Author: newcertskey
Cisco 640-822 Certification exams Q and A provided by Flydumps will make you feel like you are taking an actual exam at a Prometric or VUE center. Furthermore,we are constantly updating our Cisco 640-822 practice material.Our candidates walk into the testing Room as confident as a Certification Administrator.So you can pass the eaxm beyond any doubt.
QUESTION 50
Part of the configuration of router TT 1 is shown below: Exhibit
What is the effect of the configuration shown above on router TT 1 ?
A. It configures SSH globally for all logins.
B. It tells the router or switch to try to establish an SSH connection first and if that fails to use Telnet.
C. It configures the virtual terminal lines with the password 030752180500.
D. It configures a Cisco network device to use the SSH protocol on incoming communications via the virtual terminal ports.
E. It allows seven failed login aTT empts before the VTY lines are temporarily shutdown.
F. None of the above.
Correct Answer: D
QUESTION 51
You need to make changes to a new Troytec router. By which prompt is the global configuration mode on this router identified?
A. Router(config-line)#
B. Router(config-router)#
C. Router#
D. Router(config)#
E. Router>
F. Router(config-if)#
G. None of the above
Correct Answer: D
QUESTION 52
You need to configure a new Cisco router for remote access on the Troytec network. How many simultaneous telnet sessions does this Cisco router support by default?
A. 4
B. 2
C. 5
D. 1
E. 6
F. 0
Correct Answer: C
QUESTION 53
The interface status of a Troytec router is shown below:
Exhibit The result of the show interfaces serial 0/0 command is displayed in the exhibit. What command should be executed to make this interface operational?
A. Troytec C(config-if)# enable
B. Troytec C(config-if)# no keepalive
C. Troytec C(config-if)# encapsulation pop
D. Troytec C(config-if)# no shutdown
E. Troytec C(config-if)# clock rate 56000
F. Troytec C(config-if)# line protocol up
Correct Answer: D
QUESTION 54
Which of the following commands displays the configurable parameters and statistics of all interfaces on a router?
A. show interfaces
B. show processes
C. show running-config
D. show versions
E. show startup-config
Correct Answer: A
QUESTION 55
The following was seen on a Troytec router in Huntsville:
Exhibit Refer to the router output shown in the graphic. What can be assumed about the network attached to this router interface?
A. The network hosts are attached to a hub.
B. The interface is being used at near maximum capacity.
C. There should never be any collisions in this network.
D. The network has an excessive number of errors.
E. The network is using an unusual Ethernet encapsulation.
F. None of the above
Correct Answer: C
QUESTION 56
Refer to the output of the three Troytec router commands shown in the exhibit. A new technician has been told to add a new LAN to the company router. Why has the technician received the error message that is shown following the last command?
Exhibit A. The command was entered from the wrong prompt.
B. The router does not support LAN interfaces that use Ethernet.
C. The interface was already configured.
D. The IOS software loaded on the router is outdated.
E. The interface type does not exist on this router platform.
F. None of the above
Correct Answer: E
QUESTION 57
: In the Troytec router below, serial0/0 does not respond to a ping request from a host on the FastEthernet0/0 LAN.
Exhibit
Based on the information above, how can this problem be corrected?
A. Correct the IP address for interface Serial 0/0.
B. Change the encapsulation type on interface Serial 0/0.
C. Correct the IP address for interface FastEthernet 0/0.
D. Enable auto configuration on the Serial 0/0 interface.
E. Enable the Serial 0/0 interface.
F. None of the above
Correct Answer: E
QUESTION 58
An administrator issues the show ip interface s0/0 command and the output displays that interface Serial0/0 is up, line protocol is up What does “line protocol is up” specifically indicate about the interface?
A. The cable is attached properly.
B. CDP has discovered the connected device.
C. Keepalives are being received on the interface.
D. A carrier detect signal has been received from the connected device.
E. IP is correctly configured on the interface.
Correct Answer: C
QUESTION 59
You need to configure the interfaces on a new Troytec router, but first you need to enter the global configuration mode. Which command is used on router Troytec 3 to reach this mode?
A. Troytec 3# router
B. Troytec 3# setup
C. Troytec 3# interface
D. Troytec 3> enable
E. Troytec 3# configure terminal
Correct Answer: E
QUESTION 60
In the network shown below, The Troytec technician is testing connection problems. What is the problem indicated by the output from HostA?
Exhibit A. The gateway address of HostA is incorrect or not configured.
B. An access list is applied to an interface of Troytec 3.
C. The routing on Troytec 2 is not functioning properly.
D. The Fa0/24 interface of Switch1 is down.
E. None of the above
Correct Answer: A
QUESTION 61
Regarding the extended ping command; which of the statements below are true? (Select all valid answer choices)
A. The extended ping command is supported from user EXEC mode.
B. The extended ping command is available from privileged EXEC mode.
C. With the extended ping command you can specify the TCP and UDP port to be pinged.
D. With the extended ping command you can specify the timeout value.
E. With the extended ping command you can specify the datagram size.
Correct Answer: BDE
QUESTION 62
When you use the ping command to send ICMP messages across a network, what’s the most common request/reply pair you’ll see? (Select one answer choice)
A. Echo request and Echo reply
B. ICMP hold and ICMP send
C. ICMP request and ICMP reply
D. Echo off and Echo on
E. None of the above
Correct Answer: A QUESTION 63
Part of the Troytec network is shown below: Exhibit
Ping exhibit: Exhibit
Tracert exhibit: Exhibit
You work as a network technician at Troytec .com. You are testing connection problems in the network and your PC (host Troytec A) has provided the output shown above. What is the problem indicated by this output?
A. The routing on Router Troytec 2 is not functioning properly.
B. The Fa0/24 interface of Switch Troytec 4 is down.
C. An access list is applied to an interface of Router Troytec 3.
D. The gateway address of Host Troytec A is incorrect or not configured.
E. None of the above
Correct Answer: D
QUESTION 64
Network Topology Exhibit:
Troytec 1 configuration exhibit: Exhibit
Troytec 2 configuration exhibit: Exhibit
You need to ensure connectivity between two new Troytec offices. You apply the configurations in the exhibit into the two new routers Troytec 1 and Troytec 2. Otherwise, the routers are configured with their default configurations. A ping from Host Troytec A to Host Troytec B fails, but you are able to ping the S0/0 interface of Troytec 2 from Host Troytec A. The configurations of the hosts have been verified as correct. What could be the cause of the problem?
A. The interfaces on Troytec 2 are not configured properly.
B. The serial cable on Troytec 1 needs to be replaced.
C. The IP addressing scheme has overlapping subnetworks.
D. Router Troytec 1 has no route to the 192.168.1.128 network.
E. The ip subnet-zero command must be configured on both routers.
Correct Answer: D
QUESTION 65
You need to configure a default route on a Troytec router. Which command will configure a default route on a router?
A. TT 1 (config)# ip route 0.0.0.0 10.1.1.0 10.1.1.1
B. TT 1 (config)# ip default-route 10.1.1.0
C. TT 1 (config)# ip default-gateway 10.1.1.0
D. TT 1 (config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1
Correct Answer: D
QUESTION 66
Static routing needs to be configured on router TT 1. In which situation would the use of a static route be appropriate?
A. To configure a route to the first Layer 3 device on the network segment.
B. To configure a route from an ISP router into a corporate network.
C. To configure a route when the administrative distance of the current routing protocol is too low.
D. To reach a network is more than 15 hops away.
E. To provide access to the Internet for enterprise hosts.
F. None of the above
Correct Answer: B
QUESTION 67
The Troytec network is shown below:
Exhibit Based on this information, which of the following will configure a static route on Router A to network 180.18.30.0/24 with an administrative distance of 90?
A. Router(config)# ip route 90 180.18.20.1 255.255.255.0 182.18.20.2
B. Router(config)# ip route 180.18.20.1 255.255.255.0 182.18.30.0 90
C. Router(config)# ip route 180.18.30.1 255.255.255.0 182.18.20.1 90
D. Router(config)# ip route 90 180.18.30.0 255.255.255.0 182.18.20.2
E. Router(config)# ip route 180.18.30.0 255.255.255.0 182.18.20.2 90
Correct Answer: E
QUESTION 68
The network administrator of the Oregon router adds the following command to the router configuration: ip
route 192.168.12.0 255.255.255.0 172.16.12.1. What are the results of adding this command? (Choose
two.)
Exhibit:
Exhibit
A. Traffic for network 192.168.12.0 is forwarded to 172.16.12.1.
B. This route is automatically propagated throughout the entire network.
C. Traffic for all networks is forwarded to 172.16.12.1.
D. Traffic for network 172.16.12.0 is forwarded to the 192.168.12.0 network.
E. The command invokes a dynamic routing protocol for 192.168.12.0.
F. The command establishes a static route.
Correct Answer: AF
QUESTION 69
Which of the commands below can you use to configure a default route on router TT 1 ? (Select two answer choices)
A. TT 1 (config)# ip route 0.0.0.0 0.0.0.0 E0
B. TT 1 (config)# ip route 0.0.0.0 255.255.255.255 S0
C. TT 1 (config-interface)# ip route 255.255.255.255 0.0.0.0 192.168.1.21
D. TT 1 (config)# ip route 0.0.0.0 0.0.0.0 192.168.1.21
E. TT 1 (config)# ip route 0.0.0.0 192.168.1.21 255.255.255.255
F. TT 1 # ip default-network 0.0.0.0 192.168.1.21 255.255.255.255
Correct Answer: AD
QUESTION 70
Which of the following commands would you use to configure a default route to any destination NOT found in the routing table of router TT 1 ?
A. TT 1 (config)# ip default-route 0.0.0.0 255.255.255.255 s0
B. TT 1 (config)# ip route 0.0.0.0 255.255.255.255 s0
C. TT 1 (config)# ip default-route 0.0.0.0 0.0.0.0 s0
D. TT 1 (config)# ip route 0.0.0.0 0.0.0.0 s0
E. TT 1 (config)# ip route any any e0
F. None of the above
Correct Answer: D
QUESTION 71
The topology of the Troytec network is displayed below, along with the routing table of the Troytec 1 router:
Exhibit
172.17.22.0 172.31.5.0 Changes to the Troytec network were made, and now users on the Troytec 3 LAN are not able to connect to the Troytec 4 LAN. Based on the information above, what could be the reason for this?
A. The Fast Ethernet interface is disabled.
B. The neighbor relationship table is not updated.
C. A static route is configured incorrectly.
D. The routing table on Troytec 1 is not updated.
E. IP routing is not enabled.
Correct Answer: C
QUESTION 72
Some of the Troytec routers have been configured with default routes. What are some of the advantages of using default routes? (Choose two)
A. They establish routes that will never go down.
B. The keep routing tables small.
C. They require a great deal of CPU power.
D. The allow connectivity to remote networks that are not in the routing table.
E. They direct traffic from the Internet into corporate networks.
Correct Answer: BD
QUESTION 73
You have just configured a static default route on router TT 1 . What is the purpose of a default route?
A. It is a route to be used when the routing protocol fails.
B. It is a route configured by an ISP that sends traffic into a corporate network.
C. It is a route used when a packet is destined for a remote network that is not listed in the routing table.
D. It is a route manually configured for a specific remote network for which a routing protocol is not configured.
E. It is used to send traffic to a stub network. F. None of the above
Correct Answer: C
QUESTION 74
On router TT 1 the following configuration command was entered: ip route 0.0.0.0 0.0.0.0 192.168.1.2 What is the result of adding this command to this router when it is already configured for dynamic routing?
A. It configures the router to block routing updates from being sent to IP address 192.168.1.2.
B. It configures the router to send all packets to IP address 192.168.1.2 if the packets match no other entry in the routing table.
C. It configures the router to drop all packets for which the destination network is unknown.
D. It configures the router to send all packets to IP address 192.168.1.2.
E. It configures the router as a firewall, blocking all packets from IP address 192.168.1.2.
F. None of the above
Correct Answer: B
QUESTION 75
If NVRAM in a Troytec router lacks boot system commands, where does this router look for the Cisco IOS by default?
A. ROM
B. RAM
C. Flash
D. Bootstrap
E. Startup-.config
F. None of the above
Correct Answer: C
QUESTION 76
When you power up a Troytec router; in what memory is the start-up configuration normally stored in?
A. RAM
B. ROM
C. FLASH
D. NVRAM
E. None of the above
Correct Answer: D
QUESTION 77
You are the administrator of the Troytec network and you have forgoTT en the password to one of your routers. After completing the password recovery procedure the router returned to its normal operation. The config-register was set back to the initial default value. What is this value?
A. 0x2112
B. 0x2104
C. 0x2102
D. 0x2142
E. 0x2100
Correct Answer: C QUESTION 78
You issued the following command on router Troytec 3: Exhibit
When upgrading the IOS image, you receive the exhibited error message shown above. Based on the information given, what could be the cause of this error?
A. The TFTP server is unreachable from the router.
B. The new IOS image is too large for the router flash memory.
C. The IOS image on the TFTP server is corrupt.
D. The new IOS image is not correct for this router platform.
E. There is not enough disk space on the TFTP server for the IOS image.
F. None of the above
Correct Answer: A
QUESTION 79
The relevant system information regarding a Troytec router is shown in the following display:
Exhibit
Refer to the partial Command output shown. Which two statements are correct regarding the router hardware? (Choose Two)
A. Total RAM Size is 32 KB.
B. Total RAM Size is 16384 KB (16 MB)
C. Total RAM Size is 65536 KB (64 MB)
D. FLASH Size is 32 KB.
E. FLASH Size is 16384 KB (16 MB)
F. FLASH Size is 65536 KB (64 MB)
Correct Answer: CE
QUESTION 80
Which is the correct fallback sequence for loading the Cisco IOS?
A. ROM, Flash, NVRAM
B. ROM, TFTP server, Flash
C. Flash, TFTP server, ROM
D. Flash, NVRAM, RAM
Correct Answer: C
QUESTION 81
See the following exhibit below:
Exhibit
A router consistently loses its configuration each time it reboots. Given the output shown in the graphic, what is the cause of this problem?
A. The processor is overheating.
B. Configuration register is misconfigured.
C. There is no problem.
D. Cisco products are inferior compared to Nortel products. Migrate to Nortel instead.
E. None of the above
Correct Answer: B
QUESTION 82
A Cisco router has been configured, and the copy running-config startup-config command has been
issued. When the router is power cycled, the router prompts with:
“Would you like to enter the initial configuration dialog? [yes/no]” Why has this occurred?
A. There is an error in the router DRAM.
B. Te IOS image is corrupt.
C. The configuration register is set to 0x2142.
D. The TFTP server that contains the router configuration file is unreachable.
E. A boot system configuration command has placed the router into setup mode.
Correct Answer: C QUESTION 83
What is the purpose of using the copy flash tftp command on a router?
A. To copy an IOS image to the router
B. To create a backup copy of the IOS
C. To move the IOS image from a server to the router
D. To backup the router configuration to a server
Correct Answer: B QUESTION 84
Refer to the following exhibit: Exhibit
The Troytec network administrator configures a new router and enters the copy startup- config running-config command on the router. He powers down the router and sets it up at a remote location. When the router starts, it enters the system configuration dialog as shown. What is the cause of the problem?
A. The network administrator failed to save the configuration.
B. The configuration register is set to 0x2100.
C. The boot system flash command is missing from the configuration.
D. The configuration register is set to 0x2102.
E. The router is configured with the boot system startup command.
F. None of the above
Correct Answer: A
QUESTION 85
Before installing a new, upgraded version of the IOS, what should be checked on the router, and which command should be used to gather this information? (Choose two)
A. show running-config
B. show version
C. the version of the bootstrap software present on the router
D. the amount of available ROM
E. the amount of available flash and RAM memory
F. show processes
Correct Answer: BE
QUESTION 86
Drag and Drop You work as a network administrator at Troytec .com. Your boss, Mrs. Troytec , tells you to match the commands with the appropriate descriptions. One of the commands listed below will not be used.
Select and Place:
Correct Answer:
QUESTION 87
Which of the commands below would you enter if you wanted to see the configuration register of your router?
A. show boot
B. show flash
C. show register
D. show version
E. show config
F. None of the above
Correct Answer: D
QUESTION 88
After logging into a router, you type in “enable” and then enter the correct password when prompted. What is the current router prompt symbol at this point?
A. >
B. #
C. ?
D. *
E. All of the above
F. None of the above
Correct Answer: B
QUESTION 89
In the Cisco IOS, what is the definition of a global command?
A. A command that can be entered in any configuration mode.
B. A command that supports all protocols.
C. A command that is implemented in all IOS versions.
D. A command that is set once and affects the entire router.
E. A command that is available in every release of IOS.
Correct Answer: D
QUESTION 90
Which of the following commands will display the name of the IOS image file being used in a Troytec router?
A. Router# show IOS
B. Router# show version
C. Router# show image
D. Router# show protocols
E. Router# show flash
Correct Answer: BE
Get yourself composed for Microsoft actual exam and upgrade your skills with Flydumps Cisco 640-822 practice test products. Once you have practiced through our assessment material, familiarity on Cisco 640-822 exam domains get a significant boost. Flydumps practice tests enable you to raise your performance level and assure the guaranteed success for Cisco 640-822 exam.
Important Info: These new valid CheckPoint 156-915 exam questions were updated in recent days by CheckPoint 156-915 ,please visit our website to get the full version of new CheckPoint 156-915 exam dumps with free version of new VCE Player, you can pass the exam easily by training it!
QUESTION 87
Which feature in VPN-1 permits blocking specific IP addresses for a specified time period?
A. HTTP Methods
B. Local Interface Spoofing
C. Block Port Overflow
D. Suspicious Activity Monitoring
Correct Answer: D
QUESTION 88
Match the ClusterXL Modes with their configurations: Exhibit:
A. A2,B3,C1,D4
B. A2,B3,C4,D1
C. A3,B2,C4,D1
D. A3,B2,C1,D4
Correct Answer: D
QUESTION 89
By default Check Point High Availability components send updates about their state every:
A. 1 Second
B. 0.1 Second
C. 5 Seconds
D. 0.5 seconds
Correct Answer: B
QUESTION 90
Which operating system is not supported by SecureClient?
A. IPSO 3.9
B. MacOS X
C. Windows 2003 Professional
D. Windows XP SP2
Correct Answer: A
QUESTION 91
Which of the following is the most critical step in a SmartCenter Server NGX R65 backup strategy?
A. Move the *.tgz upgrade_export file to an offsite location via ftp
B. Perform a full system tape backup of both the SmartCenter and Security Gateway machines
C. Using the upgrade_import command, attempt to restore the SmartCenter server to a non-production system
D. Run the cpstop command prior to running the upgrade_export command
Correct Answer: C
QUESTION 92
What happens when you select File > Export from the SmartView Tracker Menu?
A. Logs in fw.log are exported to a file that can be opened by Microsoft Excel
B. Exported log entries are deleted from fw.log
C. Current logs are exported to a new *.log file
D. Exported log entries are still viewable in SmartView Tracker
Correct Answer: A QUESTION 93
Which of these components does NOT require a VPN-1 NGX R65 license?
A. SmartUpdate Upgrading/Patching
B. SmartCenter Server
C. Check Point Gateway
D. SmartConsole
Correct Answer: D QUESTION 94
How do you use SmartView Monitor to compile traffic statistics for your company’s Internet activity during production hours?
A. Use the “Traffic Counters” settings and SmartView Monitor to generate a graph showing the total HTTP traffic for the day
B. Configure Suspicious Activity Rule which triggers an alert when HTTP traffic passes through the Gateway
C. Select the “Tunnels” view and generating a report on the statistics
Correct Answer: A QUESTION 95
Which Check Point product is used to create and save changes to a Log Consolidation Policy?
A. Eventia Reporter Server
B. SmartDashboard Log Consolidator
C. SmartCenter Server
D. Eventia Reporter Client
Correct Answer: B QUESTION 96
When configuring site-to-site VPN High Availability (HA) with MEP, which of the following is correct?
A. MEP Gateways must be managed by the same SmartCenter Server
B. If one MEP Security Gateway fails, the connection is lost and the backup Gateway picks up the next connection
C. MEP Gateways cannot be geographically separated machines
D. The decision on which MEP Gateway to use is made on the MEP Gateway’s side of the tunnel
Correct Answer: B QUESTION 97
You have blocked an IP address via the Block intruder feature of Smartview Tracker. How can you see the addresses you have blocked?
A. In Smartview monitor, select Blocked Intruder option from the query tree view
B. Run fwm blocked_view
C. In Smartview monitor, select Suspicious activity rules from the tools menu and select the relevant security gateway from the list
D. In SmartView Tracker,Click the Active Tab, and the actively blocked connection display
Correct Answer: C
QUESTION 98
You are administering your company’s clientless VPN connections. How many Security Servers should you be running to support 750 active users?
A. 1
B. 7
C. 5
D. 3
Correct Answer: C
QUESTION 99
What is the most typical type of configuration for VPNs with several externally managed Gateways?
A. Star Community
B. Hybrid community
C. Mesh Community
D. Domain Community
Correct Answer: A
QUESTION 100
Which of the following is TRUE concerning unnumbered VPN Tunnel Interfaces (VTIs)?
A. VTIs are only supported on SecurePlatform
B. VTI specific additional local and remote IP addresses are not configured
C. VTIs cannot be assigned a proxy interface
D. Local IP addresses are not configured, remote IP addresses are configured
Correct Answer: B
QUESTION 101
When configuring VPN High Availability (HA) with MEP, which of the following is correct?
A. If one gateway fails, the synchronized connection fails over to another Gateway and the connection continues
B. The decision on which MEP Security Gateway to use is made on the remote gateway’s side (non-MEP side)
C. MEP VPN Gateways cannot be geographically separated machines
D. MEP Gateways must be managed by the same SmartCenter Server
Correct Answer: B
QUESTION 102
___________ is a proprietary check point protocol. It is the basis of the functionality of Check Point ClusterXL inter-module communication.
A. HA OPCODE
B. CKPP
C. RDP
D. CCP
Correct Answer: D QUESTION 103
Which of the following command is a CLI command for VPN-1 NGX R65?
A. fw shutdown
B. fwprint
C. fw tab -u
D. fw merge
Correct Answer: C QUESTION 104
Match each of the following commands to their correct function. Each command only has one function
listed:
Exhibit:
A. C1>F2;C2>F1;C3>F6;C4>F4
B. C1>F4;C2>F6;C3>F3;C4>F2
C. C1>F2;C2>F4;C3>F1;C4>F5
D. C1>F6;C2>F4;C3>F2;C4>F5
Correct Answer: D
QUESTION 105
Which security servers can perform authentication tasks, but CANNOT perform content security tasks?
A. HTTP
B. FTP
C. RLOGIN
D. SMTP
Correct Answer: C
QUESTION 106
You are running the License_upgrade tool on you SecurePlatform Gateway. Which of the following can you NOT do with the upgrade tool?
A. Perform the actual license-upgrade process
B. View the status of currently installed licenses
C. Simulate the license-upgrade process
D. View the licenses in the SmartUpdate License Repository
Correct Answer: D QUESTION 107
A marketing firm’s networking team is trying to troubleshoot user complaints regarding access to audio-streaming material from the Internet. The networking team asks you to check the object and rule configuration settings for the perimeter security gateway. Which SmartConsole application should you use to check these objects and rules?
A. SmartView Statuus
B. SmartView Monitor
C. SmartView Tracker
D. SmartDashboard
Correct Answer: A QUESTION 108
Which is the BEST configuration option to protect internal users from malicious java code, without stripping Java Scripts?
A. Use the URI resource to strip ActiveX tags
B. Use the URI resource to strip applet tags
C. Use CVP in the URI resource to block Java code
D. Use the URI resource to block Java Code
Correct Answer: D QUESTION 109
You organization has many VPN-1 Edge Gateways at various branch offices, to allow users to access company resources. For security reasons, your organization’s security policy requires all internet traffic initiated behind the VPN-1 Edge Gateways first be inspected by your headquarters VPN-1 Pro Security Gateway. How do you configure VPN routing in this star VPN community?
A. To the Internet and other targets only
B. To the center and other satellites, through the center
C. To the center or through the center to other satellites, then to the Internet and other VPN targets
D. To the center only
Correct Answer: C QUESTION 110
Users are not prompted for authentication when they access their web servers, even though you have created an HTTP rule via User Authentication. Why?
A. Another rule that accepts HTTP without authentication exists in the Rule Base
B. You have forgotten to place the User Authentication Rule before the Stealth Rule
C. Users must use the SecuRemote Client, to use the User Authentication Rule
D. You checked the “Cache password on desktop” option in Global Properties
Correct Answer: B QUESTION 111
Flydumps is now offering CheckPoint 156-915 dumps PDF and Test Engine with 100% passing guarantee. Buy CheckPoint 156-915 pdf and pass your exam easily. If you want real exam simulation then buy test engine and install on your pc for preparation. Download CheckPoint 156-915 CCIE Data Center questions answers study material and prepare for exam.
100% valid Checkpoint 156-816 brain dumps with more new added questions.By training the Checkpoint 156-816 questions, you will save a lot time in preparing the exam.Visit www.Flydumps.com to get the 100% pass ensure!
QUESTION 77
During MDS installation, you must configure at least one VSX Administrator. After creating the Administrator, you are prompted to perform which task?
A. Grant VSX-specific privileges to the Administrator
B. Assign the Administrator to manage a specific Virtual System
C. Add the Administrator to a group
D. Assign the Administrator to manage a specific interface on the VSX Gateway
E. Assign the Administrator to manage a specific CMA
Correct Answer: C
QUESTION 78
During the initial configuration of a VSX Gateway cluster, the VSX Administrator is prompted to specify each cluster member’s name, as shown below:Which of the following best describes this name?
A. IP address of the individual VSX Gateway in the cluster
B. Any name the VSX Administrator chooses to describe the cluster member
C. Customer for which this VSX Gateway cluster is configured
D. MAC address of the individual VSX Gateway in the cluster
E. Hostname of the individual VSX Gateway in the cluster
Correct Answer: B
QUESTION 79
The VSX Management Server uses which of the following channels to communicate with components of the VSX Gateway?
A. Provisioning and Network Configuration
B. Route Configuration
C. Gateway Inspection Verification
D. Status Verification
E. Policy Verification
Correct Answer: A
QUESTION 80
What is the maximum number of members that can be included in a VSX Gateway cluster?
A. 2
B. 10
C. 50
D. 8
E. 25
Correct Answer: D
QUESTION 81
If two VSX Gateways are deployed in a cluster with one interface defined with a Virtual Switch, how is each Virtual Switch instance defined?
A. Primary: Standby/Secondary: Active
B. Primary: Standby/Secondary: Standby
C. Primary: Active/Secondary: Standby
D. Primary: Active/Secondary: Active
Correct Answer: D
QUESTION 82
What is the term used to describe a port or interface that shares traffic from more than one VLAN?
A. Frame-Strata enabled
B. VLAN riding
C. Comprehensive layer-2 label support
D. VLAN trunking
E. Comprehensive VLAN Tag support
Correct Answer: D
QUESTION 83
The provisioning and network configuration channel does NOT:
A. Install a default Security Policy blocking all traffic.
B. Install Administrator defined Security Policies.
C. Create Virtual Systems and Virtual Routers on a Gateway.
D. Configure interface and routing information on the Gateway.
E. Create a SIC Certificate for new objects, and transfer the Certificate to an object on the VSX Gateway.
Correct Answer: B
QUESTION 84
In a VLAN Tag added to a frame header, the __________ is a 2 byte number that identifies a frame as tagged.
A. user_priority
B. VLAN Identifier
C. Tag Control Information
D. Tag Protocol Identifier
E. Canonical Format Indicator
Correct Answer: D
QUESTION 85
Which of the following VSX components maintain layer 3 connectivity?
A. Virtual System in Bridge mode
B. Internal Virtual Switch
C. External Virtual Switch
D. Virtual Router
E. VLAN interface
Correct Answer: D
QUESTION 86
When configuring a Virtual System interface leading to a Virtual Switch, the default Gateway must be: A. The IP address of the Virtual Switch.
B. The IP address of the Management Virtual System.
C. The IP address of a device outside the VSX Gateway.
D. Excluded. No default Gateway is used when passing traffic through a Virtual Switch.
E. Shared among all systems passing through the switch.
Correct Answer: C
QUESTION 87
Which interface of the Management Virtual System (MVS) can be compared to the external interface of a traditional Security Gateway?
A. Warp interface leading from the MVS to the External Virtual Router
B. None; the External Virtual Router acts as the external interface to all Virtual Systems configured on the VSX Gateway.
C. Dedicated management interface, typically eth0
D. Synchronization interface
E. Virtual interface leading from the MVS to the External Virtual Router
Correct Answer: A
QUESTION 88
When deploying a VSX Gateway managed by a SmartCenter Server, which of the following statements is TRUE?
A. VSX Administrators can configure different domains for each Virtual System.
B. Multiple Administrators can simultaneously connect to the same database, to manage multiple Customers.
C. All Customer objects, rules, and users are shared in a single database.
D. Each Virtual System has its own unique Certificate Authority.
E. VSX superuser Administrators can configure granular permissions for each Customer Administrator.
Correct Answer: C
QUESTION 89
A __________ is a virtual security device configured on a VSX Gateway, which operates as a complete routing and security domain, with firewall and VPN capabilities.
A. Virtual Switch
B. Context Identification Module
C. Virtual System Extension
D. Virtual System
E. External Virtual Router
Correct Answer: D
QUESTION 90
When configuring Virtual Systems with overlapping IP addressing, the Virtual Systems must:
A. Be included in a VPN.
B. Be on the same network.
C. Perform Network Address Translation.
D. Perform in Bridge mode.
E. Define VLAN Tags.
Correct Answer: C QUESTION 91
Consider the following scenario: Your network configuration requires that you configure a single interface on the VSX Gateway to lead to multiple networks. A different Virtual System must protect each network sending traffic through the VSX Gateway. You configured a dedicated management interface on the VSX Gateway, along with 1 External Virtual Router and 4 Virtual Systems, one for each Customer. Which of the following hardware devices must be used to connect the different networks to the single shared interface?
A. Frame cache-redirection enabled switch
B. Content-intelligent switch
C. Jumbo frame-enabled switch
D. Router
E. VLAN-capable switch
Correct Answer: E
QUESTION 92
When configuring the VSX Gateway, it is important to reboot after running which of the following commands for the first time?
A. config
B. cpconfig vsx
C. fwconfig
D. vsx sysconfig
E. sysconfig
Correct Answer: E
QUESTION 93
Bridged Virtual Systems in a cluster monitor which of the following protocols, to fail over a bridged system?
A. VTP
B. MPLS
C. BPDU
D. STP
E. OSPF
Correct Answer: C
QUESTION 94
You need to provide a security layer for an existing core network. You need an inspection module that operates at layer 2, is completely transparent, and does not impact the existing IP structure or different control protocols in use. Which of the following virtual devices will perform the kind of inspection you need?
A. External Virtual Router
B. Virtual Switch
C. Virtual System in Bridge mode
D. Virtual System
E. Internal Virtual Router
Correct Answer: C
QUESTION 95
Which of the following statements is true concerning the default Security Policy of the External Virtual Router?
A. The External Virtual Router performs exactly like an External Virtual Switch.
B. All traffic emanating from networks protected by the VSX Gateway is dropped. All other traffic is accepted.
C. All traffic passing through the External Virtual Router is allowed by default, without inspection by the External Virtual Router’s Security Policy.
D. All traffic bound for the management network is dropped.
E. Virtual Routers do not enforce a Security Policy.
Correct Answer: C
QUESTION 96
Which of the following commands should you run to stop a VSX Gateway cluster?
A. vsxhastop
B. vsx cpstop
C. cpstop
D. cphastop
E. vsxstop
Correct Answer: C
QUESTION 97
Which of the following elements is NOT maintained separately by each Virtual System on a VSX Gateway?
A. Configuration parameters
B. Management database
C. Logging parameters
D. Security Policies
E. State tables
Correct Answer: B
QUESTION 98
When configuring a Warp Link, what is the IP address that appears in the topology properties of the External Virtual Router?
A. 255.255.255.255
B. Either the IP address designated as the main IP for the Virtual System to which the link connects, or its Static Network Address Translation IP address
C. Always the IP address designated as the main IP, for the Virtual System to which the link connects
D. Same as the IP address of the External Virtual Router
E. 0.0.0.0
Correct Answer: E
QUESTION 99
If a VSX Gateway is protecting multiple customer networks behind only one shared interface, the VSX Administrator must either configure __________ for source-based routing, or deploy a VLAN solution.
A. An Internal Virtual Router
B. Non-VLAN Interface Trunking
C. VSX Gateway High Availability
D. VSX Gateway Load Sharing
E. Multiple External Virtual Routers
Correct Answer: A
QUESTION 100
Consider the following scenario: A hub connects four hosts to a VLAN-Tagged port on a switch. The hosts have IP addresses ranging from 10.0.0.1 to 10.0.0.4. The switch adds a VLAN Tag of 400 to all communication passing through it. Once communication from the second host on the hub passes through the switch port on the way to its destination on the external network, how does the traffic appear in SmartView Tracker? Assume that traffic enters the Gateway on interface eth3.
A. eth3.2
B. eth3.400.2
C. eth3.400
D. eth3.2.400
E. eth3.402
Correct Answer: C
QUESTION 101
When configuring a VLAN environment for your VSX Gateway, you must associate each VLAN with an interface and an IP address. Where is each VLAN setting configured?
A. System Interfaces tab of the VSX Gateway object
B. Add/Edit Interface screen, accessed from the Topology tab of the Virtual Router object
C. System Interfaces Allocation tab of the VSX Gateway object
D. Add/Edit Interface screen, accessed from the Topology tab of the Virtual System object
E. VLAN Configuration tab of the VSX Gateway object
Correct Answer: D
QUESTION 102
When deploying a VSX Gateway managed by a SmartCenter Server, how many Certificate Authorities will the deployment have?
A. One for each Virtual System and Virtual Router configured on the VSX Gateway
B. One, shared by all components
C. Two; one for the SmartCenter Server, and one shared by all Virtual Systems and Virtual Routers
D. One for each Virtual System configured on the VSX Gateway
E. Three; one for the SmartCenter Server, one shared by all Virtual Systems, and one shared by the Virtual Routers
Correct Answer: B
QUESTION 103
Which of the following MDS types allows you to create and manage a VSX Gateway?
A. MDS Manager station
B. MDS Container station
C. MDS VSX Integrator
D. MDS MLM
E. MDS SmartCenter for VSX
Correct Answer: B
QUESTION 104
Which of the following objects allows you to configure resource settings, to limit the number of concurrent connections?
A. Internal Virtual Router
B. Virtual Systems
C. Virtual Switch
D. External Virtual Router
E. VSX Gateway
Correct Answer: B
QUESTION 105
Where within the frame header is the VLAN Tag inserted?
A. Before Destination information
B. After Type/Length information
C. Before Source information
D. Before Type/Length information
E. Either before Type/Length information or after, depending on the Canonical Format Indicator setting
Correct Answer: D
QUESTION 106
Which two segments make up a VLAN Tag, following the standard IEEE format?
A. Tag Protocol Identifier and VLAN Identifier
B. Tag Protocol Identifier and Traffic Control Information
C. Canonical Format Indicator and Traffic Control Information
D. Traffic Control Information and VLAN Identifier
E. Canonical Format Indicator and Tag Protocol Identifier
Correct Answer: B
QUESTION 107
Which of the following VSX Gateway configurations is valid?
A. A shared NIC assigned to different Virtual Systems, with the same IP addresses on different VLANs
B. A shared NIC assigned to different Virtual Systems, with different IP addresses on the same VLAN
C. A shared NIC assigned to different Virtual Systems, with the same IP addresses on the same VLAN
D. Multiple NICs assigned the same IP addresses, for each Virtual System in the configuration, but with different VLAN Tags
E. Multiple NICs assigned to different Virtual Systems in Bridge Mode, performing Hide NAT
Correct Answer: A
QUESTION 108
A VSX cluster configuration is built from which three components?
A. Management Network, Internal Communications Network, Virtual IP Addresses
B. Synchronization Network, Internal Communications Network, Virtual IP Addresses
C. Management Network, Internal Virtual Network, Virtual IP Addresses
D. Synchronization Network, Internal Network, External Network
E. Synchronization Network, Virtual Network, External Network
Correct Answer: B
QUESTION 109
Which of the following is a type of VLAN membership?
A. Time-based
B. Application-based
C. Port-based
D. Session-based
E. Protocol-based
Correct Answer: E
QUESTION 110
A Warp Link is a virtual point-to-point connection between a:
A. Virtual Router and Virtual System.
B. Virtual Router and Virtual Switch.
C. Virtual System and the management interface.
D. Virtual Router and a physical interface.
E. Virtual System and another Virtual System.
Correct Answer: A
With the products Checkpoint 156-816 for training and preparation of testing you would not only significantly reduce your fees, but pass your exam. We obtain our products from Authorities experts from test center.We give you the best path to successful completion of your exam to the real and original exam questions and answers for Checkpoint 156-816.
New VCE and PDF– If you want to pass CheckPoint 156-706 exam successfully,do not miss to test Cisco latest CheckPoint 156-706 brain dumps.All CheckPoint 156-706 the new questions and answers were timely added, visit Flydumps.com to free download VCE player and PDF files.
QUESTION 90 If a helpdesk user is logged in to webRH and you decide to remove his account, when will the user be notified?
A. Immediately, since he will be thrown off the system when his account is removed
B. When his session times out and he tries to re-authenticate
C. When he reboots his machine
D. Never, it is not possible to remove accounts from webRH
Correct Answer: B
QUESTION 91 What are the names of the Pointsec processes and services that run on a workstation after Pointsec has been installed?
A. Pointsec.exe, psadmin.exe and decrypt.exe
B. Prot_srv.exe, p95tray.exe and pstartsr.exe
C. Pssogina.exe, pointsec.exe and p95tray.exe
D. Decrypt.exe, protect.exe and pssogina.exe, pagents.exe
Correct Answer: B
QUESTION 92
How many authorized users must log in to uninstall Pointsec for PC?
A. One
B. Two
C. Three
D. Four
Correct Answer: B
QUESTION 93
What does Removable Media Manager do?
A. Manages what media can be exported to Removable Media
B. Automatically formats and encrypts devices
C. Automatically scans and digitally signs devices
D. Creates a black / white list of what devices can be used on the network
Correct Answer: D
QUESTION 94
Which application can you run to configure webRH settings post installation?
A. webRHconfig.exe
B. addtoken.exe
C. admin.exe
D. none of the above
Correct Answer: A
Flydumps.com is the absolute way to pass your CheckPoint 156-706 exam within no time. An authentic and comprehensive CheckPoint 156-706 exam solution is available at Flydumps.com. With our exclusive online CheckPoint 156-706 braindump you will pass CheckPoint 156-706 exam easily.Flydumps.com guarantees 100% success rate.
Flydumps Cisco 642-901 exam questions and answers in PDF are prepared by our expert, Moreover, they are based on the recommended syllabus covering all the Cisco 642-901 exam objectives.You will find them to be very helpful and precise in the subject matter since all the Cisco 642-901 exam content is regularly updated and has been checked for accuracy by our team of SAP expert professionals.
QUESTION 110
Refer to the exhibit. Routers R1 and R2 are IPv6 BGP peers that have been configured to support a neighbor relationship over an IPv4 internetwork. Which three neighbor IP addresses are valid choices to use in the highlighted section of the exhibit? (Choose three.)
A. ::0A43:0002
B. 0A43:0002::
C. ::10.67.0.2
D. 10.67.0.2::
E. 0:0:0:0:0:0:10.67.0.2
F. 10.67.0.2:0:0:0:0:0:0
Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:
QUESTION 111
Refer to the exhibit. BGP has been configured on the routers in the network.
However, the IBGP peers in autonomous system 65200 have not converged. In addition, this console
message was generated on router R2:
*Mar 1 03:09:07.729: %TCP-6-BADAUTH No MD5 digest from 10.10.23.2(179) to 10.10.23.3(11002)
On the basis of the information that is provided, what is the cause of the problem?
A. BGP authentication can be used on eBGP peers only.
B. The password that is used for BGP authentication on both BGP peers in autonomous system 65200 must be the same.
C. BGP authentication can be used on iBGP peers when the connection is configured between the loopback interfaces.
D. OSPF must be configured with the same MD5 authentication.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 112
Refer to the exhibit diagram and configuration. RTB is summarizing its networks from AS 64100 with the aggregate-address command. However, the show ip route command on RTA reveals the RTB individual networks as well as its summary route. Which option would ensure that only the summary route would appear in the routing table of RTA?
A. Delete the four network statements and leave only the aggregate-address statement in the BGP configuration.
B. Add the keyword summary-only to the aggregate-address command.
C. Add a static route with a prefix of 192.168.24.0 255.255.252.0 pointing to the null0 interface.
D. Create a route map permitting only the summary address.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 113
Router RTA is configured as follows:
RTA (config)#router rip RTA(config-router)#network 10.0.0.0 RTA(config-router)#distribute-list 44 in interface BRI0 RTA(config-router)#exit RTA(config)#access-list 44 deny 172.16.1.0 0.0.0.255 RTA(config)#access-list 44 permit any
What are the effects of this RIP configuration on router RTA? (Choose two.)
A. no routing updates will be sent from router RTA on interface BRI0 to router RTX
B. router RTA will not advertise the 10.0.0.0 network to router RTX
C. the route to network 172.16.1.0 will not be entered into the routing table on router RTA
D. user traffic from the 172.16.1.0 network is denied by access-list 44
E. the routing table on router RTA will be updated with the route to router RTW
Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 114
During the redistribution process configured on RTA, some of the EIGRP routes, such as 10.1.1.0/24 and 10.2.2.0/24, are not being redistributed into the OSPF routing domain.
Which two items could be a solution to this problem? (Choose two.)
A. Change the metric-type to 2 in the redistribute command.
B. Configure the redistribute command under router eigrp 1 instead.
C. Change the EIGRP AS number from 100 to 1 in the redistribute command.
D. Add the subnets option to the redistribute command.
E. Change the metric to an EIGRP compatible metric value (bandwidth, delay, reliability, load, MTUs) in the redistribute command.
Correct Answer: CD Section: (none) Explanation
Explanation/Reference:
QUESTION 115
Which IS-IS router is equivalent to an ABR in OSPF?
A. Level 0
B. Level 1
C. Level 2
D. Level 3
E. Level 1-2
F. Level 2-3
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 116
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 receive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task?
A. R1(config)# router eigrp 1 R1(config-router)# passive-interface serial 0
B. R2(config)# router eigrp 1 R2(config-router)# passive-interface serial 0
C. R1(config)# access-list 20 deny any R1(config)# router eigrp 1 R1(config-router)# distribute-list 20 out serial 0
D. R2(config)# access-list 20 deny any R2(config)# router eigrp 1 R2(config-router)# distribute-list 20 out serial 0
E. R1(config)# access-list 20 permit any R1(config)# router eigrp 1 R1(config-router)# distribute-list 20 in serial 0
F. R2(config)# access-list 20 permit any R2(config)# router eigrp 1 R2(config-router)# distribute-list 20 in serial 0
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 117
Hotspot
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 118
Refer to the exhibit. Given the exhibited router output, which command sequence can be added to R1 to generate a default route into the OSPF domain?
A. default-router
B. ip default-network
C. default-information originate always
D. ip default-gateway
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 119
Refer to the exhibit. During the process of configuring a virtual link to connect area 2 with the backbone area, the network administrator received this console message on R3:
*Mar 1 00:25:01.084: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual link but not found from 20.20.20.1, Serial 0
How should the virtual link be configured on the OSPF routers to establish full connectivity between the areas?
A. R1(config-router)# area 1 virtual-link 30.30.30.3 R3(config-router)# area 1 virtual-link 20.20.20.1
B. R1(config-router)# area 1 virtual-link 20.20.20.2 R3(config-router)# area 1 virtual-link 30.30.30.2
C. R1(config-router)# area 0 virtual-link 1.1.1.1 R3(config-router)# area 2 virtual-link 3.3.3.3
D. R1(config-router)# area 1 virtual-link 3.3.3.3 R3(config-router)# area 1 virtual-link 1.1.1.1
E. R1(config-router)# area 1 virtual-link 2.2.2.2 R3(config-router)# area 1 virtual-link 2.2.2.2
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 120
LAB
A. Portland# conf t Portland(config)# router ospf 1 Portland(config-router)# network 192.168.5.4 0.0.0.3 area 1 Portland(config-router)# area 1 stub Portland(config-router)# end Portland# copy run start Indianapolis# conf t Indianapolis(config)# router ospf 1 Indianapolis(config-router)# network 192.168.5.4 0.0.0.3 area 1 Indianapolis(config-router)# area 1 stub no-summary Indianapolis(config-router)# end Indianapolis# copy run start
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 121
The command bgp always-compare-med is added to a router configuration.
What will this command accomplish?
A. forces the router to compare metrics of routes from different autonomous systems
B. forces the router to compare the local preference of routes from different autonomous systems
C. forces the router to compare the weight of routes from different autonomous systems
D. forces the router to compare the communities of routes from different autonomous systems
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 122
An administrator is redistributing OSPF into RIP. RIP is routing the 128.103.36.0/24 network. OSPF is routing the 128.103.35.32/28 network. Users in the RIP domain cannot reach devices in the OSPF domain. Which two tasks must be done to enable RIP to advertise the routes learned from OSPF into the RIP domain? (Choose two.)
A. Add a static route that points to the RIP domain address space with a /24 network mask and a next hop of 128.103.36.2.
B. Add a static route that points to the OSPF domain address space with a /24 network mask with a next hop of null0.
C. Tune the OSPF default metrics to allow seamless redistribution into RIP.
D. Redistribute configured static routes into RIP.
E. Use a route map statement inserted into a distribute list to control routing updates.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference: QUESTION 123
Which two provide intra-area routing services? (Choose two.)
A. L1 IS
B. L1 ES
C. L2 IS
D. L2 ES
E. L1/L2 IS
Correct Answer: AE Section: (none) Explanation
Explanation/Reference:
QUESTION 124
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the function of rendezvous point (RP) for the multicast network?
A. router R1
B. router R2
C. both routers R1 and R2
D. none of the routers since they are not configured with static RP
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 125
Refer to the exhibit. Which two statements are true about the partial configuration that is shown? (Choose two.)
A. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address 10.0.0.6.
B. The first DHCP client to connect to the FastEthernet 0/1 interface will receive the IP address 10.10.0.1.
C. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address 10.0.0.1
D. Hosts connected to the FastEthernet0/1 interface will not receive DHCP replies from the router.
E. DHCP requests received on the FastEthernet 0/1 interface will be forwarded to 10.0.0.2.
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 126
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 receive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task?
A. R1(config)# router eigrp 1 R1(config-router)# passive-interface serial 0
B. R2(config)# router eigrp 1 R2(config-router)# passive-interface serial 0
C. R1(config)# access-list 20 deny any R1(config)# router eigrp 1 R1(config-router)# distribute-list 20 out serial 0
D. R2(config)# access-list 20 deny any R2(config)# router eigrp 1 R2(config-router)# distribute-list 20 out serial 0
E. R1(config)# access-list 20 permit any R1(config)# router eigrp 1 R1(config-router)# distribute-list 20 in serial 0
F. R2(config)# access-list 20 permit any R2(config)# router eigrp 1 R2(config-router)# distribute-list 20 in serial 0
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 127
Hotspot
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 128
Refer to the exhibit. EIGRP is enabled on all routers on the network. What additional configuration is required for the routers connected over the Frame Relay multipoint interfaces to compensate for a low-speed NBMA connection?
A. Configure the EIGRP hello interval on all Frame Relay interfaces to 5 seconds.
B. Configure the EIGRP hello interval on all Frame Relay interfaces to 60 seconds.
C. Configure the EIGRP hold time on all Frame Relay interfaces to 15 seconds.
D. Configure the EIGRP hold time on all Frame Relay interfaces to 180 seconds.
E. Configure the bandwidth on all EIGRP Frame Relay interfaces to the committed information rate (CIR).
F. Configure the bandwidth on all EIGRP Frame Relay interfaces to the lowest CIR multiplied by the number of PVCs for the multipoint connection.
Correct Answer: F Section: (none) Explanation
Explanation/Reference:
QUESTION 129
Which show command will display the two values used in the calculation of the EIGRP metric?
A. show protocol
B. show ip eigrp interface
C. show interface
D. show ip eigrp neighbor
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 130
Which three restrictions apply to OSPF stub areas? (Choose three.)
A. No virtual links are allowed.
B. The area cannot be a backbone area.
C. Redistribution is not allowed unless the packet is changed to a type 7 packet.
D. The area has no more than 10 routers.
E. No autonomous system border routers are allowed.
F. Interarea routes are suppressed.
Correct Answer: ABE Section: (none) Explanation
Explanation/Reference:
QUESTION 131
Refer to the exhibit. IP multicast configuration changes have been made on several routers. However, the IP multicast table displayed in the exhibit still does not reflect the changes.
What should be done to display the new routing table information?
A. Issue the no ip mroute-cache privileged EXEC command.
B. Issue the clear ip igmp group privileged EXEC command.
C. Issue the clear ip mroute privileged EXEC command.
D. Issue the clear ip route * privileged EXEC command.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 132
Identify three characteristics of EIGRP feasible successors? (Choose three.)
A. A feasible successor is selected by comparing the advertised distance of a non-successor route to the feasible distance of the best route.
B. If the advertised distance of the non-successor route is less than the feasible distance of best route, then that route is identified as a feasible successor.
C. If the successor becomes unavailable, then the feasible successor can be used immediately without recalculating for a lost route.
D. The feasible successor can be found in the routing table.
E. Traffic will be load balanced between feasible successors with the same advertised distance.
Correct Answer: ABC Section: (none) Explanation
Explanation/Reference: QUESTION 133
What are three kinds of OSPF areas? (Choose three.)
A. stub
B. active
C. remote
D. backbone
E. ordinary or standard
Correct Answer: ADE Section: (none) Explanation
Explanation/Reference:
QUESTION 134
Based on the show ip bgp summary output, which two statements are true? (Choose two.)
A. The BGP session to the 10.1.1.1 neighbor is established.
B. The BGP session to the 10.2.2.2 neighbor is established.
C. The BGP session to the 10.3.3.3 neighbor is established.
D. The router is attempting to establish a BGP peering session with the 10.1.1.1 neighbor.
E. The BGP session to the 10.3.3.3 neighbor is established, but the router has not received any BGP routing updates from the 10.3.3.3 neighbor.
F. The router is attempting to establish a BGP peering session with the 10.2.2.2 neighbor.
Correct Answer: AF Section: (none) Explanation
Explanation/Reference:
Preparing Cisco 642-901 exam is not difficult now.You can prepare from Cisco 642-901 Certification or Cisco 642-901 dumps.Here we have mentioned some sample questions.You can use our Cisco 642-901 study material notes for test preparation. Latest Cisco 642-901 study material available.