Gb/s Fibre Channel module
C. 24-port 1/2/4/8 Gb/s Fibre Channel module D. 48-port 1/2/4 Gb/s Fibre Channel module
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 15
Which Cisco MDS 9000 Series Switch has non-field-replaceable fans? Select the best response.
A. Cisco MDS 9124
B. Cisco MDS 9134
C. Cisco MDS 9222i
D. Cisco MDS 9506
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 16
When using the Cisco MDS 9000 Switches, which protocol provides in-band management? Select the best response.
A. FCIP
B. IPFC
C. iSCSI
D. SNMP
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 17
What is a benefit of using the Cisco Fabric Manager Software Install Wizard instead of using the CLI-based software upgrade?
Select the best response.
A. can be used to upgrade multiple switches with a single procedure
B. shows the upgrade procedure progress
C. upgrades kickstart and system images in a single step
D. notifies when upgrade procedure has finished
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 18
PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359 A junior SAN engineer is asked to prepare the configuration for the NPV edge switch. The NPV edge switch will be connected to the NPV core switch via the fc 1/24 interface. The end device will be connected to the fc 1/1 interface and should be placed in VSAN 10 Which configuration for the NPV edge switch accomplishes this request? Select the best response.
153373-15
153373-7
153373-3
153373-11 PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359
Correct Answer: B Section: (none) Explanation Explanation/Reference:
QUESTION 19
Which two options can be used to enable flex-attach when automatic assignment is used? (Choose two.) Select 2 response(s).
A. global across all NPV switches
B. global across all NPIV-enabled switches
C. per interface or interface range
D. per server WWN
E. per server FC-ID
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 20
Refer to the exhibit. When looking at the Cisco Fabric Manager, you notice that one of the switches has this symbol superimposed on it. What is the reason? Select the best response.
A. The device is manageable but there are operational problems.
B. The device is online but not working properly.
C. The device is not manageable.
D. The device is down.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 21
What type of information can the Cisco Fabric Analyzer capture and decode? Select the best response.
A. data traffic within a specific VSAN
B. data traffic within all VSANs PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359
C. control traffic within the supervisor module only
D. control traffic from anywhere on a switch
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 22
As which two options can an RMON event manifest itself? (Choose two.) Select 2 response(s).
A. log entry
B. email message
C. SNMP trap
D. script action
E. alarm
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 23
Refer to the exhibit. The customer connects two switches for which the E_port does not come up. Which command should the administrator use to resolve the problem?
Select the best response.
A. mds(config)# fcdomain domain 3 static vsan 1 mds(config)# fcdomain restart disruptive vsan 1
B. mds(config)# fcdomain domain 3 static vsan 1 mds(config)# fcdomain restart vsan 1
C. mds(config-vsan-db)# fcdomain domain 3 static vsan 1 mds(config-vsan-db)# fcdomain restart disruptive vsan 1
D. mds(config-vsan-db)# fcdomain domain 3 static vsan 1 mds(config-vsan-db)# fcdomain restart vsan 1
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359
QUESTION 24
Refer to the exhibit. The customer wants to upgrade the Cisco MDS 9500 Switch. When they execute the install all command, this output is displayed. What will occur on the modules for which the upgrade’s impact was shown as disruptive? Select the best response.
A. The data flow through the switch will be corrupted and can disastrously affect data consistency.
B. The data flow will be interrupted, and the hosts should be shut down during the upgrade to prevent problems.
C. The data flow will be interrupted, and the applications should be put in the paused and consistent state during the upgrade.
D. The data flow will be paused. No intervention is necessary on the servers.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 25
Refer to the exhibit. The customer network has blue and red VSANs redundantly connected, Path A having a 4-ISL port channel and Path B having a 2-ISL port channel. Changes to the physical topology are not allowed for the next six months. All the traffic now flows over Path A with congestion occurring on both VSANs at peak times. The blue VSAN is, on the average, generating four times the amount of data than that of the red VSAN. How can the blue and red VSAN traffic be separated over the two paths, while preserving redundancy?
PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359 Select the best response.
A. Make a zone in the blue VSAN with only ISL ports on Path B, and make another zone in the red VSAN with only ISL ports on Path A.
B. Make a zone in the blue VSAN with only ISL ports on Path A, and make another zone in the red VSAN with only ISL ports on Path B.
C. In the blue VSAN, give Path B a lower FSPF cost than Path A; in the red VSAN, give Path A a lower FSPF cost than Path B.
D. In the blue VSAN, give Path A a lower FSPF cost than Path B; in the red VSAN, give Path B a lower FSPF cost than Path A.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 26
Which command would you use to configure Cisco Fabric Analyzer to display only SCSI-level protocol
traffic for the whole switch? The display needs to be output on the console.
Select the best response.
A. switch(config)# fcanalyzer local display-filter fcp_cmd
B. switch(config)# fcanalyzer display-filter fc_cmd
C. switch(config)# fcanalyzer local display-filter scsi
D. switch(config)# fcanalyzer local display-filter scsi_cmd
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359
QUESTION 27
Refer to the exhibit. The Cisco Device Manager screen shows multiple problems in a SAN environment. Which two problems are displayed? (Choose two.) Select 2 response(s).
A. The amount of RAM in the switch is running out.
B. The amount of NVRAM in the switch is running out.
C. Disk on port fc1/6 is at the limit of its receive bandwidth.
D. Port iscsi2/2 is misconfigured.
E. There is a problem with the CPU.
Correct Answer: BC Section: (none) Explanation
Explanation/Reference:
QUESTION 28
Refer to the exhibit. What alarm will be sent for this RMON event? 191837412jpg Select the best response.
A. FCIP link failure
B. Fibre Channel link down
C. Fibre Channel link failure
D. Fibre Channel link reestablishment
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 29
A customer has some performance problems in their SAN environment. They want to use a Cisco MDS
9000 Port Analyzer Adapter to connect to the Cisco MDS Switch to troubleshoot the performance
problems. Which two options need to be configured on the MDS Switch? (Choose two.)
Select 2 response(s).
PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359
A. Put the port into the proper zone that will be monitored.
B. Set the port speed to the value corresponding with the PAA setting.
C. Put the port in SD port mode.
D. Configure any port channel necessary.
E. Turn off flow control.
Correct Answer: BC Section: (none) Explanation
Explanation/Reference:
QUESTION 30
Refer to the exhibit. The customer’s ISL links are flapping and seem to go down every few days. While
troubleshooting the problem, they determine that the speed of failover to the redundant path is taking too
long. What is the recommended solution to the problem, involving turning on a feature?
Select the best response.
A. use port tracking
B. disable the flapping ISL
C. use port channel
D. adjust FSPF link costs
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 31
Which configuration will enable remote access management using Telnet? Select the best response.
A. interface mgmt0 ip address 10001 2552552550 remote-access enable PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359
B. interface mgmt0 ip address 10001 2552552550 feature telnet enable
C. interface mgmt0 ip address 10001 2552552550 telnet enable
D. interface mgmt0 ip address 10001 2552552550 telnet server enable
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 32
When large Fibre Channel frames must be sent from an MSM 18/4 module at the central site to the remote
offices, what is the consequence of disabling the Path MTU Discovery and using the default Ethernet
MTU?
Select the best response.
A. Packet shaping becomes effective.
B. Minimum retransmission interval is prolonged.
C. Jumbo frames are enabled.
D. Large Fibre Channel frames are fragmented.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 33
With regards to FCIP encapsulation, which statement is true? Select the best response.
A. The Fibre Channel frame is encapsulated into an IP packet.
B. The Fibre Channel frame is encapsulated into an MPLS packet.
C. The Fibre Channel frame is encapsulated into an Ethernet frame.
D. The Fibre Channel frame is encapsulated into an iSCSI packet.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 34
Which command enables connectivity to a management VSAN via 100010 IP gateway when IPFC in-band
management is used?
Select the best response.
A. ip route 0000 0000 100010
B. route 0/0 100010
C. default-gateway 100010
D. route add default 100010
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 35
Which command is used to configure VLAN 100 on the Gigabit Ethernet 2/1 interface through
PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359
which iSCSI-enabled servers should be connected to the Fibre Channel targets? Select the best response.
A. interface gigabitethernet 2/1100
B. interface gigabitethernet 2/1 vlan 100
C. interface gigabitethernet 2/1 encapsulation isl 100
D. interface gigabitethernet2/1 vlan 100
Correct Answer: A Section: (none) Explanation Explanation/Reference:
QUESTION 36
Which access control list configuration allows the IP traffic from the 10001 host to be moved to the
192168202 host only?
Select the best response.
A. ip access-list ACL1 permit ip 10001 0000 192168202 0000
B. access-list 10 permit host 10001 host 192168202
C. access-list ACL1 permit source host 10001 destination host 192168202
D. filter ACL permit host 10001 host 192168202
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 37
Refer to the exhibit. What would happen if one of the power supplies failed? Select the best response.
A. There would be no disruption regarding MDS operation. PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359
B. The MDS would shut down the standby supervisor to compensate for the power loss.
C. The MDS would reset the failed power supply in an attempt to resolve the problem.
D. Due to insufficient power, the MDS would shut down some modules.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 38
The customer wants to create and use custom-based reports to monitor the operation of the deployed MDS switches and the overall health of the SAN. Which option is required in order to use custom reports? Select the best response.
A. standalone Cisco Fabric Manager
B. Cisco Device Manager with Enterprise license installed
C. Cisco Fabric Manager Server with Cisco Performance Manager
D. PAA, SPAN, and protocol analyzer
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 39
If you have a brand new Cisco MDS Switch and you are using the initial setup routine, what information
must be entered?
Select the best response.
A. Admin password
B. Default switch port interface state
C. Management IP address
D. Login account
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 40
Refer to the exhibit. While troubleshooting, you clear the fc1/10 interface counters and reset the interface. What is the reason that interface fc1/10 is down?
PassGuide.com – Make You Succeed To Pass IT Exams PassGuide 642-359 Select the best response.
A. The interface speed is misconfigured.
B. The SFP is missing.
C. The fiber-optic cable’s transmit and receive pins are not correctly connected.
D. The peer switch uses a different interoperability mode.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
Cisco 642-359 Exam Certification Guide presents you with an organized test preparation routine through the use of proven series elements and techniques.“Do I Know This Already?”quizzes open each chapter and allow you to decide how much time you need to spend on each section.Cisco 642-359 lists and Foundation Summary tables make referencing easy and give you a quick refresher whenever you need it.Challenging Cisco 642-359 review questions help you assess your knowledge and reinforce key concepts.Cisco 642-359 exercises help you think about exam objectives in real-world situations, thus increasing recall during exam time.
New Updated Questions Where to find the newest Cisco 642-359 exam dumps? if you want to pass exam Cisco 642-359 without the second try, you should download the latest updated Cisco 642-359 braindump for preparing. Now visit Cert4sure.net to get free pdf study guide with valid Cisco 642-359 exam dumps and free vce dumps, which will help you passing quickly!
Exam A
QUESTION 1
Which command would you use to determine if device aliases in VSAN 5 are configured for fabriC.wide distribution?
A. show zoneset name alias vsan 5
B. show cfs application name device-alias
C. showfcalias distribution vsan 5
D. show vsan 5 device-alias status
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 2
DRAG DROP
Drop
Drag the Cisco analysis tool on the left to its appropriate description on the right.
Drag and drop question. Drag the items to the proper locations.
A. 1=3 , 2=2, 3=4, 4=3
B.
C.
D.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
“Pass Any Exam. Any Time.” – www.actualtests.com 2 Cisco 642-359: Practice Exam
Explanation:
QUESTION 3
The MDS 9000 family switches use what three technologies to protect against unauthorized management access? (Choose three.)
A. SNMPV3
B. SSH
C. RBAC
D. RMON
E. ses
F. WEBM
Correct Answer: ABC Section: (none) Explanation
Explanation/Reference:
“Pass Any Exam. Any Time.” – www.actualtests.com 3 Cisco 642-359: Practice Exam
QUESTION 4
What is a benefit of enhanced zoning?
A. fabric locked during configuration changes
B. larger zoning database size
C. database rollback in case of failure
D. zones allowed to span VSANs
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 5
Which two of these environments suggest the use of FCIP Write Acceleration? (Choose two.)
A. remote tape backup
B. Port Channel links between sites
C. applications that support multiple outstanding l/Os
D. fast network with minimal delays
E. DWDM links
Correct Answer: BC Section: (none) Explanation
Explanation/Reference:
QUESTION 6
Which three of the following are possible reasons why a line card module does not come online? (Choose three.)
A. Port indexes have been taken offline.
B. Available port indexes are noncontiguous.
C. Not enough power is available in the chassis.
D. An invalid interoperability mode has been configured.
E. Unsupported SFPs have been installed.
F. Not enough port indexes are available.
Correct Answer: BCF Section: (none) Explanation
Explanation/Reference:
QUESTION 7
Refer to the exhibit.
“Pass Any Exam. Any Time.” – www.actualtests.com 4 Cisco 642-359: Practice Exam
Which two options from the Tools menu would you select to verify connectivity and latency to a Fibre Channel end device? (Choose two.)
A. Switch Health
B. Fabric Configuration
C. End to End Connectivity
D. Ping
E. Device Manager
Correct Answer: CD Section: (none) Explanation
Explanation/Reference:
QUESTION 8
During initial switch configuration, the administrator elects to enable full zoneset distribution. What is the impact of this choice during zoneset activation?
A. only the active zoneset is distributed to all switches in the fabric
B. both the full zone database and active zoneset are distributed to all switches in the fabric
C. both FCID and WWN information are distributed to all switches in the fabric
D. only the full zone database is distributed to all switches in the fabric
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 9
You are asked to review the running configuration of a switch that a junior administrator has prepared to be placed in a heterogeneous SAN environment. This environment includes three different brands of Fibre Channel switches. In this particular environment, only VSAN 1 is being used.
“Pass Any Exam. Any Time.” – www.actualtests.com 5 Cisco 642-359: Practice Exam
Which of these attributes suggests that the switch has been incorrectly configured?
A. Astatic domain ID has been set to 0x21.
B. The srC.dst-ox load balancing has been selected.
C. Interop mode 1 has been selected.
D. FCC has been enabled.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 10
DRAG DROP
Drop
Drag the correct compression mode on the left to its appropriate bandwidth on the right.
Drag and drop question. Drag the items to the proper locations.
A. mode1=2 , mode2=3 , mode3=1 , auto=4
B.
C.
D.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
“Pass Any Exam. Any Time.” – www.actualtests.com 6 Cisco 642-359: Practice Exam
Explanation:
QUESTION 11
DRAG DROP
Drop
Click and drag each item on the left to its correct security description on the right.
Drag and drop question. Drag the items to the proper locations.
A. 1=6 , 2=2 , 3=3 , 4=5 , 5=4 , 6=1
B.
C.
D.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
“Pass Any Exam. Any Time.” – www.actualtests.com 7
QUESTION 12
When configuring FCIP, packet fragmentation should be avoided in order to achieve optimal throughput. Fragmentation can be avoided by knowing which of the following?
A. MTU of the source IP interface
B. largest MTU in the path
C. smallest MTU in the path
D. MTU of the destination IP interface
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 13
When configuring FCIP, packet fragmentation should be avoided in order to achieve optimal throughput. Fragmentation can be avoided by knowing which of the following?
A. MTU of the source IP interface
B. largest MTU in the path
C. smallest MTU in the path
D. MTU of the destination IP interface
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 14
For purposes of granting restricted access to statically configure iSCSI virtual targets, which three of these can be used to identify iSCSI initiators? (Choose three.)
“Pass Any Exam. Any Time.” – www.actualtests.com 8 Cisco 642-359: Practice Exam
A. iSCSI node name
B. hostname
C. IPv4 address and subnet
D. MAC address
E. IPv6 address
F. iSCSIWWN
Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:
QUESTION 15
You have been asked to convert three existing ISLs into a PortChannel as nondisruptively as possible.
Which approach will best accomplish this?
A. Place all three ISLs into a PortChannel, because PortChannel creation is a nondisruptive operation.
B. Convert the ISLs into an EISL and then place them into a PortChannel.
C. Place one link into a single-link PortChannel and then add the other two links to the PortChannel.
D. Ensure that the VSAN allowed lists on both ends of each link are identically configured, then create the three-link PortChannel.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 16
“Pass Any Exam. Any Time.” – www.actualtests.com 9 Cisco 642-359: Practice Exam
Which three statements describe automatically supported, basic zone features (no additional configuration required) in the Cisco MDS 9000 Family of switches? (Choose three.)
A. A VSAN contains the zone sets.
B. Zone reactivation can disrupt existing traffic.
C. A zone or zone set with the same name can exist in each VSAN.
D. Hard zoning can be disabled.
E. Active zone sets are preserved across switch reboots
F. Default zoning behavior is to distribute the Full Zone Database.
Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:
QUESTION 17
Which three options allow or enable nondisruptive upgrades? (Choose three.)
A. IPS module software upgrades
B. dual supervisor modules on a Cisco MDS 9500 Series switch
C. using the install-all command
D. upgrading the loader
E. installing a license F – using the reload command
Correct Answer: BCE Section: (none) Explanation
Explanation/Reference:
QUESTION 18
Which services are supported by a Cisco SAN-OS AAA configuration?
A. Telnet, SSH, FM and DM logins
B. console login, FC.SP authentication, FTP
C. FC.SP authentication, FM and DM logins, TFTP
D. iSCSI authentication, FTP, FC.SP authentication
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 19
How many ports are addressable on a fabric arbitrated loop?
A. 126 “Pass Any Exam. Any Time.” – www.actualtests.com 10 Cisco 642-359: Practice Exam
B. 127
C. 255
D. 256
Correct Answer: B Section: (none) Explanation Explanation/Reference:
QUESTION 20
A customer with multiple vendor switches establishes an ISL between a non-Cisco switch and an E_Port
on a Cisco MDS 9000 switch.
Which three statements are true about the interop behavior between the two switches? (Choose three.)
A. Exchange-based load balancing is supported in all interop modes.
B. Interop mode affects all VSANs.
C. Only E_Ports can be used to connect to non-Cisco MDS switches.
D. The non-Cisco switch must have matching FC timers with the VSAN containing the E_Port on the Cisco MDS 9000 Series switch.
E. Adding another ISL between the switches will allow a PortChannel to be configured for HA.
F. Interop mode 1 allows full featured communication between all combinations of MDS and non- MDS switches
Correct Answer: ACD Section: (none) Explanation
Explanation/Reference:
QUESTION 21
Which license is required on switches that are going to implement LUN zoning?
A. Storage Services Enabler
B. Enterprise license
C. Fabric Manager Server license
D. SAN Extension over IP license
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 22
DRAG DROP
Drop
Match the definition on the left with its appropriate word or phrase about switch interoperability on the right.
“Pass Any Exam. Any Time.” – www.actualtests.com 11
Cisco 642-359: Practice Exam
Drag and drop question. Drag the items to the proper locations.
A. 1=2, 2=1, 3=4, 4=5, 5=3
B.
C.
D.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
Explanation:
“Pass Any Exam. Any Time.” – www.actualtests.com 12 Cisco 642-359: Practice Exam
QUESTION 23
Which two of these logging statements are true? (Choose two.)
A. Call Home message level 0 is most urgent and level 7 is least urgent, whereas the syslog level 9 is most urgent and level 0 is least urgent.
B. Syslog message level 0 is most urgent and level 7 is least urgent, whereas the Call Home message level 9 is most urgent and level 0 is least urgent,
C. Syslog message level 7 is most urgent and level 0 is least urgent, whereas the Call Home message level 9 is most urgent and level 0 is least urgent.
D. Accounting logs can be stored locally and sent to remote AAA servers.
E. Go to logs > syslog > setup in Device Manager to view the local accounting log.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 24
Which of these Cisco Fabric Manager debugging tools can compare the current configuration with a previously saved configuration file?
A. Switch Health Analysis
B. Fabric Configuration Analysis
C. EnD.to-End Connectivity Analysis
D. Zone Merge Analysis
Correct Answer: B Section: (none) Explanation Explanation/Reference:
QUESTION 25
Choose the correct list of tasks to configure Remote Spanning.
A. Create a VSAN interface. Enable a Fibre Channel tunnel. Initiate the Fibre Channel tunnel. Configure the ST_Port in the source switch. Configure the SD_Port in the destination switch. Configure a SPAN session in the source switch.
B. Create a VSAN interface. Enable a Fibre Channel tunnel. Initiate the Fibre Channel tunnel. Configure the ST_Port in the source switch. Configure the SD_Port in the destination switch. Configure an RSPAN session in the source switch.
C. Create an RSPAN interface. Enable a Fibre Channel tunnel. Initiate the Fibre Channel tunnel. Configure the SD_Port in the destination switch. Configure the ST_Port in the source switch. Configure an RSPAN session in the source switch.
D. Create a VSAN interface. Enable a Fibre Channel tunnel. Initiate the Fibre Channel tunnel. Configure the ST_Port in the destination switch. Configure the SD_Port in the source switch. “Pass Any Exam. Any Time.” – www.actualtests.com 13 Cisco 642-359: Practice Exam Configure an RSPAN session in the source switch.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 26
When creating an Inter-VSAN routing topology, which type of World Wide Name (WWN) must be used?
A. Port WWN
B. Switch WWN
C. Fabric Port WWN
D. VSAN WWN
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 27
Your company has a multiswitch fabric including Switch A and Switch B. An administrator of Switch A creates the following zone set and successfully activates it: zoneset name ZoneSetl vsan 1 zone name Zonel vsan 1 pwwn 21:01:00:e0:8b:3c:03:b6 pwwn 21:01:00:e0:8b:3c:55:bb Later in the day, a second administrator creates the following zone set on Switch B: zoneset name ZoneSet2 vsan 1 zone name Zonel vsan 1 pwwn 21:01:00:e0:8b:3c:03:b6 pwwn 21:01:00:e0:8b:3c:55:aa What happens when the administrator of Switch B attempts to activate ZoneSet2?
A. ZoneSet2 becomes the active zone set for both Switches A and
B.
C. The fabric segments and ZoneSet2 become the active zone set for Switch B only.
D. The fabric segments and ZoneSet2 become the active zone set for Switch A only.
E. The fabric segments and ZoneSetl remain the active zone set for Switch B, while ZoneSet2 becomes the active zone set for Switch A.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 28
“Pass Any Exam. Any Time.” – www.actualtests.com 14 Cisco 642-359: Practice Exam
You have been asked to configure a port on your Cisco MDS switch so that a host can join your fabric. Which of these switch port types should the port be set to?
A. N_Port
B. NL_Port
C. F_Port
D. E_Port
E. TE_Port
F. SD Port
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 29
DRAG DROP
Drop The IT director wants to standardize the process that the SAN team follows when troubleshooting the SAN. IT director wants to leverage the tools that are provided by Cisco Fabric Manager so that each member of the team executes the samesteps when faced with a problem in the SAN. Click and drag the Cisco Fabric Manager troubleshooting tool to the purpose it serves in the repair strategy.
Drag and drop question. Drag the items to the proper locations.
A. 1=2, 2=4, 3=3, 4=1
B.
C.
D.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
“Pass Any Exam. Any Time.” – www.actualtests.com 15 Cisco 642-359: Practice Exam
Explanation:
QUESTION 30
Which of the following tools would you use to view SCSI error count statistics?
A. Cisco Performance Manager
B. RMON
C. Cisco Traffic Analyzer
D. Cisco Fabric Analyzer
Correct Answer: C Section: (none)
Explanation
Explanation/Reference:
QUESTION 31
A customer would like to implement a low-cost traffic engineering solution that provides a primary data path, and a secondary data path that will only be used in the event of a failure in the primary path. Which of these solutions best meets the customer needs?
A. VSAN allowed list pruning
B. FCC
C. QoS “Pass Any Exam. Any Time.” – www.actualtests.com 16 Cisco 642-359: Practice Exam
D. FSPF link costs
E. VOQ
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 32
The output from the switch show interface command indicates that the link from a host comes up as an FL_Port. The switch port is configured as auto. Which three of these HBA configurations could cause this scenario? (Choose three.)
A. the HBA is configured as an N_Port
B. the HBA is configured as an NL_Port
C. the HBA supports only NL mode
D. the HBA is configured as a TE_Port
E. the HBA supports only FC.AL technology
F. the HBA is configured as an TL_Port
Correct Answer: BCE Section: (none) Explanation
Explanation/Reference:
QUESTION 33
Refer to the exhibit. Which of the following statements is true?
A. All users belonging to the sangroup role are allowed to perform all configuration commands except fspf commands because the deny config feature fspf is listed first.
B. All users are allowed to perform all configuration commands because the permit config command is listed last and that will globally override all other rules.
C. All users belonging to the sangroup role to perform all configuration commands except fspf commands because it does not matter what order the rules are entered.
D. The configuration is not valid because rules are entered at the switch (config-role-vsan)# level.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 34
Which three types of network statistics can be captured with the Cisco Traffic Analyzer? (Choose three.)
“Pass Any Exam. Any Time.” – www.actualtests.com 17 Cisco 642-359: Practice Exam
A. historical reporting
B. total bandwidth used
C. Tx/Rx bandwidth per VSAN
D. Tx/Rx bandwidth per N_Port
E. class-based traffic breakdown
Correct Answer: BCD Section: (none) Explanation
Explanation/Reference:
QUESTION 35
Which two security protocols are supported in the Cisco iSCSI implementation? (Choose two.)
A. IPSec
B. FC.SP
C. SLAP
D. CHAP
E. PAP
Correct Answer: AD Section: (none) Explanation
The Cert4sure contains more than 400 practice questions for the Cisco 642-359 exams, including simulation-based questions. Also contains hands-on exercises and a customized copy of the Cisco 642-359 exams network simulation software.
100% Valid And Pass With latest Cisco 642-359 exam dumps, you will never fail your Cisco 642-359 exam. All the questions and answers are updated and added to the new version timely by our experts. Also now Cert4sure is offering free Cisco 642-359 exam VCE player and PDF files for free on their website.
Exam A
QUESTION 1
Issuing the show role command to check a defined role in an MDS 9000 Series switch will produce the following output: Role: Manage VSAN Description: Vsanpolicy: deny Permitted vsans: 2-4 Rule Type Command-type Feature 1- permit config * 2- deny config fspf 3- permit debug zone 4- permit exec fcping
Which of the following two functions can a user with role Manage undertake? (Choose two.)
A. check connectivity for VSAN 2
B. issue a debug command for a port
C. configure FC port parameters for VSAN 3
D. changefspf parameters
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 2
Which two options can be used to enable flex-attach when automatic assignment is used?
(Choose two.)
Select 2 response(s).
A. global across all NPV switches
B. per server WWN
C. per server FC-ID
D. per interface or interface range
E. global across all NPIV-enabled switches
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 3
Match the definition on the left with its appropriate word or phrase about switch interoperability on the right.
A. 1,2,3,4,5
B. 2,1,3,4,5
C. 3,1,2,4,5
D. 2,3,4,5,1
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 4
When using the Cisco MDS 9000 Switches, which protocol provides in-band management? Select the best response.
A. SNMP
B. IPFC
C. FCIP
D. iSCSI
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 5
What information does the command showflogi database provide?
A. verifies connectivity for attached devices
B. displays fabric login errors
C. displays a list of the host ports that have logged into each storage port
D. verifies that attached devices are in the correct zone
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 6
You have set up a session to the SD_Portto enable the investigation of a problem on a particular Fibre Channel port. You need to check whether this has been correctly set up for the desired port. Which command should you use?
A. showfcanalyzer
B. show span session
C. showfcflow
D. showtlport
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 7
A host is unable to access the storage network after its HBA is replaced. Which of these switch configurations could be preventing access?
A. port-mode security
B. port VSAN membership
C. port-based zoning
D. port security
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 8
Which command would you use to determine if device aliases in VSAN 5 are configured for fabriC.wide distribution?
A. showcfs application name device-alias
B. showvsan 5 device-alias status
C. showzoneset name alias vsan 5
D. showfcalias distribution vsan 5
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 9
Which feature requires the Cisco MDS 9000 Series Enterprise license?
A. centralized AAA services
B. port security
C. virtual output queues
D. PortChannels
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 10
What is the recommended minimum clearance between chassis when installing the Cisco MDS 9500 Series in a standard telco rack?
A. 2.5 inches
B. 9 inches
C. 3 inches
D. 6 inches
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 11
You work as a network administrator for Company.com. You study the exhibit carefully. When
looking at the Cisco Fabric Manager, you notice that one of the switches has this symbol
superimposed on it. What is the reason?
Exhibit:
Select the best response.
A. The device is down.
B. The device is manageable but there are operational problems.
C. The device is not manageable.
D. The device is online but not working properly.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 12
You work as a network administrator for Company.com. You study the exhibit carefully. Which of
the following statements is true?
Exhibit:
A. All users belonging to thesangroup role to perform all configuration commands except fspf commands because it does not matter what order the rules are entered.
B. All users belonging to thesangroup role are allowed to perform all configuration commands except fspf commands because the deny config feature fspf is listed first.
C. All users are allowed to perform all configuration commands because the permitconfig command is listed last and that will globally override all other rules.
D. The configuration is not valid because rules are entered at the switch (config-role-vsan)# level.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 13
Which of the following tools would you use to view SCSI error count statistics?
A. RMON
B. Cisco Fabric Analyzer
C. Cisco Traffic Analyzer
D. Cisco Performance Manager
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 14
Which two security protocols are supported in the Cisco iSCSI implementation? (Choose two.)
A. SLAP
B. CHAP
C. IPSec
D. PAP
E. FC.SP
Correct Answer: BC Section: (none) Explanation Explanation/Reference:
QUESTION 15
While examining the output of a show run command on the Cisco MDS 9000 Series, you notice that the statement interface GigabitEthernet2/2 appears in the output. What does this mean?
A. It refers to the second FCIP tunnel that is configured on port GigabitEthernet2/1.
B. It refers to a VLAN subinterface on port GigabitEthernet2/1.
C. It means that port GigabitEthernet2/1 is assigned to VSAN 2.
D. It is a mistake in the interface configuration.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 16
What is a benefit of enhanced zoning?
A. fabric locked during configuration changes
B. larger zoning database size
C. database rollback in case of failure
D. zones allowed to span VSANs
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 17
While examining the output of a show run command on the CiscoMDS9000Series, you notice that the statement interface GigabitEthernet2/1.2 appears in the output. What does this mean?
A. It refers to these condFCIP tunnel that is configured on port GigabitEthernet2/1.
B. It refers to a VLAN subinterface on port GigabitEthernet2/1.
C. It means that port GigabitEthernet2/1is assigned to VSAN2.
D. It is a mistake in the interface configuration.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 18
The HBA on your storage server only supports the NL_Port mode. Which interface type on the Cisco MDS9000Series fabrics witches can support this HBA?
A. F
B. TE
C. FL
D. N E. E
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 19
For purposes of granting restricted access to statically configure iSCSI virtual targets, which three of these can be used to identify iSCSI initiators?(Choose three.)
A. iSCS Inodename
B. hostname
C. IPv4 address and subnet
D. MAC address
E. IPv6 address
F. iSCSI WWN
Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:
QUESTION 20
What is a benefit of enhanced zoning?
A. fabriclockedduringconfigurationchanges
B. largerzoningdatabasesize
C. databaserollbackincaseoffailure
D. zonesallowedtospanVSANs
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
CCNA Exam Certification Guide is a best-of-breed Cisco 642-359 exam study guide that has been completely updated to focus specifically on the objectives.Senior instructor and best-selling author Wendell Odom shares preparation hints and Cisco 642-359 tips to help you identify areas of weakness and improve both your conceptual and hands-on knowledge.Cisco 642-359 Material is presented in a concise manner, focusing on increasing your understanding and retention of exam topics.
Cisco 642-176 contains a powerful new testing engine that allows you to focus on individual topic areas or take complete, timed exams from Cisco 642-176.The assessment engine also tracks your performance and presents feedback on a module-by-module basis, providing question-by-question Cisco 642-176 to the text and laying out a complete study plan for review.Cisco 642-176 also includes a wealth of hands-on practice exercises and a copy of the Cisco 642-176 network simulation software that allows you to practice your Cisco 642-176 hands-on skills in a virtual lab environment.The Cisco 642-176 supporting website keeps you fully informed of any exam changes
Exam A QUESTION 1
Exhibit:
You work as a network technician at Certkiller .com. Please study the exhibit carefully. Which three of these are accurate description of values that you will find in the verified column for different types of products? ( Choose three.)
A. If the solution is configured and orderable, a check mark will be displayed.
B. If the configuration is incomplete, the words “Not Configured” will be displayed
C. If the part is a non-configurable part, the words “Not configurable” will be displayed
D. If the solution is not orderable, a check mark will be displayed
E. If the configuration is complete, the word Done will be displayed
F. If the solution is not configured, a check mark will be displayed
Correct Answer: ABC Section: (none) Explanation
Explanation/Reference:
QUESTION 2
Which routing method is used to determine the forwarding paths for IP traffic in a Secure Cisco Single-Site Network foundation solution with remote teleworkers?
A. RIP
B. EIGRP
C. OSPF
D. Static and default routes
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 3
Exhibit:
You work as a network technician at Certkiller .com. Please study the exhibit carefully. In a Cisco Single-
Site Secure Network foundation implementation, which factors affect the router configuration you select?
Exhibit: image027.jpg
A. Maximum number of supported IP Phones per platform
B. Type of security scheme that is to be implemented
C. Maximum Amount of packet latency acceptable
D. Type of QoS scheme hat is being used
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 4
DRAG DROP
You work as a network technician at Certkiller .com. Your boss, Mrs. Certkiller, is interested in WAN
Services.
Match the appropriate WAN Services with the correct service type.
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference: QUESTION 5
The recommended WAN Access method for a simplified and cost effective Cisco Single-site Secure Network Foundation Deployment provides which type of Service?
A. Low Latency
B. Best-Effort
C. Guaranteed Quality
D. Guaranteed Bandwidth
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 6
You are designing a solution that needs to support 30 IP phone users. Which switch model and how many switches does the Cisco Single-Site Secure Network Foundation1.1 Desing and Implementation Guide suggest for the solution?
A. 1 Catalyst Express 500G-12TC,1 Catalyst 3750G-12S-S
B. 1 Catalyst 3750G-12S-S, 1 Catalyst Express 500-24PC
C. 2 Catalyst Express 500G-12TC
D. 1 Catalyst 3750G-12S-S, 1 Catalyst Express 500-24PC
E. 2 Catalyst Express 500-24PC
F. 2 Catalyst 3750G-12S-S
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 7
Exhibit: You work as a network technician at Certkiller .com. Please study the exhibit carefully. All of the computing devices shown are on the same logical network, as if they were all connected to the same switch. Which two features make this possible? ( Choose two.)
A. PAT
B. 802.1Q
C. Spanning-tree
D. VLANs
E. QoS
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 8
If voice and data traffic will be sent and received via a WAN links, what must be configured to provide a certain amount of dedicated bandwidth and to prioritize the voice traffic over other types of network traffic?
A. IPSec VPN
B. QoS mechanism
C. Firewall
D. NAT
E. EIGRP routing protocol
F. Static routing
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
Cisco 642-176 Interconnecting Cisco Networking Devices Part 1 (ICND1) exam is the exam associated with the Cisco Certified Entry Network Technician (CCENT) certification and is a tangible first step in achieving an Associate-level certification Candidates can prepare for this exam by taking the Interconnecting Cisco Networking Devices Part 1 (ICND1) course. This exam tests a candidate’s knowledge and skills required to successfully install, operate, and troubleshoot a small branch office network. The exam includes topics on the operation of IP data networks, LAN switching technologies, IPv6, IP routing technologies, IP services (DHCP, NAT, ACLs), network device security, and basic troubleshooting
QUESTION 9
DRAG DROP
You work as a network technician at Certkiller .com. Your boss, Mrs. Certkiller, is interested in UTP
categories.
Match the appropriate environments with the correct UTP category.
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference: QUESTION 10
You are designing a solution that needs to support a full-rate T3 connection. Which router model does the Cisco Single-Site Secure Network Foundation 1.1 Design and Implementation Guide suggest for this solution?
A. Cisco 2821
B. Cisco 2811
C. Cisco 3845
D. Cisco 2801
E. Cisco 2851
F. Cisco 3825
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 11
When resetting a Catalyst Express switch to factory default settings, which three options are available from the Software Recovery window? (Choose three.)
A. Boot to a password recovery window
B. Boot with the factory default image
C. Erase the system configuration and boot with the factory default IOS image
D. Erase the system configuration and boot from a TFTP-supplied IOS image
E. Erase the System Configuration
Correct Answer: BCE Section: (none) Explanation
Explanation/Reference: QUESTION 12
Which statement correctly describes network security settings in Cisco Network Assistant for the Catalyst Express 500 Switch?
A. The LOW setting enables broadcast storm control, but has no effect on the number of devices that can connect to a switch port
B. The LOW setting enables broadcast storm control and limits the number of devices that can connect to a switch port.
C. The LOW setting disables broadcast storm control but limits the number of devices that can connect to a switch port
D. The default network setting is “HIGH”
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 13
In an environment in which multiple VLANs have been defined on Catalyst Express 500 switches, which two statements are correct for ports that have been configured with the Smartport role of “IP Phone + Desktop”? (Choose two.)
A. The names of the VLANs used by the SmartPorts are case insensitive
B. The ports may belong to a configurable data VLAN
C. The names of the VLANs used by the Smartports are not relevant
D. The ports may belong to many VLANs, depending on how many PCs are connected to each port.
E. The names of the VLANs used by the Smartports are case sensitive
Correct Answer: BE Section: (none) Explanation
Explanation/Reference:
QUESTION 14
DRAG DROP You work as a network technician at Certkiller .com. Your boss, Mrs. Certkiller, is interested in SMB wireless solutions. You are required to produce the correct order for performing a Technology Strategy Development. Choose only steps that apply.
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 15
Exhibit: You work as a network technician at Certkiller .com. Please study the exhibit carefully. Which Cisco SDM Configuration task would you use to enable access and inspection rules on the WAN interface, preventing any external traffic from entering the network unless that traffic is a reply to a session that originated in the internal network?
A. Additional Task
B. Interface and Connections
C. Routing
D. NAT
E. Firewall and ACL
F. VPN
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 16
When enabling IPS on an ISR using the Cisco SDM IPS Wizard, in what location can the SDF be placed?
A. On the RAM of the ISR
B. On the USB memory stick of the ISR
C. On the NVRAM of the ISR
D. On the IPS Module of the ISR E. On the Flash memory of the ISR
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 17
During which phase of the Steps to Success methodology for Cisco SMB Security Solutions would the Security Technology Requirements document be used to determine a customer’s security requirements?
A. Perform
B. Position
C. Develop
D. Prepare
E. Plan
F. Design
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 18
Exhibit:
You work as a network technician at Certkiller .com. Please study the exhibit carefully. The exhibit is an example of which technology being implemented?
A. Spanning-tree
B. 802.1Q
C. VLANs
D. PAT
E. QoS
Correct Answer: D Section: (none)
Explanation
Explanation/Reference: QUESTION 19
Exhibit:
You work as a network technician at Certkiller .com. Please study the exhibit carefully. Which two statements correctly identify the reasons why there is only one static route and there are no dynamic protocols for the configuration shown?(Choose two.)
A. The configuration has not been completed yet on the router
B. There is only one entry and exit path to the service provider, so one static route is sufficient
C. The LAN functions at L3, so dynamic routing does not need to be enabled
D. Switch Agg 1 and R1 have not achieved L3 adjacency yet, thus whatever routing protocol has been configuration on R1 is not completely up
E. There is only one L3 device, thus dynamic routing is not needed
Correct Answer: BE Section: (none) Explanation
Explanation/Reference:
QUESTION 20
During which phase of the steps to success methodology for Cisco SMB security solutions would the Network Readiness Assessment be used to assess the readiness of an existing network infrastructure and determine which, if any, modification should be made prior to implementation?
A. Position
B. Prepare
C. Design
D. Perform
E. Plan
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 21
When determining a customer’s security requirements using the security site survey from the steps for success methodology, which three of theses should be included in the customer’s security policy and procedures? (Choose three.)
A. Third-party due diligence policy review
B. Remote Access Policy
C. Encryption Policy
D. Application change control policy
E. Security Personnel policy
Correct Answer: ABD Section: (none) Explanation
Explanation/Reference:
QUESTION 22
DRAG DROP You work as a network technician at Certkiller .com. Your boss, Mrs. Certkiller, is interested network security mechanisms. You are required to match the correct mechanism with the proper description.
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference: QUESTION 23
DRAG DROP You work as a network technician at Certkiller .com. Your boss, Mrs. Certkiller, is interested Success Methodology phases steps. You are required to produce the correct in which the appropriate phases takes place Use only steps that apply.
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 24
When using the steps to success methodology, where does Quote Builder fit into the deal process flow?
A. It encompasses the validate and solve steps
B. It encompasses the Discovery, Validate and Solve steps
C. It encompasses the Discover, Validate, Solve and Present Steps
D. It encompasses the Discovery, Solve and Close steps
E. It encompasses the Discovery, Validate and Present Steps
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 25
Which three of these pre-requisite for resetting a Catalyst Express 500 switch when Cisco Network Assistant is unavailable? (Choose three.)
A. At Least one enabled switch port that is unconnected to any device
B. A PC pre-configured with a specific IP Address and Mask
C. A PC or laptop with Windows 2000 or Windows XP installed and a web browser that has Java Script enabled
D. Physical Access to Switch
E. A Switch with no connected devices
Correct Answer: ACD Section: (none) Explanation
Explanation/Reference:
QUESTION 26
To protect the network from external and internal threats, where should Cisco IPS be enabled on an ISR?
A. Globally on the ISR
B. On the Console and Auxiliary Ports of the ISR
C. On the untrusted (Outside) interface of the ISR
D. On the trusted (Inside) interface of the ISR
E. On the WAN and LAN interfaces of the ISR
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 27
Which two WAN access methods are specified for a simplified and cost-effective Cisco Single-Site Secure Network Foundation Deployment Design? (Choose two.)
A. Frame-Relay
B. Leased Line
C. MPLS
D. DSL
E. Cable
F. Wireless
Correct Answer: DE Section: (none) Explanation
Explanation/Reference:
QUESTION 28
DRAG DROP
You work as a network technician at Certkiller .com. Your boss, Mrs. Certkiller, is interested in WAN
devices.
Match the appropriate WAN device with the correct description.
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 29
DRAG DROP
You work as a network technician at Certkiller .com. Your boss, Mrs. Certkiller, is interested in port types.
Match the appropriate port type with the correct function.
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference: QUESTION 30
During which phase of the steps to success methodology for Cisco SMB Security Solutions would the Network Readiness Assessment be used to assess the readiness of an existing network infrastructure and determine which, if any modification should be prior to implementation?
A. Prepare
B. Design
C. Position
D. Develop
E. Plan
F. Perform
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 31
Exhibit.
Please study the exhibit.
Which Cisco SDM configuration task is used to enable the translation of the inside network private IP
address to the public IP address?
A. Firewall and ACL
B. NAT
C. Routing
D. Interface and connections
E. VPN
F. Security Audit
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 32
Please study the exhibit.
What are two options available when using the Security Audit Configuration task in Cisco SDM? ( Choose two.)
A. Perform a One-step lockdown on the Router
B. Perform a Virus Scan
C. Perform a Secure audit on the Router
D. Perform a Denial Of Service attack on the Router to verify that it is protected
E. Perform a real-time inspection of incoming traffic destined for the router
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 33
When determining a customer’s technical requirements for a Cisco Unified Communications solution, which important tool can be used to determine the bandwidth used by different codecs with various protocols over different media?
A. Network Codec Aggregator Tool
B. Bandwidth Estimator Tool
C. Unified Communication Bandwidth Tool
D. Voice Bandwidth Calculator
E. Voice Codec Bandwidth Calculator
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 34
Exhibit:
You work as a network technician at Certkiller .com. Please study the exhibit carefully. What does “locking Down” the router entail?
A. Disabling HTTPS access to Cisco SDM
B. Prohibiting console access to Router
C. Preventing any alterations to the router’s running configuration
D. Disabling all vulnerable Services on the Router
E. Shutting down all the router’s interfaces
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 35
Your Customer has 21 users, each requiring both PC and IP Phone connectivity. Which is the correct configuration for this customer?
A. 1 Cisco 2811 ISR, 1 Catalyst Express 500G-12TC, 2 Catalyst Express 500-24PC
B. 1 Cisco 2851 ISR, Catalyst Express 500G-12TC, 3 catalyst Express 500-24PC
C. 1 Cisco 2821 ISR, Catalyst Express 500G-12TC, 2 Catalyst Express 500-24PC
D. 1 Cisco 2801 ISR, 1 Catalyst Express 500-24PC
Correct Answer: D Section: (none) Explanation
Explanation/Reference: QUESTION 36
When using Cisco Network Assistant to configure a WS-CE500-24LC switch, which three are available choices in the port settings window? (Choose three.)
A. Duplex mode selections
B. Auto MDIX selections
C. Status Selections
D. Group mode selections
E. Port security selections
Correct Answer: ABC Section: (none) Explanation
Explanation/Reference:
QUESTION 37
Which statements describes the remote sites in a Cisco Single-Site Secure Network Foundation solution with remote teleworkers?
A. They are separate from the central site and use NAT to route through the Internet to the Central Site
B. They are part of the VLANs at the Central Site; they are in the same subnets
C. They use public IP Addresses that are routable through the Internet
D. They are in separate subnets but are part of the private address space of the network
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 38
Which two statements about 802.1Q trunking in Secure Network Foundation Design Guide for Single Site Deployments are correct?
A. The Cisco Control VLAN carries only Layer 2 control traffic
B. 802.1Q trunking is used between the access switch and the router
C. There is no 802.1Q trunking used in these designs
D. When 802.1Q trunks are configured, they are also called Native VLANs
E. Trunking Ensures that traffic from only one VLAN is carried on that trunk
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 39
Exhibit: You work as a network technician at Certkiller .com. Please study the exhibit carefully. Which Cisco SDM configuration task would you select to configure a static route to the Service Provider?
A. NAC
B. Routing
C. Intrusion Protection
D. Quality Of Service
E. NAT
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 40
Which WAN connection requires a different interface than the standard interface provided in the Cisco Single-Site Secure Network Foundation deployment design?
A. Metro Ethernet
B. DSL
C. VPN
D. Cable
E. Frame-Relay
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
CCNA Cisco 642-176 Exam Certification Guide is part of a recommended study program from Cisco 642-176 that includes simulation and hands-on training from authorized Cisco 642-176 Learning Partners and self-study products from Cisco 642-176.Find out more about instructor-led, e-learning, and hands-on instruction offered by authorized Cisco 642-176 Learning Partners worldwide
This volume is part of the Exam Certification Guide Series from Cisco 642-176.Cisco 642-176 in this series provide officially developed exam preparation materials that offer assessment, review, and practice to help Cisco 642-176 Certification candidates identify weaknesses, concentrate their study efforts, and enhance their confidence as Cisco 642-176 exam day nears.
Exam A
QUESTION 1
Refer to the exhibit. What could be possible causes for the “Serial0/0 is down” interface status? (Choose two.)
A. A Layer 1 problem exists.
B. The bandwidth is set too low.
C. A protocol mismatch exists
D. An incorrect cable is being used.
E. There is an incorrect IP address on the Serial 0/0 interface.
Correct Answer: AD
QUESTION 2
Before installing a new, upgraded version of the IOS, what should be checked on the router, and which command should be used to gather this information? (Choose two.)
A. the amount of available ROM
B. the amount of available flash and RAM memory
C. the version of the bootstrap software present on the router
D. show version
E. show processes
F. show running-config
Correct Answer: BD
QUESTION 3
Refer to the exhibit. Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two.)
A. Host E and host F use the same IP gateway address.
B. Router1 and Switch2 should be connected via a crossover cable.
C. Router1 will not play a role in communications between host A and host D.
D. The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.
E. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.
F. The FastEthernet 0/0 interface on Router1 and Switch2 trunk ports must be configured using the same encapsulation type.
Correct Answer: DF
QUESTION 4
Refer to the exhibit. Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)
“Everything is under control” – www.pass4sure.com 3
A. It ensures that data will be forwarded by RouterB.
B. It provides stability for the OSPF process on RouterB.
C. It specifies that the router ID for RouterB should be 10.0.0.1.
D. It decreases the metric for routes that are advertised from RouterB.
E. It indicates that RouterB should be elected the DR for the LAN.
Correct Answer: BC
QUESTION 5
If you are a network administrator, how will you explain VTP configuration to a new technician? (Choose three.)
A. In the VTP client mode, a switch is unable to update its local VLAN database.
B. Configure a trunk link between the switches to forward VTP updates.
C. In the VTP server mode, a switch is able to update a switch in the VTP transparent mode.
D. In the VTP transparent mode, a switch will forward the received updates to other switches.
E. A switch in the VTP server mode only updates switches in the VTP client mode that have a higher VTP revision number.
F. A switch in the VTP server mode will update switches in the VTP client mode regardless of the configured VTP domain membership.
Correct Answer: ABD
QUESTION 6
Cisco IOS (originally Internetwork Operating System) is the software used on the vast majority of Cisco Systems routers and all current Cisco network switches. Which two of the following devices could you configure as a source for the IOS image in the boot system command? (Choose two.)
A. RAM
B. NVRAM
C. flash memory
D. HTTP server
E. TFTP server
F. Telnet server
Correct Answer: CE
CCNA Composite Exam:Cisco 642-176 CCNAX is the composite exam associated with the Cisco CCNA Routing and Switching certification. Candidates can prepare for this exam by taking the Interconnecting Cisco Networking Devices: Accelerated (CCNAX) course. This exam tests a candidate’s knowledge and skills required to install, operate, and troubleshoot a small to medium size enterprise branch network. The topics include all the areas covered under ICND 1 and ICND2 Exams.
QUESTION 7
What are two reasons a network administrator would use CDP? (Choose two.)
A. to obtain VLAN information from directly connected switches
B. to determine the status of network services on a remote device
C. to determine the status of the routing protocols between directly connected routers
D. to verify the type of cable interconnecting two devices
E. to verify Layer 2 connectivity between two devices when Layer 3 fails “Everything is under control” -www.pass4sure.com 5
F. to obtain the IP address of a connected device in order to telnet to the device
Correct Answer: EF
QUESTION 8
Refer to the exhibit. Both switches are using a default configuration. Which two destination addresses will host 4 use to send data to host 1? (Choose two.)
“Everything is under control” – www.pass4sure.com 6
A. the IP address of host 1
B. the IP address of host 4
C. the MAC address of host 1
D. the MAC address of host 4
E. the MAC address of the Fa0/0 interface of the R1 router
F. the MAC address of the Fa0/1 interface of the R1 router
Correct Answer: AF
QUESTION 9
Exhibit:
“Everything is under control” – www.pass4sure.com 7
Refer to the exhibit. The router has been configured with these commands:
What are the two results of this configuration? (Choose two.)
A. The default route should have a next hop address of 64.100.0.3.
B. Hosts on the LAN that is connected to FastEthernet 0/1 are using public IP addressing.
C. The address of the subnet segment with the WWW server will support seven more servers.
D. The addressing scheme allows users on the Internet to access the WWW server.
E. Hosts on the LAN that is connected to FastEthernet 0/1 will not be able to access the Internet “Everything is under control” – www.pass4sure.com 8 without address translation.
Correct Answer: DE
QUESTION 10
Your Company has installed IP phones. Both the phones and the office computers connect to the same device. The phone traffic and the office computer data traffic must be on different networks to ensure maximum throughput for the phone data. Which network device can be best connected to the phones and computers, and which technology will be performed on this device? (Choose two.)
A. hub
B. router
C. switch
D. stp
E. subinterfaces
F. VLAN
Correct Answer: CF
The VVJHV contains more than 400 practice questions for the Cisco 642-176 exams, including simulation-based questions. Also contains hands-on exercises and a customized copy of the Cisco 642-176 exams network simulation software.