Welcome to download the newest Flydumps 300-207 VCE dumps: http://www.flydumps.com/300-207.html
A site with a decent screen would likely have a very good understanding environment. Rather than the consumer screen it’s essential to as well check for selections much like the query high quality as well as the way in which handy it really is intended for getting ready for the fundamental analyze! FLYDUMPS Cisco 642-812 exam sample questions is a reliable source of information for the candidates who want to take the Cisco 640-878 exam. The Cisco 642-812 is the composite exam associated with the Cisco 642-812 certification. The Cisco 642-812 certification strengthens the employment prospects and opens up myriads of opportunities for them. FLYDUMPS Cisco 642-812 exam sample questions provides the useful information about the exam.
QUESTION 127
Which statement is true about the Forward Information Base (FIB) table?
A. The FIB is derived from the IP routing table and is optimized for maximum lookup throughput.
B. The FIB table is derived from the Address Resolution Protocol table, and it contains Layer 2 rewrite (MAC) information for the next hop.
C. The FIB lookup is based on the Layer 2 destination MAC address.
D. When the FIB table is full, a wildcard entry redirects traffic to the Layer 3 engine.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 128
Refer to the exhibit. Both host stations are part of the same subnet but are in different VLANs. On the
basis of the information presented in the exhibit, which statement is true about an attempt to ping from host
to host?
A. A trunk port will need to be configured on the link between Sw_A and Sw_B for the ping command to be successful.
B. The two different hosts will need to be in the same VLAN in order for the ping command to be successful.
C. A Layer 3 device is needed for the ping command to be successful. TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
D. The ping command will be successful without any further configuration changes.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 129
Which switch command enables a trunking protocol that appends a four byte CRC to the packet?
A. Switch(config-if)#switchport trunk encapsulation dot1q
B. Switch(config-if)#switchport trunk encapsulation itef
C. Switch(config-if)#switchport trunk encapsulation fddi
D. Switch(config-if)#switchport trunk encapsulation isl
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 130
Which statement describes Dynamic Trunking Protocol (DTP) mode ‘desirable’?
A. The interface is put into permanent trunking mode and negotiates to convert the link into a trunk link.
B. The interface actively attempts to convert the link to a trunk link.
C. The interface is put into permanent trunking mode but prevented from generating DTP frames.
D. The interface is put into a passive mode, waiting to convert the link to a trunk link.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 131
Which three statements are correct with regard to the IEEE 802.1Q standard? (Choose three.)
A. the packet is encapsulated with a 26 byte header and a 4 byte FCS
B. the IEEE 802.1Q frame format adds a 4 byte field to a Ethernet frame
C. the IEEE 802.1Q frame retains the original MAC destination address
D. the IEEE 802.1Q frame uses multicast destination of 0x01-00-0c-00-00
E. protocol uses point-to-point connectivity
F. protocol uses point-to-multipoint connectivity
Correct Answer: BCE Section: (none) Explanation
Explanation/Reference:
QUESTION 132
In a customer’s network, VLAN Trunking Protocol (VTP) is running with a domain named main1.
VLANs 1,2,3,4,5,10,20 are active on the network. Suddenly the whole network goes down. No traffic is
being passed on VLANs 2,3,4,5,10,20, however traffic passes on VLAN 1 and indicates all switches are
operational. Right before the network problem occurred, a switch named TEST1 was added to the
network.
TestInside Help You Pass Any IT Exam
http://www.TestInside.com Testinside What three configuration issues on TEST1 could be causing the network outage? (Choose three.)
A. TEST1 is configured as a VTP server with a different domain name.
B. TEST1 is not configured to participate in VTP.
C. TEST1 is configured as a VTP server with the domain name main1.
D. TEST1 has a lower VTP configuration revision than the current VTP revision.
E. TEST1 has a higher VTP configuration revision than the current VTP revision.
F. TEST1 is configured with only VLAN1.
Correct Answer: CEF Section: (none) Explanation
Explanation/Reference:
QUESTION 133
Which DTP switchport mode parameter sets the switch port to actively send and respond to DTP negotiation frames?
A. access
B. trunk
C. no negotiate
D. dynamic desirable
E. dynamic auto
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 134
Which method of Layer 3 switching uses a forwarding information base (FIB)?
A. route caching
B. flow-based switching
C. demand-based switching
D. topology-based switching
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 135
Which protocol specified by RFC 2281 provides network redundancy for IP networks, ensuring that
user traffic immediately and transparently recovers from first-hop failures in network edge devices or
access circuits?
A. STP
B. IRDP TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
C. ICMP
D. HSRP
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 136
In which three HSRP states do routers send hello messages? (Choose three.)
A. standby
B. learn
C. listen
D. speak E. active
Correct Answer: ADE Section: (none) Explanation
Explanation/Reference:
QUESTION 137
Which protocol enables a group of routers to form a single virtual router and use the real IP address of
a router as the gateway address?
A. Proxy ARP
B. HSRP
C. IRDP
D. VRRP
E. GLBP
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 138
Which protocol inserts a four byte tag into the Ethernet frame and recalculates CRC value?
A. VTP
B. 802.1Q
C. DTP
D. ISL
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 139
What is the cause of jitter?
A. variable queue delays TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
B. packet drops
C. transmitting too many small packets
D. compression
Correct Answer: A Section: (none) Explanation
Explanation/Reference: QUESTION 140
The original frame is encapsulated and an additional header is added before the frame is carried over
a trunk link. At the receiving end, the header is removed and the frame is forwarded to the assigned VLAN.
This describes which technology?
A. DISL
B. DTP
C. IEEE 802.1Q
D. ISL
E. MPLS
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 141
On a multilayer Catalyst switch, which interface command is used to convert a Layer 3 interface to a
Layer 2 interface?
A. switchport
B. no switchport
C. switchport mode access
D. swithport access vlan vlan-id
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 142
Which two statements concerning STP state changes are true? (Choose two.)
A. Upon bootup, a port transitions from blocking to forwarding because it assumes itself as root.
B. Upon bootup, a port transitions from blocking to listening because it assumes itself as root.
C. Upon bootup, a port transitions from listening to forwarding because it assumes itself as root.
D. If a forwarding port receives no BPDUs by the max_age time limit, it will transition to listening.
E. If a forwarding port receives an inferior BPDU, it will transition to listening.
F. If a blocked port receives no BPDUs by the max_age time limit, it will transition to listening. TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
Correct Answer: BF Section: (none) Explanation
Explanation/Reference:
QUESTION 143
How does 802.1q trunking keep track of multiple VLAN’s?
A. modifies the port index of a data frame to indicate the VLAN
B. adds a new header containing the VLAN ID to the data frame
C. encapsulates the data frame with a new header and frame check sequence
D. tags the data frame with VLAN information and recalculates the CRC value
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 144
Given the above partial configuration, which two statements are true about VLAN traffic? (Choose two.)
A. VLANs 1-5 will be blocked if fa0/10 goes down.
B. VLANs 1-5 will use fa0/10 as a backup only.
C. VLANs 6-10 will use fa0/10 as a backup only.
D. VLANs 6-10 have a port priority of 128 on fa0/10.
E. VLANs 1-10 are configured to load share between fa0/10 and fa0/12.
Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 145
Given the above diagram and assuming that STP is enabled on all switch devices, which two
statements are true? (Choose two.)
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
A. DSW11 will be elected the root bridge.
B. DSW12 will be elected the root bridge.
C. ASW13 will be elected the root bridge.
D. P3/1 will be elected the nondesignated port.
E. P2/2 will be elected the nondesignated port.
F. P3/2 will be elected the nondesignated port.
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 146
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge. Which switch should the administrator configure as the root bridge and which configuration command must the administrator enter to accomplish this?
A. DSW11(config)# spanning-tree vlan 1 priority 4096
B. DSW12(config)# set spanning-tree priority 4096
C. ASW13(config)# spanning-tree vlan 1 priority 4096
D. DSW11(config)# set spanning-tree priority 4096 TestInside Help You Pass Any IT Exam http://www.TestInside.com
Testinside
E. DSW12(config)# spanning-tree vlan 1 priority 4096
F. ASW13(config)# set spanning-tree priority 4096
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 147
On a 3550 EMI switch, which three types of interfaces can be used to configure HSRP? (Choose three.)
A. loopback interface
B. SVI interface
C. routed port
D. access port
E. EtherChannel port channel
F. BVI interface
Correct Answer: BCE Section: (none) Explanation
Explanation/Reference:
QUESTION 148
Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on External_B fails?
A. standby 1 preempt
B. standby 1 track 10.10.10.1 TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
C. standby 1 priority 130
D. standby 1 track fastethernet 0/0
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 149
Examine the router output above. Which two items are correct? (Choose two.)
A. Router A will assume the active state if its priority is the highest.
B. If Ethernet 0/2 goes down, the standby router will take over.
C. When Ethernet 0/3 of RouterA comes back up, the priority will become 105.
D. The local IP address of Router A is 10.1.0.6.
E. The local IP address of Router A is 10.1.0.20.
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 150
Which router redundancy protocol cannot be configured for interface tracking?
A. HSRP
B. GLBP
C. VRRP
D. SLB
E. RPR
F. RPR+
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 151
Based on the show spanning-tree vlan 200 output shown in the exhibit, which two statements about
the STP process for VLAN 200 are true? (Choose two.)
A. BPDUs will be sent out every two seconds.
B. The time spent in the listening state will be 30 seconds.
C. The time spent in the learning state will be 15 seconds.
D. The maximum length of time that the BPDU information will be saved is 30 seconds.
E. This switch is the root bridge for VLAN 200.
F. BPDUs will be sent out every 10 seconds.
Correct Answer: BF Section: (none) Explanation
Explanation/Reference:
QUESTION 152
Which two statements are true when the extended system ID feature is enabled? (Choose two.)
A. The BID is made up of the bridge priority value(two bytes) and bridge MAC address (six bytes).
B. The BID is made up of the bridge priority (four bits), the system ID (12 bits), and a bridge MAC address (48 bits).
C. The BID is made up of the system ID (six bytes) and bridge priority value (two bytes).
D. The system ID value is the VLAN ID (VID).
E. The system ID value is a unique MAC address allocated from a pool of MAC addresses assigned to the switch or module.
F. The system ID value is a hex number used to measure the preference of a bridge in the spanning-tree algorithm.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference:
TestInside Help You Pass Any IT Exam http://www.TestInside.com Testinside
QUESTION 153
What can be determined about the HSRP relationship from the displayed debug output?
A. The preempt feature is not enabled on the 172.16.11.111 router.
B. The nonpreempt feature is enabled on the 172.16.11.112 router.
C. Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 154
16.11.112.
A. Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router
Correct Answer: Section: (none) Explanation
Explanation/Reference: QUESTION 155
16.11.111.
A. The IP address 172.16.11.111 is the virtual HSRP router IP address.
B. The IP address 172.16.11.112 is the virtual HSRP router IP address.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
Cisco 642-812 Questions and Answers Products basically comprise of the simulated Cisco 642-812 exam questions AND their most correct answers,accompanied with a methodical elucidation of the HP HP5-H07D exam answers and the probable wrong answers.The extent to which Cisco 642-812 exam Questions and Answers Products cover their Cisco subject is so thorough,that once you are done with a Cisco product,passing the Cisco 642-812 exam in first attempt should be a piece of cake.
Flydumps 300-207 dumps with PDF + Premium VCE + VCE Simulator: http://www.flydumps.com/300-207.html
Cisco 642-812 Real Demo, Helpful Cisco 642-812 Exam Test Questions UP To 50% Off
Welcome to download the newest Pass4itsure 640-822 VCE dumps: https://www.pass4itsure.com/640-822.html
Through the Cisco 640-822 exam is not easy. Juniper select the appropriate Cisco 640-822 exam sample questions only guarantee of FLYDUMPS success. I heard our customers talking about research, but he did not to cram, but told me to go FLYDUMPS this site with many on Cisco 640-822 exam sample questions, FLYDUMPS can provide relevant research and practical experience in a wide range of foundation. FLYDUMPS always designs our materials for exams with one goal in mind – ease of use. Through our Cisco 640-822 exam sample questions, we give you a very comfortable environment to study for the exam. We let you know about every detail and also let you analyze your strong and weak Juniper areas. You can then sharpen your skills very quickly and concentrate more on your weaker topics.
QUESTION 86
One of the following attack is characterized by a flood of packets that are requesting a TCP connection to a server. Which is it?
A. brute force
B. Trojan horse
C. reconnaissance
D. denial of service
Correct Answer: D
QUESTION 87
Match the corresponding command and configuration task. (Not all options are used.)
1.
login password certways1
2.
enable password certways2
3.
enable secret certways4
4.
service password-encryption
5.
line vty 0 4 password certways5
6.
line console 0 password certways3
A. encrypt all clear text passwords II.protect access to the user mode prompt III.set privileged mode encrypted password IV.set password to allow Telnet connections
B. set privileged mode clear text password
C. I-4,II-3,III-5,IV-2,V-6
D. I-4,II-5,III-3,IV-2,V-6
E. I-4,II-6,III-3,IV-5,V-2
F. I-4,II-6,III-5,IV-3,V-2
Correct Answer: C
QUESTION 88
You need to create a security plan for the certways network. What should be part of a comprehensive network security plan?
A. Delay deployment of software patches and updates until their effect on end-user equipment is well known and widely reported.
B. Physically secure network equipment from potential access by unauthorized individuals.
C. Encourage users to use personal information in their passwords to minimize the likelihood of passwords being forgotten.
D. Allow users to develop their own approach to network security.
Correct Answer: B
QUESTION 89
Topic – Implement and verify WAN links.
Describe different methods for connecting to a WAN Configure and verify a basic WAN serial connection A.
B.
C.
D.
Correct Answer:
QUESTION 90
Two of the following statements correctly describe the following network. What are them? (Choose two.)
A. There are six broadcast domains in the network.
B. There are four broadcast domains in the network.
C. There are two broadcast domains in the network.
D. There are seven collision domains in the network.
Correct Answer: CD
QUESTION 91
You need to create a security plan for the certways network. What should be part of a comprehensive network security plan?
A. 64 Kbit/sec
B. 32 Kbit/sec
C. 512 Kbit/sec
D. 128 Kbit/sec
Correct Answer: C
QUESTION 92
Look at the following exhibit. You are a network administrator for certways. You are configuring P4S-R to connect to a non-Cisco network. Which two commands would be applied to the S0/0 WAN interface, but not to the Fa0/0 LAN interface? (Choose two.)
A. ip address
B. no shutdown
C. encapsulation ppp
D. authentication pap
Correct Answer: CD
QUESTION 93
Look at the following exhibit. You are a network administrator for certways.You want to make each connection that is identified by the numbers shown. What kind of cable should be used?
A. 1 – Ethernet crossover cable
2 – Ethernet straight-through cable
3 – fiber optic cable
4 – rollover cable
B. 1 – Ethernet straight-through cable 2 – Ethernet crossover cable 3 – serial cable 4 – rollover cable
C. 1 – Ethernet straight-through cable 2 – Ethernet straight-through cable 3 – serial cable 4 – rollover cable
D. 1 – Ethernet rollover cable 2 – Ethernet crossover cable 3 – serial cable 4 – null modem cable
Correct Answer: C
QUESTION 94
Which of the following are included WAN data link encapsulation types? (Choose two.)
A. DSL
B. T1
C. PPP
D. Frame Relay
Correct Answer: CD
QUESTION 95
Which item gives the correct relationship between WAN connection technology and the associated communication link type? 1.PSTN 2.ATM 3.Leased Line 4.Frame Relay
A. Point to Point II.Circuit Switched III.Packet Switched IV.Cell Switched
B. I-3;II-1;III-4;IV-2
C. I-3;II-2;III-1;IV-4
D. I-3;II-1;III-2;IV-4
E. I-3;II-2;III-4;IV-1
Correct Answer: A
QUESTION 96
Part of the certways WAN is shown below:
Two buildings on the Los Angeles campus of a small company must be connected to use Ethernet with a
bandwidth of at least 100 Mbps. The company is concerned about possible problems from voltage
potential differences between the two buildings. Which media type should be used for the connection?
A. coaxial cable
B. UTP cable
C. STP cable
D. fiber optic cable
Correct Answer: D QUESTION 97
For the following items, which signaling standard is in charge of managing the connection and maintaining status between the router and the local Frame Relay switch?
A. CIR
B. DLCI
C. FECN
D. LMI
Correct Answer: D QUESTION 98
John works as a network administrator. It is difficult for him to establish a serial link between a Cisco router
and a router from another vendor. Both routers are configured for HDLC encapsulation.
Which two options are correct about this configuration? (Choose two.)
A. The Cisco HDLC frame uses a proprietary “Type” field that may not be compatible with equipment of other vendors.
B. Usernames must be configured at both ends of the HDLC serial link
C. PPP encapsulation is recommended for serial links between equipment from multiple vendors.
D. HDLC requires a clock rate to be configured on the routers at both ends of the serial link.
Correct Answer: AC QUESTION 99
Which two characteristics belong to a Frame Relay point-to-point subinterface? (Choose two.)
A. requires the frame-relay map command
B. resolves NBMA split horizon issues
C. maps one IP subnet across multiple DLCIs
D. maps one IP subnet per DLCI
Correct Answer: BD QUESTION 100
Examine the following technologies, which one will you use when a router connected to a LAN has only one WAN interface, but multiple virtual circuits are needed?
A. DSL
B. ADSL
C. Cable
D. Frame Relay
Correct Answer: D QUESTION 101
Host P4S-F sends out an ARP request to begin communicating with the server. How do you think the devices in the topology will respond to this request?
A. Router P4S-SFX will forward the ARP request to the ILM router.
B. The P4S-ILM router will respond with the IP address of the WWW server.
C. Router P4S-SFX will respond with the MAC address of its Fa0/0 interface.
D. Switch P4S-SWB will block the request since the server is not on the LAN.
Correct Answer: C
QUESTION 102
As a network administrator, you will need to decide on the appropriate network devices to use. Which of the following correctly describes the roles of devices in a WAN? (Choose three)
A. A CSU/DSU terminates a digital local loop.
B. A CSU/DSU terminates an analog local loop.
C. A modem terminates a digital local loop.
D. A modem terminates an analog local loop.
E. A router is commonly considered a DTE device.
Correct Answer: ADE
QUESTION 103
The certways WAN connection is shown below:
Based on this diagram shown above, which two devices can be used to complete the connection between
the WAN router at the customer site and the service provider? (Choose two.)
A. multiplexer
B. ATM switch
C. CSU/DSU
D. modem
Correct Answer: CD
QUESTION 104
Topic – Describe the operation of data networks.
Describe the purpose and functions of various network devices Select the components required to meet a given network specification Use the OSI and TCP/IP models and their associated protocols to explain how data flows in a network Describe common networking applications including web applications Describe the purpose and basic operation of the protocols in the OSI and TCP models Describe the impact of applications (Voice Over IP and Video Over IP) on a network Interpret network diagrams Determine the path between two hosts across a network Describe the components required for network and Internet communications Identify and correct common network problems at layers 1, 2, 3 and 7 using a layered model approach Differentiate between LAN/WAN operation and features
A.
B.
C.
D.
Correct Answer:
QUESTION 105
Host P4S-F, which needs to build the packet, has received the ARP reply. Two of the following information will be placed in the header of the packet that leaves host P4S-F if host P4S-F is to communicate with the WWW server. What is it? (Choose two)
A. The source address will be the IP address of host P4S-F.
B. The destination address will be the IP address of the WWW server.
C. The destination address will be the IP address of interface Fa0/0 of router P4S-SFX.
D. The destination address will be the IP address of interface Fa0/0 of the P4S-ILM router.
Correct Answer: AB
QUESTION 106
As it is shown in the exhibit, two World Wide Web documents from the WWW server Host are displayed by P4S-F in two browser windows at the same time. How did the data find its way to the correct browser windows?
A. The browsers track the data by the URL.
B. TCP port numbers are used to direct the data to the correct application window.
C. The OSI application layer tracks the conversations and directs them to the correct brower.
D. The IP source addresses of the packets will be used to direct the data to the correct browser window.
Correct Answer: B
QUESTION 107
You work in a medium-sized company .The network performance of your company has slowed to the point that users are complaining. In order to resolve this problem, You are asked to determine what the users might be doing to cause the slowdown. Which two types of network services or applications most likely cause slowdown? (Choose two.)
A. social networking web sites
B. blogs and other online browsing
C. PC-based VoIP services
D. online video sites
Correct Answer: CD QUESTION 108
Before a workstation is able to exchange HTTP packets with a web server, what must occur?
A. An ICMP connection must be established between the workstation and its default gateway.
B. An ICMP connection must be established between the workstation and the web server.
C. A UDP connection must be established between the workstation and the web server.
D. A TCP connection must be established between the workstation and the web server.
Correct Answer: D QUESTION 109
Look at the following exhibit. Connection problems are reported in the internetwork. By the output from P4S-HostA, what is the problem indicated?
A. The routing on P4S-R2 is not functioning properly.
B. The gateway address of P4S-HostA is incorrect or not configured.
C. The Fa0/24 interface of P4S-S1 is down.
D. An access list is applied to an interface of P4S-R3.
Correct Answer: B
QUESTION 110
Choose from the following three that are found in a TCP header, but not in a UDP header? (Choose three.)
A. window size
B. destination port
C. sequence number
D. acknowledgment number
Correct Answer: ACD
QUESTION 111
Match the corresponding commands and functions. (Not all options are used.) 1.ping 10.0.0.1 2.ping 127.0.0.1 3.tracert 4.ipconfig/all 5.arp -a 6.telnet
A. displays PC network configuration
II. displays the list of routers on a path to a network destination III.tests VTY configuration
IV. tests TCP/IP protocol stack
B. displays IP to MAC address mappings on a Windows PC
C. I-4,II-3,III-6,IV-2,V-5
D. I-4,II-3,III-1,IV-6,V-5
E. I-4,II-3,III-6,IV-5,V-2
F. I-4,II-3,III-5,IV-6,V-2
Correct Answer: A
QUESTION 112
Choose from the following two advantages of Layer 2 Ethernet switches over hubs. (Choose two.)
A. filtering frames based on MAC addresses
B. increasing the size of broadcast domains
C. decreasing the number of collision domains
D. allowing simultaneous frame transmissions
Correct Answer: AD
QUESTION 113
Data is divided into smaller pieces for transmission when files are transferred between a host and an FTP server. After these pieces reach the destination host, they should be reassembled to reconstruct the original file. What is used for the reassembly of these pieces into the correct order?
A. the TTL in the IP header
B. the sequence number in the TCP header
C. the Start Frame Delimiter in the 802.3 Preamble
D. the frame check sequence in the Ethernet frame trailer
Correct Answer: B QUESTION 114
On the basis of the exhibit below. After adding host A to the network, Host A is unable to communicate on
the network. A ping issued on the host to address 127.0.0.1 fails.
What is the problem?
A. The remote host at 127.0.0.1 is unreachable.
B. The default gateway is incorrect.
C. The IP address of host A is incorrect.
D. The TCP/IP protocols are not loaded.
Correct Answer: D
QUESTION 115
Attaching an Ethernet cable to a PC NIC and then attaching to a switch port. The PC power is turned on and the switch port link LED becomes green. Which two conditions does the link light indicate? (Choose two.)
A. Layer 2 communication has been established between the PC and switch.
B. Traffic is being sent from the switch to the PC.
C. If flashing, the green LED indicates port speed of 100 Mb/s.
D. The Layer 1 media is functioning between the PC and switch.
Correct Answer: AD
Cisco 640-822 exam only advanced and equipped with much more features,it is also not internet dependent,once installed.It enables you to see Interconnecting Cisco Networking Devices in a simulated Cisco 640-822 exam environment.Working with Cisco 640-822 exam Interactive Testing Engine is like passing an actual Cisco 640-822 exam.
Pass4itsure 640-822 dumps with PDF + Premium VCE + VCE Simulator: https://www.pass4itsure.com/640-822.html
Cisco 640-822 Test Engine, Sale Latest Cisco 640-822 Actual Test Online Shop
Welcome to download the newest Pass4itsure c4040-226 VCE dumps: http://www.pass4itsure.com/c4040-226.html
The Cisco 700-701 exam is one of the most popular Juniper Certification exams. If you want to reach a professional or expert level in the IBM Certification career certification tracks, passing Cisco 700-701 exam is the first step. We provide professional Cisco 700-701 exam sample questions. Cisco 700-701 exam details Candidates can become IBM certified professionals by using a general Cisco 700-701 Certification test offered by FLYDUMPS. We all know that succeeding in Cisco 700-701 Exam is essential in the IT industry. Cisco 700-701 Certification is a world-widely recognized certification. In order to enhance your career value, it’s right to get Cisco 700-701 certification. We devise FLYDUMPS Cisco 700-701 exam sample questions containing various 108 questions in a way that could help you ace the exam without any other books or materials.
QUESTION 1
What is a Cisco Application Policy Infrastructure Controller?
A. A Cisco ACI fabric controller with open API
B. A third-party SDN controller that is compatible with all data center switches
C. A controller module in the Nexus 9500 Switch
D. A virtual application development environment Correct Answer: A
Explanation Explanation/Reference:
Reference: http://www.cisco.com/c/dam/en/us/products/collateral/cloud-systems- management/aci-fabric-controller/at-a-glance-c45-730001.pdf
QUESTION 2
Which statement about the Cisco APIC is true?
A. It stores policies.
B. It provides a physical connectivity port to a legacy network
C. It provides a test environment for applications.
D. It stores the storage network profile. Correct Answer: A
Explanation Explanation/Reference:
Reference: http://www.cisco.com/c/en/us/solutions/collateral/data-center-virtualization/unified- fabric/white-paper-c11-730021.html (first para)
QUESTION 3
What is driving customer interests in SDN?
A. Return on investment
B. Programmability/ automation
C. Application bandwidth
D. Security compliance
E. Big data analytics Correct Answer: B
Explanation Explanation/Reference:
QUESTION 4
Which customer requirement is addressed by an ACI solution?
A. Storage consolidation
B. Multi-hypervisor environments
C. Database performance improvement
D. Big data analytics Correct Answer: B
Explanation Explanation/Reference:
Reference: http://www.cisco.com/c/en/us/solutions/collateral/data-center-virtualization/unified- fabric/ solution-brief-c22-729866.html (challenges, second para)
QUESTION 5
Which statement about the Cisco APIC is true?
A. It provides the application health score.
B. It provides a physical connectivity port to a legacy network
C. It stores the storage network profile.
D. It provides a test environment for applications.
Correct Answer: A Explanation
Explanation/Reference:
Explanation:
APIC Features and Capabilities
Centralized application-level policy engine for physical, virtual, and cloud infrastructures ·Detailed
visibility, telemetry, and health scores by application and by tenant
Designed around open standards and open APIs
Robust implementation of multi-tenant security, quality of service (QoS), and high availability
Integration with management systems such as VMware, Microsoft, and OpenStack Reference: http://www.cisco.com/c/en/us/products/cloud-systems-management/application-policy- infrastructure-controller-apic/index.html
QUESTION 6
How many I/O module slots are available in the Cisco Nexus 9504 Switch?
A. 4 slots
B. 3 slots
C. 2 slots
D. 1 slot
Correct Answer: A Explanation
Explanation/Reference:
Reference: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/hw/n9504_hig/b_n9504_h ardware_install_guide/b_n9504_hardware_install_guide_chapter_01.html (see the first table on the page, second row, first column)
QUESTION 7
What is a Cisco Nexus 9500 Series Switch?
A. An all-in-one SDN solution
B. A modular switch
C. A fixed top-of-rack switch
D. A virtual software switch
Correct Answer: B Explanation
Explanation/Reference:
Reference: http://www.cisco.com/c/en/us/products/collateral/switches/nexus-9000-series- switches/white-paper-c11-729987.html (see the first paragraph on the page)
QUESTION 8
Which two switch port count options are available on the Cisco Nexus 9300 Series Switch? (Choose two.)
A. 96 ports
B. 48 ports
C. 24 ports
D. 72 ports
E. 128 ports
Correct Answer: AB Explanation
Explanation/Reference:
Reference: http://www.cisco.com/c/en/us/products/collateral/switches/nexus-9000-series- switches/ datasheet-c78-729405.html (see table 1)
QUESTION 9
Which customer initiative often leads to an ACI sales opportunity?
A. Storage consolidation
B. Network replacement or upgrade
C. Business process outsourcing
D. Security assessment
Correct Answer: B Explanation
Explanation/Reference:
QUESTION 10
Which two data center use cases are often drivers for an SDN solution? (Choose two.)
A. Mainframe terminals
B. Secure multi-tenancy
C. BYOD
D. Applications
E. Guest wireless access
Correct Answer: CD Explanation
Explanation/Reference:
QUESTION 11
Which two options are the two ACI solution components? (Choose two.)
A. Cisco Cloud Services Router 1000V
B. Cisco Nexus 9000 Switches
C. Spine Leaf architecture
D. Cisco Application Policy Infrastructure Controller
E. Cisco Unified Computing System B-Series Servers
Correct Answer: BD Explanation
Explanation/Reference:
Reference: http://www.cisco.com/c/dam/en/us/products/collateral/cloud-systems- management/aci-fabric-controller/at-a-glance-c45-729864.pdf (page 2)
Cisco 700-701 is the composite exam associated with the Cisco Certified Network Associate certification.Candidates can prepare for this Cisco 700-701 exam.This Cisco 700-701 exam tests a candidate’s knowledge and skills required to install, operate, and troubleshoot a small to medium size enterprise branch network.
Pass4itsure c4040-226 dumps with PDF + Premium VCE + VCE Simulator: http://www.pass4itsure.com/c4040-226.html
Cisco 700-701 Real Exam Questions And Answers, Provides Cisco 700-701 Exam Dumps Guaranteed Success