Category: CCNP
Flydumps Cisco 642-901 exam questions and answers in PDF are prepared by our expert, Moreover, they are based on the recommended syllabus covering all the Cisco 642-901 exam objectives.You will find them to be very helpful and precise in the subject matter since all the Cisco 642-901 exam content is regularly updated and has been checked for accuracy by our team of SAP expert professionals.
QUESTION 110
Refer to the exhibit. Routers R1 and R2 are IPv6 BGP peers that have been configured to support a neighbor relationship over an IPv4 internetwork. Which three neighbor IP addresses are valid choices to use in the highlighted section of the exhibit? (Choose three.)
A. ::0A43:0002
B. 0A43:0002::
C. ::10.67.0.2
D. 10.67.0.2::
E. 0:0:0:0:0:0:10.67.0.2
F. 10.67.0.2:0:0:0:0:0:0
Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:
QUESTION 111
Refer to the exhibit. BGP has been configured on the routers in the network.
However, the IBGP peers in autonomous system 65200 have not converged. In addition, this console
message was generated on router R2:
*Mar 1 03:09:07.729: %TCP-6-BADAUTH No MD5 digest from 10.10.23.2(179) to 10.10.23.3(11002)
On the basis of the information that is provided, what is the cause of the problem?
A. BGP authentication can be used on eBGP peers only.
B. The password that is used for BGP authentication on both BGP peers in autonomous system 65200 must be the same.
C. BGP authentication can be used on iBGP peers when the connection is configured between the loopback interfaces.
D. OSPF must be configured with the same MD5 authentication.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 112
Refer to the exhibit diagram and configuration. RTB is summarizing its networks from AS 64100 with the aggregate-address command. However, the show ip route command on RTA reveals the RTB individual networks as well as its summary route. Which option would ensure that only the summary route would appear in the routing table of RTA?
A. Delete the four network statements and leave only the aggregate-address statement in the BGP configuration.
B. Add the keyword summary-only to the aggregate-address command.
C. Add a static route with a prefix of 192.168.24.0 255.255.252.0 pointing to the null0 interface.
D. Create a route map permitting only the summary address.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 113
Router RTA is configured as follows:
RTA (config)#router rip RTA(config-router)#network 10.0.0.0 RTA(config-router)#distribute-list 44 in interface BRI0 RTA(config-router)#exit RTA(config)#access-list 44 deny 172.16.1.0 0.0.0.255 RTA(config)#access-list 44 permit any
What are the effects of this RIP configuration on router RTA? (Choose two.)
A. no routing updates will be sent from router RTA on interface BRI0 to router RTX
B. router RTA will not advertise the 10.0.0.0 network to router RTX
C. the route to network 172.16.1.0 will not be entered into the routing table on router RTA
D. user traffic from the 172.16.1.0 network is denied by access-list 44
E. the routing table on router RTA will be updated with the route to router RTW
Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 114
During the redistribution process configured on RTA, some of the EIGRP routes, such as 10.1.1.0/24 and 10.2.2.0/24, are not being redistributed into the OSPF routing domain.
Which two items could be a solution to this problem? (Choose two.)
A. Change the metric-type to 2 in the redistribute command.
B. Configure the redistribute command under router eigrp 1 instead.
C. Change the EIGRP AS number from 100 to 1 in the redistribute command.
D. Add the subnets option to the redistribute command.
E. Change the metric to an EIGRP compatible metric value (bandwidth, delay, reliability, load, MTUs) in the redistribute command.
Correct Answer: CD Section: (none) Explanation
Explanation/Reference:
QUESTION 115
Which IS-IS router is equivalent to an ABR in OSPF?
A. Level 0
B. Level 1
C. Level 2
D. Level 3
E. Level 1-2
F. Level 2-3
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 116
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 receive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task?
A. R1(config)# router eigrp 1 R1(config-router)# passive-interface serial 0
B. R2(config)# router eigrp 1 R2(config-router)# passive-interface serial 0
C. R1(config)# access-list 20 deny any R1(config)# router eigrp 1 R1(config-router)# distribute-list 20 out serial 0
D. R2(config)# access-list 20 deny any R2(config)# router eigrp 1 R2(config-router)# distribute-list 20 out serial 0
E. R1(config)# access-list 20 permit any R1(config)# router eigrp 1 R1(config-router)# distribute-list 20 in serial 0
F. R2(config)# access-list 20 permit any R2(config)# router eigrp 1 R2(config-router)# distribute-list 20 in serial 0
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 117
Hotspot
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 118
Refer to the exhibit. Given the exhibited router output, which command sequence can be added to R1 to generate a default route into the OSPF domain?
A. default-router
B. ip default-network
C. default-information originate always
D. ip default-gateway
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 119
Refer to the exhibit. During the process of configuring a virtual link to connect area 2 with the backbone area, the network administrator received this console message on R3:
*Mar 1 00:25:01.084: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual link but not found from 20.20.20.1, Serial 0
How should the virtual link be configured on the OSPF routers to establish full connectivity between the areas?
A. R1(config-router)# area 1 virtual-link 30.30.30.3 R3(config-router)# area 1 virtual-link 20.20.20.1
B. R1(config-router)# area 1 virtual-link 20.20.20.2 R3(config-router)# area 1 virtual-link 30.30.30.2
C. R1(config-router)# area 0 virtual-link 1.1.1.1 R3(config-router)# area 2 virtual-link 3.3.3.3
D. R1(config-router)# area 1 virtual-link 3.3.3.3 R3(config-router)# area 1 virtual-link 1.1.1.1
E. R1(config-router)# area 1 virtual-link 2.2.2.2 R3(config-router)# area 1 virtual-link 2.2.2.2
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 120
LAB
A. Portland# conf t Portland(config)# router ospf 1 Portland(config-router)# network 192.168.5.4 0.0.0.3 area 1 Portland(config-router)# area 1 stub Portland(config-router)# end Portland# copy run start Indianapolis# conf t Indianapolis(config)# router ospf 1 Indianapolis(config-router)# network 192.168.5.4 0.0.0.3 area 1 Indianapolis(config-router)# area 1 stub no-summary Indianapolis(config-router)# end Indianapolis# copy run start
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 121
The command bgp always-compare-med is added to a router configuration.
What will this command accomplish?
A. forces the router to compare metrics of routes from different autonomous systems
B. forces the router to compare the local preference of routes from different autonomous systems
C. forces the router to compare the weight of routes from different autonomous systems
D. forces the router to compare the communities of routes from different autonomous systems
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 122
An administrator is redistributing OSPF into RIP. RIP is routing the 128.103.36.0/24 network. OSPF is routing the 128.103.35.32/28 network. Users in the RIP domain cannot reach devices in the OSPF domain. Which two tasks must be done to enable RIP to advertise the routes learned from OSPF into the RIP domain? (Choose two.)
A. Add a static route that points to the RIP domain address space with a /24 network mask and a next hop of 128.103.36.2.
B. Add a static route that points to the OSPF domain address space with a /24 network mask with a next hop of null0.
C. Tune the OSPF default metrics to allow seamless redistribution into RIP.
D. Redistribute configured static routes into RIP.
E. Use a route map statement inserted into a distribute list to control routing updates.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference: QUESTION 123
Which two provide intra-area routing services? (Choose two.)
A. L1 IS
B. L1 ES
C. L2 IS
D. L2 ES
E. L1/L2 IS
Correct Answer: AE Section: (none) Explanation
Explanation/Reference:
QUESTION 124
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the function of rendezvous point (RP) for the multicast network?
A. router R1
B. router R2
C. both routers R1 and R2
D. none of the routers since they are not configured with static RP
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 125
Refer to the exhibit. Which two statements are true about the partial configuration that is shown? (Choose two.)
A. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address 10.0.0.6.
B. The first DHCP client to connect to the FastEthernet 0/1 interface will receive the IP address 10.10.0.1.
C. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address 10.0.0.1
D. Hosts connected to the FastEthernet0/1 interface will not receive DHCP replies from the router.
E. DHCP requests received on the FastEthernet 0/1 interface will be forwarded to 10.0.0.2.
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 126
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 receive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task?
A. R1(config)# router eigrp 1 R1(config-router)# passive-interface serial 0
B. R2(config)# router eigrp 1 R2(config-router)# passive-interface serial 0
C. R1(config)# access-list 20 deny any R1(config)# router eigrp 1 R1(config-router)# distribute-list 20 out serial 0
D. R2(config)# access-list 20 deny any R2(config)# router eigrp 1 R2(config-router)# distribute-list 20 out serial 0
E. R1(config)# access-list 20 permit any R1(config)# router eigrp 1 R1(config-router)# distribute-list 20 in serial 0
F. R2(config)# access-list 20 permit any R2(config)# router eigrp 1 R2(config-router)# distribute-list 20 in serial 0
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 127
Hotspot
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 128
Refer to the exhibit. EIGRP is enabled on all routers on the network. What additional configuration is required for the routers connected over the Frame Relay multipoint interfaces to compensate for a low-speed NBMA connection?
A. Configure the EIGRP hello interval on all Frame Relay interfaces to 5 seconds.
B. Configure the EIGRP hello interval on all Frame Relay interfaces to 60 seconds.
C. Configure the EIGRP hold time on all Frame Relay interfaces to 15 seconds.
D. Configure the EIGRP hold time on all Frame Relay interfaces to 180 seconds.
E. Configure the bandwidth on all EIGRP Frame Relay interfaces to the committed information rate (CIR).
F. Configure the bandwidth on all EIGRP Frame Relay interfaces to the lowest CIR multiplied by the number of PVCs for the multipoint connection.
Correct Answer: F Section: (none) Explanation
Explanation/Reference:
QUESTION 129
Which show command will display the two values used in the calculation of the EIGRP metric?
A. show protocol
B. show ip eigrp interface
C. show interface
D. show ip eigrp neighbor
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 130
Which three restrictions apply to OSPF stub areas? (Choose three.)
A. No virtual links are allowed.
B. The area cannot be a backbone area.
C. Redistribution is not allowed unless the packet is changed to a type 7 packet.
D. The area has no more than 10 routers.
E. No autonomous system border routers are allowed.
F. Interarea routes are suppressed.
Correct Answer: ABE Section: (none) Explanation
Explanation/Reference:
QUESTION 131
Refer to the exhibit. IP multicast configuration changes have been made on several routers. However, the IP multicast table displayed in the exhibit still does not reflect the changes.
What should be done to display the new routing table information?
A. Issue the no ip mroute-cache privileged EXEC command.
B. Issue the clear ip igmp group privileged EXEC command.
C. Issue the clear ip mroute privileged EXEC command.
D. Issue the clear ip route * privileged EXEC command.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 132
Identify three characteristics of EIGRP feasible successors? (Choose three.)
A. A feasible successor is selected by comparing the advertised distance of a non-successor route to the feasible distance of the best route.
B. If the advertised distance of the non-successor route is less than the feasible distance of best route, then that route is identified as a feasible successor.
C. If the successor becomes unavailable, then the feasible successor can be used immediately without recalculating for a lost route.
D. The feasible successor can be found in the routing table.
E. Traffic will be load balanced between feasible successors with the same advertised distance.
Correct Answer: ABC Section: (none) Explanation
Explanation/Reference: QUESTION 133
What are three kinds of OSPF areas? (Choose three.)
A. stub
B. active
C. remote
D. backbone
E. ordinary or standard
Correct Answer: ADE Section: (none) Explanation
Explanation/Reference:
QUESTION 134
Based on the show ip bgp summary output, which two statements are true? (Choose two.)
A. The BGP session to the 10.1.1.1 neighbor is established.
B. The BGP session to the 10.2.2.2 neighbor is established.
C. The BGP session to the 10.3.3.3 neighbor is established.
D. The router is attempting to establish a BGP peering session with the 10.1.1.1 neighbor.
E. The BGP session to the 10.3.3.3 neighbor is established, but the router has not received any BGP routing updates from the 10.3.3.3 neighbor.
F. The router is attempting to establish a BGP peering session with the 10.2.2.2 neighbor.
Correct Answer: AF Section: (none) Explanation
Explanation/Reference:
Preparing Cisco 642-901 exam is not difficult now.You can prepare from Cisco 642-901 Certification or Cisco 642-901 dumps.Here we have mentioned some sample questions.You can use our Cisco 642-901 study material notes for test preparation. Latest Cisco 642-901 study material available.
You can prepare for Cisco 642-901 with little effort because Flydumps is now at your service to act as a guide in Flydumps you pass Cisco 642-901 exam. Now get that necessary competitive edge that comes with preparing with the help of Flydumps.
QUESTION 101
Which three statements are correct about the differences in IS-IS and OSPF? (Choose three.)
A. IS-IS LSP contains TLV fields and OSPF LSU contains the LSAs.
B. New additions to the protocol are easily implemented in OSPF but not with IS-IS.
C. For greater fine tuning there are more IS-IS timers.
D. OSPF has more area types than does IS-IS.
E. IS-IS is more CPU-intensive than is OSPF.
Correct Answer: ACD Section: Multiple Choice Questions Explanation
Explanation/Reference: QUESTION 102
What is the purpose of the eigrp stub configuration command?
A. to increase scalability by limiting the EIGRP query range
B. to reduce the size of the routing table by blocking the D EX (External EIGRP) routes into the EIGRP stub router
C. to reduce the convergence time by enabling the EIGRP stub router to propagate the EIGRP queries from the EIGRP hub router
D. to reduce the convergence time by enabling the EIGRP stub router to also perform query requests to the EIGRP hub router
Correct Answer: A Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 103
Which configuration commands will enable RTA to advertise all local interfaces over OSPF?
A. RTA(config)# router ospf 1RTA(config-router)# default-information originate
B. RTA(config)# router ospf 1RTA(config-router)# network 255.255.255.255 255.255.255.255
C. RTA(config)# router ospf 1RTA(config-router)# network 0.0.0.0
D. RTA(config)# router ospf 1RTA(config-router)# network 0.0.0.0 0.0.0.0
E. RTA(config)# router ospf 1RTA(config-router)# redistribute static
F. RTA(config)# router ospf 1RTA(config-router)# redistribute connected
Correct Answer: F Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 104
Which command lists the system IDs of all known IS-IS routers?
A. show clns neighbors
B. show isis database
C. show isis topology
D. show clns neighbors detail
E. show is-is neighbors detail
Correct Answer: C Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 105
Refer to the exhibit. Which two statements are true? (Choose two.)
A. The eigrp stub command prevents queries from being sent from R2 to R1.
B. The eigrp stub command will automatically enable summarization of routes on R2.
C. The eigrp stub command prevents all routes except a default route from being advertised to R1.
D. Router R1 will advertise connected and summary routes only.
E. Router R1 will advertise connected and static routes. The sending of summary routes will not be permitted.
F. Router R1 is configured as a receive-only neighbor and will not send any connected, static, or summary routes.
Correct Answer: AD Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 106
A network administrator would like to configure an EIGRP router as a stub router that advertises directly connected and summary routes only. What command must the administrator issue to accomplish this?
A. eigrp stub
B. eigrp stub connected
C. eigrp stub summary
D. eigrp stub connected static
E. eigrp stub receive-only
Correct Answer: A Section: Multiple Choice Questions Explanation Explanation/Reference:
QUESTION 107
Refer to the exhibit diagram and configuration. RTB is summarizing its networks from AS 64100 with the aggregate-address command. However, the show ip route command on RTA reveals the RTB individual networks as well as its summary route. Which option would ensure that only the summary route would appear in the routing table of RTA?
A. Delete the four network statements and leave only the aggregate-address statement in the BGP configuration.
B. Add the keyword summary-only to the aggregate-address command.
C. Add a static route with a prefix of 192.168.24.0 255.255.252.0 pointing to the null0 interface.
D. Create a route map permitting only the summary address.
Correct Answer: B Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 108
How is the designated querier elected in IGMPv2?
A. The first router to appear on a subnet is designated.
B. The host that responds first to the election query is designated.
C. The router with the lowest IP address on a subnet is designated.
D. The host with the lowest MAC address on a segment is designated.
Correct Answer: C Section: Multiple Choice Questions Explanation
Explanation/Reference: QUESTION 109
Which type of IGMP message is sent when a network client wants to join a multicast group?
A. host membership query
B. host membership report
C. host membership status
D. host membership notification
Correct Answer: B Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 110
When an IPv6 enabled host boots, it sends a router solicitation (RS) message. An IPv6 router responds with a router advertisement (RA). Which two items are contained in the RA? (Choose two.)
A. IPv6 address for the host
B. lifetime of the prefix
C. prefixes for the link
D. keepalive timers
E. request for the local host IP address
F. any route advertisements it has received
Correct Answer: BC Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 111
Which statement is true concerning 6to4 tunneling?
A. IPv4 traffic is encapsulated with an IPv6 header.
B. The edge routers can use any locally configured IPv6 address.
C. Hosts and routers inside a 6to4 site will need a special code.
D. An edge router must use IPv6 address of 2002::/16 in its prefix.
Correct Answer: D Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 112
Observe the exhibit. If the command variance 3 were added to RTE, which path or paths would be chosen to route traffic to network X?
A. E-B-A
B. E-B-A and E-C-A
C. E-C-A and E-D-A
D. E-B-A, E-C-A and E-D-A
Correct Answer: B Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 113
Refer to the exhibit. What happens when the router stops receiving advertisements for the 10.1.2.0/24 network?
A. The summary route will be removed from the table.
B. The summary route will remain in the table.
C. The more specific routes will be advertised from the table.
D. 10.1.2.0/24 will still be advertised but packets destined for it will be dropped when they reach this router.
Correct Answer: B Section: Multiple Choice Questions
Explanation Explanation/Reference:
QUESTION 114
Which statement is true about EBGP?
A. An internal routing protocol can be used to reach an EBGP neighbor.
B. The next hop does not change when BGP updates are exchanged between EBGP neighbors.
C. A static route can be used to form an adjacency between neighbors.
D. EBGP requires a full mesh.
Correct Answer: C Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 115
Refer to the exhibit. What is the effect of the distribute-list command in the R1 configuration?
A. R1 will filter only the 172.24.1.0/24 route from the R2 RIP updates.
B. R1 will permit only the 10.0.0.0/24 route in the R2 RIP updates.
C. R1 will filter the 10.1.0.0/24 and the 172.24.1.0/24 routes from the R2 RIP updates.
D. R1 will not filter any routes because there is no exact prefix match.
Correct Answer: C Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 116
Based on the information in the exhibit, which statement is true?
A. RTC will be able to access the 10.0.0.0 network.
B. RTC will not have the 10.0.0.0 network in its routing table.
C. RTC will not have the 192.168.10.0 network in its routing table.
D. RTB will not have the 10.0.0.0 network in its routing table.
E. RTB and RTC will not have the 10.0.0.0 network in their routing tables.
Correct Answer: B Section: Multiple Choice Questions Explanation
Explanation/Reference:
Well-regarded for its level of detail, assessment features, and challenging review questions and hands-on exercises, Cisco 642-901 helps you master the concepts and techniques that will enable you to succeed on the Cisco 642-901 exam the first time.
100% valid Cisco 642-901 Flydumps with more new added questions.By training the Cisco 642-901 questions, you will save a lot time in preparing the exam.Visit www.Flydumps.com to get the 100% pass Cisco 642-901 ensure!
QUESTION 137
Study the exhibit carefully. Configure BGP on all routers, turn off synchronization , and none of the default attributes have been changed except the local preference attribute on P4S4. Which path will be preferred by P4S2 to reach the network 100.100.100.0/24?
A. P4S2, P4S1 because it has the shortest AS-path
B. P4S2, P4S3, P4S4, P4S5 because it has a higher local preference
C. P4S2, P4S1 because it has a lower local preference
D. P4S2, P4S3, P4S4, P4S5 because it has a lower admin distance
Correct Answer: B Section: (none) Explanation QUESTION 138
Based on the configuration provided in the exhibit, how would the BGP updates that come from router P4S1 be replicated inside autonomous system 65200?
A. All BGP updates that are received on router P4S2 will not be sent to routers P4S3 and P4S4.
B. All BGP updates that are received on router P4S2 will be sent directly to router P4S5.
C. All BGP updates that are received on router P4S2 will be sent to routers P4S3 and P4S4. Routers P4S3 and P4S4 will then forward those BGP updates to router P4S5.
D. None of the BGP updates that are received on router P4S2 will ever be received by router P4S5.
Correct Answer: D Section: (none) Explanation
QUESTION 139
There are two routes in BGP to a destination. Assume that both paths were originated locally and have the same weight, what will be the next determining factor in choosing the best path?
A. lowest origin code
B. highest local preference
C. lowest MED
D. lowest neighbor IP address
Correct Answer: B Section: (none) Explanation
QUESTION 140
For the following commands, which one displays the IBGP and EBGP neighbors that are configured?
A. show ip bgp peers
B. show ip bgp
C. show ip bgp paths
D. show ip bgp summary
Correct Answer: D Section: (none) Explanation
QUESTION 141
Which two reasons are of the appearance of 0.0.0.0 as the next hop for a network in the show ip bgp command output? (Choose two.)
A. The network was originated via a network or aggregate command.
B. The network was learned via IBGP.
C. The network was originated via redistribution of an interior gateway protocol into BGP.
D. The network was defined by a static route.
Correct Answer: AC Section: (none) Explanation
QUESTION 142
Which one of the following statements accurately describes EBGP?
A. EBGP requires a full mesh.
B. An internal routing protocol can be used to reach an EBGP neighbor.
C. A static route can be used to form an adjacency between neighbors.
D. The next hop does not change when BGP updates are exchanged between EBGP neighbors.
Correct Answer: C Section: (none) Explanation
QUESTION 143
Judging from the show ip bgp summary output, which two descriptions are correct? (Choose two.)
A. The BGP session to the 10.1.1.1 neighbor is established.
B. The BGP session to the 10.3.3.3 neighbor is established.
C. The BGP session to the 10.2.2.2 neighbor is established.
D. The router is attempting to establish a BGP peering session with the 10.2.2.2 neighbor.
Correct Answer: AD Section: (none) Explanation
QUESTION 144
The command bgp always-compare-med is added to a router configuration. What will be the objective of this command?
A. forces the router to compare metrics of routes from different autonomous systems
B. forces the router to compare the communities of routes from different autonomous systems
C. forces the router to compare the local preference of routes from different autonomous systems
D. forces the router to compare the weight of routes from different autonomous systems
Correct Answer: A Section: (none) Explanation
Cisco 642-901 tests containing questions that cover all sides of tested subjects that help our members to be prepared and keep high level of professionalism.The main purpose of Cisco 642-901 exam is to provide high quality test that can secure and verify knowledge,give overview of question types and complexity that can be represented on real exam certification
Most accurate Cisco 642-892 practice test for you to free download.csci-scrc is also an authenticated IT certifications site that offer all the new questions and answers timely.Visit the site Flydumps.com to get free Cisco 642-892 VCE test engine and PDF.
QUESTION 85
Refer to the exhibit. What two statements are true about the IS-IS configuration? (Choose two.)
PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
A. The router is in area 49.0001.0002.
B. The router has a system ID of 0003.0004.
C. The router acts as a Level 1-2 router.
D. The network service access point selector (NSEL) byte has a value of 0. E. CLNS routing is enabled for the router.
Correct Answer: CD Section: (none) Explanation
Explanation/Reference: QUESTION 86
Refer to the exhibit. Which two statements about the IS-IS configurations of router R1 and router R2 are correct? (Choose two.)
PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
A. The IS-IS Level 2 metric that is assigned on the serial interface of router R2 is over three times the default value.
B. Router R1 sends only Level 1 hellos out the interface that is connected to R2.
C. Router R2 sends only Level 2 hellos out the interface that is connected to R1.
D. Router R1 is configured as a Level 1-2 router.
E. Router R2 has the same metric value assigned for Level 1 and Level 2 on the serial interface.
F. The network entity titles (NETs) that are configured on L1 and L2 are incompatible.
Correct Answer: AB Section: (none) Explanation
Explanation/Reference:
QUESTION 87
Refer to the exhibit. On the basis of the output, what two conclusions can be reached? (Choose two.)
PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
A. Three physical interfaces are taking part in integrated IS-IS.
B. Address summarization is configured.
C. There are two neighboring routers sending IS-IS routing information.
D. The default administrative distance has been changed.
E. IS-IS is not redistributing any other routing protocols.
F. IS-IS is not enabled.
Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 88
Which three options are supported as address allocation mechanisms for DHCP on Cisco routers? (Choose three.)
A. The IP address can be automatically assigned to a host.
B. The IP address can be assigned as a random hash value of the burned-in-address of the lowest-numbered LAN interface on the router.
C. The network administrator can assign a specific IP address to a specific host MAC address.
D. The IP address can be assigned from configured pools in a reverse lexicographical order.
E. The IP address can be assigned to a host for a limited time or until the host explicitly releases the address. PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
F. The IP address can be assigned to a host until the host usurps the assigned value using its own dynamic override mechanism.
Correct Answer: ACE Section: (none) Explanation
Explanation/Reference: QUESTION 89
Refer to the exhibit. What two conclusions can be made based on the DHCP configuration? (Choose two.)
A. The second DNS server configured will never be queried.
B. The first IP address assigned by DHCP is 172.16.0.1.
C. The IP address of the default router is used for DHCP relay.
D. The DHCP clients learn the excluded address ranges that area configured.
E. The configured domain name is propagated to the DHCP clients.
Correct Answer: BE Section: (none) Explanation
Explanation/Reference:
QUESTION 90
Refer to the exhibit. Which statement is true about the configuration?
PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
A. Hosts will receive IP settings from pool 1 until the addresses run out, and then hosts will receive the settings from pool 2.
B. Hosts belonging to DHCP pool 1 and pool 2 will retain their IP settings for 30 hours before they must renew.
C. Hosts in the 10.10.20.0/24 subnet will use 10.10.20.50 as its DNS server.
D. DHCP pool 0 needs to have the ip dhcp excluded-address command to exclude the default router and DNS servers.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 91
Refer to the exhibit. Which configuration is reflected in the output that is displayed in the exhibit?
A. neighbor 192.168.28.1 route-map cisco in ! access-list 66 permit 10.0.0.0 0.0.0.255 ! route-map cisco permit 10 match ip address 66 set local-preference 90 PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
B. neighbor 192.168.28.1 route-map cisco out ! access-list 66 permit 10.0.0.0 0.0.0.255 ! route-map cisco permit 10 match ip address 66 set metric 90
C. neighbor 192.168.28.1 route-map cisco out ! access-list 66 permit 10.30.0.0 0.0.255.255 ! route-map cisco permit 10 match ip address 66 set metric 90
D. neighbor 192.168.28.1 route-map cisco in ! PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892 access-list 66 permit 10.30.0.0 0.0.255.255 ! route-map cisco permit 10 match ip address 66 set local-preference 90
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 92
Refer to the exhibit. Router RT-1 chooses one path to network 198.133.219.0/24. Indicate the reason Router RT-1 chooses this “best” path.
A. In making its decision about the best path, RT-1 gives precedence to the origin code.
B. In making its decision about the best path, RT-1 gives precedence to the BGP MED values.
C. IP address 128.107.2.2 is lower than 128.107.255.2.
D. In making its decision about the best path, RT-1 prefers the IGP metrics.
E. RT-1 prefers internal BGP routes.
F. IP address 128.107.254.2 is lower than 128.107.255.2.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 93
What technique should be used on BGP edge routers to prevent a multi-homed autonomous system from becoming a transit system?
A. Advertise with a high MED value all networks that are discovered via external BGP.
B. Remove the AS-Path information on all routes in the BGP table prior to advertising externally.
C. Only advertise networks externally if they have been discovered via internal BGP.
D. Use an outgoing distribution list to filter all networks not originating from inside the autonomous system.
E. Set the no-export community attribute on all networks that are advertised externally.
F. Set the origin code to incomplete for all networks that are discovered via external BGP.
Correct Answer: D Section: (none) Explanation
Explanation/Reference: QUESTION 94
Refer to the exhibit. Which statement is true about the router configuration that is shown? PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
A. Additional DHCP options will be imported from another DHCP server.
B. The DHCP server pools need to be bound to an interface to operate.
C. This configuration will provide IP configuration information to two different subnets.
D. Additional DCHP option information needs to be imported from another DHCP server.
E. If the router hands out all the addresses in pool 1, then it will supply addresses from pool 2.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 95
Refer to the exhibit. Which statement is true about the router with ID 10.64.0.1?
A. It is the BDR for the local segment.
B. It is the DR for the local segment.
C. It is not running OSPF.
D. It has an OSPF priority of 1 on the attached interface.
E. It has a loopback that is configured.
F. It is not the DR or BDR for the local segment.
Correct Answer: F Section: (none) Explanation
Explanation/Reference:
QUESTION 96
Which statement is true about Protocol Independent Multicast Dense Mode (PIM DM) multicast routing?
A. PIM DM supports shared distribution trees.
B. If a port is pruned, the administrator must re-enable the port to support multicast traffic.
C. The (S,G) state exists in every router, regardless of the presence of an RPF interface.
D. Flooding of traffic only occurs in the beginning stages of routing. Afterwards, all necessary ports are pruned and multicast traffic is not sent across those interfaces.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 97
The show ip route command generated routes flagged as O N2 and O N1. Which option best describes how these routes were created?
PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
A. Summarization was performed on an ASBR connected to a totally stubby area.
B. Static routes were redistributed into an ASBR.
C. Redistribution was performed into a totally stubby area.
D. Redistribution was performed into an NSSA area.
E. Summarization was performed on an ASBR connected to a NSSA area.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 98
How is the configuration of a totally stubby area different from that of a stub area?
A. The totally stubby area requires the no-summary command on the ABR.
B. The totally stubby area requires the totally stubby command on the ABR.
C. The no-summary command should be included on all routers within the totally stubby area.
D. The totally stubby command should be included on all routers within the totally stubby area.
E. The totally stubby area requires the no-summary command on the ASBR.
Correct Answer: A Section: (none) Explanation
Explanation/Reference: QUESTION 99
Refer to the exhibit. Which one statement is true?
A. Traffic from the 172.16.0.0/16 network will be blocked by the ACL.
B. The 10.0.0.0/8 network will not be advertised by Router B because the network statement for the 10.0.0.0/8 network is missing from Router B.
C. The 10.0.0.0/8 network will not be in the routing table on Router B.
D. Users on the 10.0.0.0/8 network can successfully ping users on the 192.168.5.0/24 network, but users on the 192.168.5.0/24 cannot successfully ping users on the 10.0.0.0/8 network.
E. Router B will not advertise the 10.0.0.0/8 network because it is blocked by the ACL.
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 100
Refer to the exhibit. RTR-38 has two possible paths to reach the indicated networks but only chooses next hop 172.20.72.1. Which two options would cause RTR-38 to choose next hop 172.20.73.1 for network
192.168.101.0 but still use next hop 172.20.72.1 for the remaining networks? (Choose two)
PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
A. On RTR-38 apply a route map to neighbor 172.20.73.1 incoming that changes the local-preference to 200 for network 192.168.101.0.
B. On RTR-38 apply a route map to neighbor 172.20.73.1 incoming that changes the local-preference to 200 for all networks accept 192.168.101.0.
C. On RTR-38 apply the command neighbor 172.20.73.1 weight 200.
D. On RTR-38 apply the command neighbor 172.20.72.1 weight 200.
E. On BGP neighbor router 172.20.73.1 apply a route map that advertises a MED of 200 for network
192.168.101.0 to RTR-38.
F. On BGP neighbor router 172.20.72.1 apply a route map that advertises a MED of 200 for network
192.168.101.0 to RTR-38.
Correct Answer: AF Section: (none) Explanation
Explanation/Reference:
QUESTION 101
During BGP configuration on a router that has peered with other BGP speakers, the BGP command aggregate-address 172.32.0.0 255.255.252.0 is issued. However, the peers do not receive this aggregate network in BGP advertisements. Also, the router does not have this aggregate network in its BGP table. Which option indicates a possible reason this command did not cause the router to advertise the aggregate network to its peers?
A. Interface NULL 0 is likely shutdown.
B. The BGP command no synchronization is missing.
C. The BGP command no auto-summary is missing.
D. Subnets of 172.32.0.0/22 do not exist in the BGP table.
E. The IGP running on this router does not have network 172.32.0.0/22 installed.
F. The next hop IP address must be a loopback address.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 102
What are the two effects of the IP multicast global configuration command ip pim send-rp-announce loopback0 scope 31 group-list 5 issued on multicast router RTA? (Choose two.)
A. RTA will drop all RP announcements it receives if the TTL field is greater than 31.
B. RTA will forward RP announcements provided they are within the scope of 31.
C. RTA will originate RP announcements with TTL set to 31.
D. RTA will forward RP announcements from any neighbor router with a source IP address that matches access-list 5.
E. RTA will originate RP announcements for multicast groups that match access-list 5.
Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 103
Refer to the exhibit. Based on the output from the show command on RT1 which statement is true?
PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
A. OSPFv3 uses global IPv6 addresses to establish neighbor adjacencies.
B. RT1 has a subnet mask of 64 bits.
C. RT1 has FastEthernet0/0 set as a DR for network type broadcast.
D. OSPFv3 uses Link-local addresses to establish neighbor adjacencies.
E. RT1 does not have a global IPv6 address set on FastEthernet0/0.
F. OSPFv3 uses IPv4 addresses to establish neighbor adjacencies.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 104
Refer to the exhibit. In the show ipv6 route output, what would the metric be for a summary route that summarizes all three OSPFv3 routes displayed?
A. 20
B. 40
C. 100
D. 120
E. 140
F. 160
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
QUESTION 105
Refer to the exhibit. Which statement is correct regarding the partial configuration shown?
A. The router’s fa0/0 interface will be assigned the reserved address of 20.0.0.2.
B. The router will import its DHCP options from a configuration file on a TFTP server.
C. The router’s fa0/0 interface will be assigned any address from the 20.0.0.0/8 network except 20.0.0.2.
D. The router will add the DHCP option parameters it learns from another server into its DHCP server database.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 106
Refer to the exhibit. It is desired to set up a BGP neighbor relationship between routers R1 and R4. BGP packets between them could travel through R2 or R3. What is the simplest configuration that will allow for failover?
A. Configure BGP neighbor relationships between all interfaces on R1 and R4.
B. Install a direct connection between R1 and R4.
C. Configure loopback interfaces on R1 and R4 to provide the update source address for BGP packets.
D. Configure only one neighbor relationship between R1’s 192.168.1.2 interface and R4’s 172.16.10.2 interface.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
QUESTION 107
Refer to the exhibit. Routing updates for the 192.168.1.0 network are being received from all three neighbors. Which statement is correct regarding the result of the configuration shown?
A. The router will prefer the next hop of 172.16.1.1 for packets destined for the 192.168.1.0 network.
B. The router will prefer the next hop of 172.26.1.1 for packets destined for the 192.168.1.0 network.
C. The router will advertise the 192.168.1.0 network only to 172.30.1.1.
D. The router will advertise the 192.168.1.0 network only to 172.26.1.1.
E. The router will prefer the next hop of 172.26.1.1 for packets except those destined for the 192.168.1.0 network.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 108
Refer to the exhibit. The neighbor 10.1.1.1 weight 200 BGP configuration command has been configured on router A. What will be the result of this configuration?
A. Router A will prefer the path through router B for network 172.20.0.0. PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
B. Router A will prefer the path through router C for network 172.20.0.0.
C. Packets from router D will prefer the path through router B for networks advertised by router A.
D. Packets from router D will prefer the path through router C for networks advertised by router A.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 109
Which spanning-tree command would cause a PortFast-enabled interface to lose its PortFast-operational status and disable BPDU filtering if it receives BPDUs?
A. spanning-tree guard root
B. spanning-tree bpduguard enable
C. spanning-tree portfast bpduguard default
D. spanning-tree bpdufilter enable
E. spanning-tree portfast bpdufilter default
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 110
Which spanning-tree command would essentially disable spanning tree on an interface and make that interface susceptible to spanning-tree loops?
A. spanning-tree portfast bpdufilter default
B. spanning-tree bpdufilter enable
C. spanning-tree portfast bpduguard default
D. spanning-tree bpduguard enable
E. spanning-tree guard root
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 111
Which statement correctly describes the results of the Ethernet switch global configuration command spanning-tree loopguard default?
A. When any port receives a BPDU, it is put it in the error-disabled state.
B. An interface is moved directly to the spanning-tree forwarding state without waiting for the standard forward-time delay.
C. Prevents interfaces that are in a PortFast-operational state from sending or receiving BPDUs.
D. Detects indirect link failures and starts the spanning-tree reconfiguration sooner.
E. Prevents alternate or root ports from becoming designated ports because of a failure that leads to a unidirectional link.
F. Provides fast convergence after a direct link failure where a root port transitions to the forwarding state immediately without going through the listening and learning states.
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 112
Which optional feature of an Ethernet switch disables a port on a point-to-point link if the port does not receive traffic while Layer 1 status is up?
A. BackboneFast
B. UplinkFast
C. Loop Guard
D. UDLD aggressive mode
E. Fast Link Pulse bursts
F. Link Control Word
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 113
Which three statements are true about routed ports on a multilayer switch? (Choose three)
A. A routed port can support VLAN subinterfaces.
B. A routed port will take an IP address assignment.
C. A routed port can be configured with routing protocols.
D. A routed port is a virtual interface on the multilayer switch. PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
E. A routed port is only associated with one VLAN.
F. A routed port is a physical interface on the multilayer switch.
Correct Answer: BCF Section: (none) Explanation
Explanation/Reference:
QUESTION 114
Which three statements are true about CEF? (Choose three.)
A. The FIB table is derived from the IP routing table.
B. The adjacency table is derived from the ARP table.
C. CEF IP destination prefixes are stored in the TCAM table, from the least specific to the most specific entry.
D. When the CEF TCAM table is full, packets are dropped.
E. When the adjacency table is full, a CEF TCAM table entry points to the Layer 3 engine to redirect the adjacency.
F. The FIB lookup is based on the Layer 3 destination address prefix (shortest match).
Correct Answer: ABE Section: (none) Explanation
Explanation/Reference:
QUESTION 115
Refer to the exhibit. Why are users from VLAN 100 unable to ping users on VLAN 200?
PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
A. Encapsulation on the switch is wrong.
B. Trunking needs to be enabled on Fa0/1.
C. The native VLAN is wrong.
D. VLAN 1 needs the no shutdown command.
E. IP routing needs to be enabled on the switch.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 116
Refer to the exhibit. What problem is preventing users on VLAN 100 from pinging addresses on VLAN 200?
PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
A. No default route on DLS1.
B. Encapsulation mismatch between switches.
C. Native VLAN mismatch.
D. Subinterfaces should be created on Fa0/7 and Fa0/8 on DLS1.
E. Trunking needs to be enabled.
F. The ip routing command is missing on DLS1.
Correct Answer: F Section: (none)
Explanation
Explanation/Reference:
QUESTION 117
Which three characteristics are true about voice traffic in the campus network? (Choose three.)
A. bursty
B. greedy
C. drop sensitive
D. delay sensitive
E. UDP priority
F. TCP retransmits
Correct Answer: CDE Section: (none) Explanation
Explanation/Reference:
QUESTION 118
Which three characteristics are true about voice traffic in the campus network? (Choose three.)
A. TCP retransmits
B. benign
C. greedy
D. drop sensitive
E. smooth
F. delay insensitive
Correct Answer: BDE Section: (none) Explanation
Explanation/Reference:
QUESTION 119
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf PassGuide.com-Make You Succeed To Pass IT Exams PassGuide 642-892
neighbor output, what prevents R1 from establishing a full adjacency with R2?
A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multiaccess networks.
B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.
C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.
D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.
E. The Hello parameters on routers R1 and R2 do not match.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 120
Which two statements are true about voice VLANs? (Choose two.)
A. Voice VLANs allow IP phones to be moved around without worrying about subnets.
B. Voice VLANs allow voice and data packets to be logically combined.
C. Implementing voice VLANs causes network administrators to change their existing IP topology.
D. Using voice VLANs makes it easier for network administrators to identify and troubleshoot network problems.
E. Voice VLANs are available on all Cisco switches.
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 121
Which two statements are true about trust boundaries? (Choose two.)
A. Classifying and marking traffic should be done as close to the traffic source as possible.
B. Classifying and marking traffic should be done at the distribution layer.
C. Traffic is classified and marked as it travels through the network.
D. If untrusted traffic enters a switch, it can be marked with a new QoS value appropriate for the policy in place.
E. The trust boundary moves depending on the type of traffic entering the network.
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
Try Cisco 642-892 exam free demo before you decide to buy it in Flydumps.After you buy Flydumps Cisco 642-892 exam dumps, you will get free update for ONE YEAR!
Flydumps just published the newest Cisco 642-813 dumps with all the new updated exam questions and answers.Flydumps provide the latest version of Cisco 642-813 and VCE files with up-to-date questions and answers to ensure your exam 100% pass, on our website you will get the free new newest Cisco 642-813 version VCE Player along with your VCE dumps.
QUESTION 80 Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 81
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 82
A.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 83
Correct Answer: BF Section: (none) Explanation
Explanation/Reference:
QUESTION 84 Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 85
B.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 86
Correct Answer: D Section: (none) Explanation
Explanation/Reference: QUESTION 87
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 88
A.
B.
C.
D.
E.
F.
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 89 Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 90
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 91 Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 92
A.
B.
D.
Correct Answer: AE Section: (none) Explanation
Explanation/Reference:
QUESTION 93 Correct Answer: ABC Section: (none) Explanation
Explanation/Reference:
QUESTION 94
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
QUESTION 95
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 96
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 97
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 98
B.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 99
C.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 100
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 101
A. active
B. speak
C. learn
D. listen
E. init
F. standby
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
Whenever Cisco candidates take a tour of sample questions of Cisco 642-813 exam they find their training to be matchless to great extent.Passing the Cisco 642-813 on your own can be a difficult task,but with Cisco 642-813 preparation products,many candidates who appeared online passed Cisco 642-813 easily.