Flydumps Cisco 642-901 exam questions and answers in PDF are prepared by our expert, Moreover, they are based on the recommended syllabus covering all the Cisco 642-901 exam objectives.You will find them to be very helpful and precise in the subject matter since all the Cisco 642-901 exam content is regularly updated and has been checked for accuracy by our team of SAP expert professionals.
QUESTION 110
Refer to the exhibit. Routers R1 and R2 are IPv6 BGP peers that have been configured to support a neighbor relationship over an IPv4 internetwork. Which three neighbor IP addresses are valid choices to use in the highlighted section of the exhibit? (Choose three.)
A. ::0A43:0002
B. 0A43:0002::
C. ::10.67.0.2
D. 10.67.0.2::
E. 0:0:0:0:0:0:10.67.0.2
F. 10.67.0.2:0:0:0:0:0:0
Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:
QUESTION 111
Refer to the exhibit. BGP has been configured on the routers in the network.
However, the IBGP peers in autonomous system 65200 have not converged. In addition, this console
message was generated on router R2:
*Mar 1 03:09:07.729: %TCP-6-BADAUTH No MD5 digest from 10.10.23.2(179) to 10.10.23.3(11002)
On the basis of the information that is provided, what is the cause of the problem?
A. BGP authentication can be used on eBGP peers only.
B. The password that is used for BGP authentication on both BGP peers in autonomous system 65200 must be the same.
C. BGP authentication can be used on iBGP peers when the connection is configured between the loopback interfaces.
D. OSPF must be configured with the same MD5 authentication.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 112
Refer to the exhibit diagram and configuration. RTB is summarizing its networks from AS 64100 with the aggregate-address command. However, the show ip route command on RTA reveals the RTB individual networks as well as its summary route. Which option would ensure that only the summary route would appear in the routing table of RTA?
A. Delete the four network statements and leave only the aggregate-address statement in the BGP configuration.
B. Add the keyword summary-only to the aggregate-address command.
C. Add a static route with a prefix of 192.168.24.0 255.255.252.0 pointing to the null0 interface.
D. Create a route map permitting only the summary address.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 113
Router RTA is configured as follows:
RTA (config)#router rip RTA(config-router)#network 10.0.0.0 RTA(config-router)#distribute-list 44 in interface BRI0 RTA(config-router)#exit RTA(config)#access-list 44 deny 172.16.1.0 0.0.0.255 RTA(config)#access-list 44 permit any
What are the effects of this RIP configuration on router RTA? (Choose two.)
A. no routing updates will be sent from router RTA on interface BRI0 to router RTX
B. router RTA will not advertise the 10.0.0.0 network to router RTX
C. the route to network 172.16.1.0 will not be entered into the routing table on router RTA
D. user traffic from the 172.16.1.0 network is denied by access-list 44
E. the routing table on router RTA will be updated with the route to router RTW
Correct Answer: CE Section: (none) Explanation
Explanation/Reference:
QUESTION 114
During the redistribution process configured on RTA, some of the EIGRP routes, such as 10.1.1.0/24 and 10.2.2.0/24, are not being redistributed into the OSPF routing domain.
Which two items could be a solution to this problem? (Choose two.)
A. Change the metric-type to 2 in the redistribute command.
B. Configure the redistribute command under router eigrp 1 instead.
C. Change the EIGRP AS number from 100 to 1 in the redistribute command.
D. Add the subnets option to the redistribute command.
E. Change the metric to an EIGRP compatible metric value (bandwidth, delay, reliability, load, MTUs) in the redistribute command.
Correct Answer: CD Section: (none) Explanation
Explanation/Reference:
QUESTION 115
Which IS-IS router is equivalent to an ABR in OSPF?
A. Level 0
B. Level 1
C. Level 2
D. Level 3
E. Level 1-2
F. Level 2-3
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 116
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 receive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task?
A. R1(config)# router eigrp 1 R1(config-router)# passive-interface serial 0
B. R2(config)# router eigrp 1 R2(config-router)# passive-interface serial 0
C. R1(config)# access-list 20 deny any R1(config)# router eigrp 1 R1(config-router)# distribute-list 20 out serial 0
D. R2(config)# access-list 20 deny any R2(config)# router eigrp 1 R2(config-router)# distribute-list 20 out serial 0
E. R1(config)# access-list 20 permit any R1(config)# router eigrp 1 R1(config-router)# distribute-list 20 in serial 0
F. R2(config)# access-list 20 permit any R2(config)# router eigrp 1 R2(config-router)# distribute-list 20 in serial 0
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 117
Hotspot
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 118
Refer to the exhibit. Given the exhibited router output, which command sequence can be added to R1 to generate a default route into the OSPF domain?
A. default-router
B. ip default-network
C. default-information originate always
D. ip default-gateway
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 119
Refer to the exhibit. During the process of configuring a virtual link to connect area 2 with the backbone area, the network administrator received this console message on R3:
*Mar 1 00:25:01.084: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual link but not found from 20.20.20.1, Serial 0
How should the virtual link be configured on the OSPF routers to establish full connectivity between the areas?
A. R1(config-router)# area 1 virtual-link 30.30.30.3 R3(config-router)# area 1 virtual-link 20.20.20.1
B. R1(config-router)# area 1 virtual-link 20.20.20.2 R3(config-router)# area 1 virtual-link 30.30.30.2
C. R1(config-router)# area 0 virtual-link 1.1.1.1 R3(config-router)# area 2 virtual-link 3.3.3.3
D. R1(config-router)# area 1 virtual-link 3.3.3.3 R3(config-router)# area 1 virtual-link 1.1.1.1
E. R1(config-router)# area 1 virtual-link 2.2.2.2 R3(config-router)# area 1 virtual-link 2.2.2.2
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 120
LAB
A. Portland# conf t Portland(config)# router ospf 1 Portland(config-router)# network 192.168.5.4 0.0.0.3 area 1 Portland(config-router)# area 1 stub Portland(config-router)# end Portland# copy run start Indianapolis# conf t Indianapolis(config)# router ospf 1 Indianapolis(config-router)# network 192.168.5.4 0.0.0.3 area 1 Indianapolis(config-router)# area 1 stub no-summary Indianapolis(config-router)# end Indianapolis# copy run start
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 121
The command bgp always-compare-med is added to a router configuration.
What will this command accomplish?
A. forces the router to compare metrics of routes from different autonomous systems
B. forces the router to compare the local preference of routes from different autonomous systems
C. forces the router to compare the weight of routes from different autonomous systems
D. forces the router to compare the communities of routes from different autonomous systems
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 122
An administrator is redistributing OSPF into RIP. RIP is routing the 128.103.36.0/24 network. OSPF is routing the 128.103.35.32/28 network. Users in the RIP domain cannot reach devices in the OSPF domain. Which two tasks must be done to enable RIP to advertise the routes learned from OSPF into the RIP domain? (Choose two.)
A. Add a static route that points to the RIP domain address space with a /24 network mask and a next hop of 128.103.36.2.
B. Add a static route that points to the OSPF domain address space with a /24 network mask with a next hop of null0.
C. Tune the OSPF default metrics to allow seamless redistribution into RIP.
D. Redistribute configured static routes into RIP.
E. Use a route map statement inserted into a distribute list to control routing updates.
Correct Answer: BD Section: (none) Explanation
Explanation/Reference: QUESTION 123
Which two provide intra-area routing services? (Choose two.)
A. L1 IS
B. L1 ES
C. L2 IS
D. L2 ES
E. L1/L2 IS
Correct Answer: AE Section: (none) Explanation
Explanation/Reference:
QUESTION 124
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the function of rendezvous point (RP) for the multicast network?
A. router R1
B. router R2
C. both routers R1 and R2
D. none of the routers since they are not configured with static RP
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 125
Refer to the exhibit. Which two statements are true about the partial configuration that is shown? (Choose two.)
A. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address 10.0.0.6.
B. The first DHCP client to connect to the FastEthernet 0/1 interface will receive the IP address 10.10.0.1.
C. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address 10.0.0.1
D. Hosts connected to the FastEthernet0/1 interface will not receive DHCP replies from the router.
E. DHCP requests received on the FastEthernet 0/1 interface will be forwarded to 10.0.0.2.
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 126
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 receive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task?
A. R1(config)# router eigrp 1 R1(config-router)# passive-interface serial 0
B. R2(config)# router eigrp 1 R2(config-router)# passive-interface serial 0
C. R1(config)# access-list 20 deny any R1(config)# router eigrp 1 R1(config-router)# distribute-list 20 out serial 0
D. R2(config)# access-list 20 deny any R2(config)# router eigrp 1 R2(config-router)# distribute-list 20 out serial 0
E. R1(config)# access-list 20 permit any R1(config)# router eigrp 1 R1(config-router)# distribute-list 20 in serial 0
F. R2(config)# access-list 20 permit any R2(config)# router eigrp 1 R2(config-router)# distribute-list 20 in serial 0
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 127
Hotspot
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
QUESTION 128
Refer to the exhibit. EIGRP is enabled on all routers on the network. What additional configuration is required for the routers connected over the Frame Relay multipoint interfaces to compensate for a low-speed NBMA connection?
A. Configure the EIGRP hello interval on all Frame Relay interfaces to 5 seconds.
B. Configure the EIGRP hello interval on all Frame Relay interfaces to 60 seconds.
C. Configure the EIGRP hold time on all Frame Relay interfaces to 15 seconds.
D. Configure the EIGRP hold time on all Frame Relay interfaces to 180 seconds.
E. Configure the bandwidth on all EIGRP Frame Relay interfaces to the committed information rate (CIR).
F. Configure the bandwidth on all EIGRP Frame Relay interfaces to the lowest CIR multiplied by the number of PVCs for the multipoint connection.
Correct Answer: F Section: (none) Explanation
Explanation/Reference:
QUESTION 129
Which show command will display the two values used in the calculation of the EIGRP metric?
A. show protocol
B. show ip eigrp interface
C. show interface
D. show ip eigrp neighbor
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 130
Which three restrictions apply to OSPF stub areas? (Choose three.)
A. No virtual links are allowed.
B. The area cannot be a backbone area.
C. Redistribution is not allowed unless the packet is changed to a type 7 packet.
D. The area has no more than 10 routers.
E. No autonomous system border routers are allowed.
F. Interarea routes are suppressed.
Correct Answer: ABE Section: (none) Explanation
Explanation/Reference:
QUESTION 131
Refer to the exhibit. IP multicast configuration changes have been made on several routers. However, the IP multicast table displayed in the exhibit still does not reflect the changes.
What should be done to display the new routing table information?
A. Issue the no ip mroute-cache privileged EXEC command.
B. Issue the clear ip igmp group privileged EXEC command.
C. Issue the clear ip mroute privileged EXEC command.
D. Issue the clear ip route * privileged EXEC command.
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 132
Identify three characteristics of EIGRP feasible successors? (Choose three.)
A. A feasible successor is selected by comparing the advertised distance of a non-successor route to the feasible distance of the best route.
B. If the advertised distance of the non-successor route is less than the feasible distance of best route, then that route is identified as a feasible successor.
C. If the successor becomes unavailable, then the feasible successor can be used immediately without recalculating for a lost route.
D. The feasible successor can be found in the routing table.
E. Traffic will be load balanced between feasible successors with the same advertised distance.
Correct Answer: ABC Section: (none) Explanation
Explanation/Reference: QUESTION 133
What are three kinds of OSPF areas? (Choose three.)
A. stub
B. active
C. remote
D. backbone
E. ordinary or standard
Correct Answer: ADE Section: (none) Explanation
Explanation/Reference:
QUESTION 134
Based on the show ip bgp summary output, which two statements are true? (Choose two.)
A. The BGP session to the 10.1.1.1 neighbor is established.
B. The BGP session to the 10.2.2.2 neighbor is established.
C. The BGP session to the 10.3.3.3 neighbor is established.
D. The router is attempting to establish a BGP peering session with the 10.1.1.1 neighbor.
E. The BGP session to the 10.3.3.3 neighbor is established, but the router has not received any BGP routing updates from the 10.3.3.3 neighbor.
F. The router is attempting to establish a BGP peering session with the 10.2.2.2 neighbor.
Correct Answer: AF Section: (none) Explanation
Explanation/Reference:
Preparing Cisco 642-901 exam is not difficult now.You can prepare from Cisco 642-901 Certification or Cisco 642-901 dumps.Here we have mentioned some sample questions.You can use our Cisco 642-901 study material notes for test preparation. Latest Cisco 642-901 study material available.
You can prepare for Cisco 642-901 with little effort because Flydumps is now at your service to act as a guide in Flydumps you pass Cisco 642-901 exam. Now get that necessary competitive edge that comes with preparing with the help of Flydumps.
QUESTION 101
Which three statements are correct about the differences in IS-IS and OSPF? (Choose three.)
A. IS-IS LSP contains TLV fields and OSPF LSU contains the LSAs.
B. New additions to the protocol are easily implemented in OSPF but not with IS-IS.
C. For greater fine tuning there are more IS-IS timers.
D. OSPF has more area types than does IS-IS.
E. IS-IS is more CPU-intensive than is OSPF.
Correct Answer: ACD Section: Multiple Choice Questions Explanation
Explanation/Reference: QUESTION 102
What is the purpose of the eigrp stub configuration command?
A. to increase scalability by limiting the EIGRP query range
B. to reduce the size of the routing table by blocking the D EX (External EIGRP) routes into the EIGRP stub router
C. to reduce the convergence time by enabling the EIGRP stub router to propagate the EIGRP queries from the EIGRP hub router
D. to reduce the convergence time by enabling the EIGRP stub router to also perform query requests to the EIGRP hub router
Correct Answer: A Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 103
Which configuration commands will enable RTA to advertise all local interfaces over OSPF?
A. RTA(config)# router ospf 1RTA(config-router)# default-information originate
B. RTA(config)# router ospf 1RTA(config-router)# network 255.255.255.255 255.255.255.255
C. RTA(config)# router ospf 1RTA(config-router)# network 0.0.0.0
D. RTA(config)# router ospf 1RTA(config-router)# network 0.0.0.0 0.0.0.0
E. RTA(config)# router ospf 1RTA(config-router)# redistribute static
F. RTA(config)# router ospf 1RTA(config-router)# redistribute connected
Correct Answer: F Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 104
Which command lists the system IDs of all known IS-IS routers?
A. show clns neighbors
B. show isis database
C. show isis topology
D. show clns neighbors detail
E. show is-is neighbors detail
Correct Answer: C Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 105
Refer to the exhibit. Which two statements are true? (Choose two.)
A. The eigrp stub command prevents queries from being sent from R2 to R1.
B. The eigrp stub command will automatically enable summarization of routes on R2.
C. The eigrp stub command prevents all routes except a default route from being advertised to R1.
D. Router R1 will advertise connected and summary routes only.
E. Router R1 will advertise connected and static routes. The sending of summary routes will not be permitted.
F. Router R1 is configured as a receive-only neighbor and will not send any connected, static, or summary routes.
Correct Answer: AD Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 106
A network administrator would like to configure an EIGRP router as a stub router that advertises directly connected and summary routes only. What command must the administrator issue to accomplish this?
A. eigrp stub
B. eigrp stub connected
C. eigrp stub summary
D. eigrp stub connected static
E. eigrp stub receive-only
Correct Answer: A Section: Multiple Choice Questions Explanation Explanation/Reference:
QUESTION 107
Refer to the exhibit diagram and configuration. RTB is summarizing its networks from AS 64100 with the aggregate-address command. However, the show ip route command on RTA reveals the RTB individual networks as well as its summary route. Which option would ensure that only the summary route would appear in the routing table of RTA?
A. Delete the four network statements and leave only the aggregate-address statement in the BGP configuration.
B. Add the keyword summary-only to the aggregate-address command.
C. Add a static route with a prefix of 192.168.24.0 255.255.252.0 pointing to the null0 interface.
D. Create a route map permitting only the summary address.
Correct Answer: B Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 108
How is the designated querier elected in IGMPv2?
A. The first router to appear on a subnet is designated.
B. The host that responds first to the election query is designated.
C. The router with the lowest IP address on a subnet is designated.
D. The host with the lowest MAC address on a segment is designated.
Correct Answer: C Section: Multiple Choice Questions Explanation
Explanation/Reference: QUESTION 109
Which type of IGMP message is sent when a network client wants to join a multicast group?
A. host membership query
B. host membership report
C. host membership status
D. host membership notification
Correct Answer: B Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 110
When an IPv6 enabled host boots, it sends a router solicitation (RS) message. An IPv6 router responds with a router advertisement (RA). Which two items are contained in the RA? (Choose two.)
A. IPv6 address for the host
B. lifetime of the prefix
C. prefixes for the link
D. keepalive timers
E. request for the local host IP address
F. any route advertisements it has received
Correct Answer: BC Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 111
Which statement is true concerning 6to4 tunneling?
A. IPv4 traffic is encapsulated with an IPv6 header.
B. The edge routers can use any locally configured IPv6 address.
C. Hosts and routers inside a 6to4 site will need a special code.
D. An edge router must use IPv6 address of 2002::/16 in its prefix.
Correct Answer: D Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 112
Observe the exhibit. If the command variance 3 were added to RTE, which path or paths would be chosen to route traffic to network X?
A. E-B-A
B. E-B-A and E-C-A
C. E-C-A and E-D-A
D. E-B-A, E-C-A and E-D-A
Correct Answer: B Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 113
Refer to the exhibit. What happens when the router stops receiving advertisements for the 10.1.2.0/24 network?
A. The summary route will be removed from the table.
B. The summary route will remain in the table.
C. The more specific routes will be advertised from the table.
D. 10.1.2.0/24 will still be advertised but packets destined for it will be dropped when they reach this router.
Correct Answer: B Section: Multiple Choice Questions
Explanation Explanation/Reference:
QUESTION 114
Which statement is true about EBGP?
A. An internal routing protocol can be used to reach an EBGP neighbor.
B. The next hop does not change when BGP updates are exchanged between EBGP neighbors.
C. A static route can be used to form an adjacency between neighbors.
D. EBGP requires a full mesh.
Correct Answer: C Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 115
Refer to the exhibit. What is the effect of the distribute-list command in the R1 configuration?
A. R1 will filter only the 172.24.1.0/24 route from the R2 RIP updates.
B. R1 will permit only the 10.0.0.0/24 route in the R2 RIP updates.
C. R1 will filter the 10.1.0.0/24 and the 172.24.1.0/24 routes from the R2 RIP updates.
D. R1 will not filter any routes because there is no exact prefix match.
Correct Answer: C Section: Multiple Choice Questions Explanation
Explanation/Reference:
QUESTION 116
Based on the information in the exhibit, which statement is true?
A. RTC will be able to access the 10.0.0.0 network.
B. RTC will not have the 10.0.0.0 network in its routing table.
C. RTC will not have the 192.168.10.0 network in its routing table.
D. RTB will not have the 10.0.0.0 network in its routing table.
E. RTB and RTC will not have the 10.0.0.0 network in their routing tables.
Correct Answer: B Section: Multiple Choice Questions Explanation
Explanation/Reference:
Well-regarded for its level of detail, assessment features, and challenging review questions and hands-on exercises, Cisco 642-901 helps you master the concepts and techniques that will enable you to succeed on the Cisco 642-901 exam the first time.
Flydumps bring you the best Cisco 642-618 exam preparation materials which will make you pass in the first attempt.And we also provide you all the Cisco 642-618 exam updates as Flydumps announces a change in its Cisco 642-618 exam syllabus,we inform you about it without delay.
QUESTION 87
Which two configurations are required on the Cisco ASAs so that the return traffic from the
10.10.10.100 outside server back to the 10.20.10.100 inside client can be rerouted from the Active Ctx B context in ASA Two to the Active Ctx A context in ASA One? (Choose two.)
A. stateful active/active failover
B. dynamic routing (EIGRP or OSPF or RIP)
C. ASR-group
D. no NAT-control
E. policy-based routing
F. TCP/UDP connections replication
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 88
Which two statements about the class maps are true? (Choose two.)
A. These class maps are referenced within the global policy by default for HTTP inspection.
B. These class maps are all type inspect http class maps.
C. These class maps classify traffic using regular expressions.
D. These class maps are Layer 3/4 class maps.
E. These class maps are used within the inspection_default class map for matching the default inspection traffic.
Correct Answer: BC Section: (none) Explanation
Explanation/Reference:
QUESTION 89
Which three Cisco ASA configuration commands are used to enable the Cisco ASA to log only the debug output to syslog? (Choose three.)
A. logging list test message 711001
B. logging debug-trace
C. logging trap debugging
D. logging message 711001 level 7
E. logging trap test
Correct Answer: ABE Section: (none) Explanation
Explanation/Reference:
QUESTION 90
Which five options are valid logging destinations for the Cisco ASA? (Choose five.)
A. AAA server
B. Cisco ASDM
C. buffer
D. SNMP traps
E. LDAP server
F. email
G. TCP-based secure syslog server
Correct Answer: BCDFG Section: (none) Explanation
Explanation/Reference:
QUESTION 91
When configuring security contexts on the Cisco ASA, which three resource class limits can be set using a rate limit? (Choose three.)
A. address translation rate
B. Cisco ASDM session rate
C. connections rate
D. MAC-address learning rate (when in transparent mode)
E. syslog messages rate
F. stateful packet inspections rate
Correct Answer: CEF Section: (none) Explanation
Explanation/Reference:
QUESTION 92
Which two statements about Cisco ASA redundant interface configuration are true? (Choose two.)
A. Each redundant interface can have up to four physical interfaces as its member.
B. When the standby interface becomes active, the Cisco ASA sends gratuitous ARP out on the standby interface.
C. Interface duplex and speed configurations are configured under the redundant interface.
D. Redundant interfaces use MAC address-based load balancing to load share traffic across multiple physical interfaces.
E. Each Cisco ASA supports up to eight redundant interfaces.
Correct Answer: BE Section: (none) Explanation
Explanation/Reference:
QUESTION 93
The Cisco ASA must support dynamic routing and terminating VPN traffic. Which three Cisco ASA options will not support these requirements? (Choose three.)
A. transparent mode
B. multiple context mode
C. active/standby failover mode
D. active/active failover mode
E. routed mode
F. no NAT-control
Correct Answer: ABD Section: (none) Explanation
Explanation/Reference:
QUESTION 94
Which two functions will the Set ASDM Defined User Roles perform? (Choose two.)
A. enables role based privilege levels to most Cisco ASA commands
B. enables the Cisco ASDM user to assign privilege levels manually to individual commands or groups of commands
C. enables command authorization with a remote TACACS+ server
D. enables three predefined user account privileges (Admin=Priv 15, Read Only=Priv 5, Monitor Only=Priv 3)
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 95
Which two statements about Cisco ASA failover troubleshooting are true? (Choose two.)
A. With active/active failover, failover link troubleshooting should be done in the system execution space.
B. With active/active failover, ASR groups must be enabled.
C. With active/active failover, user data passing interfaces troubleshooting should be done within the context execution space.
D. The failed interface threshold is set to 1. Using the show monitor-interfacecommand, if one of the monitored interfaces on both the primary and secondary Cisco ASA appliances is in the unknown state, a failover should occur.
E. Syslog level 1 messages will be generated on the standby unit only if the logging standbycommand is used.
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 96
When troubleshooting a Cisco ASA that is operating in multiple context mode, which two verification steps should be performed if a user context does not pass user traffic? (Choose two.)
A. Verify the interface status in the system execution space.
B. Verify the mac-address-table on the Cisco ASA.
C. Verify that unique MAC addresses are configured if the contexts are using nonshared interfaces.
D. Verify the interface status in the user context.
E. Verify the resource classes configuration by accessing the admin context.
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 97
On Cisco ASA Software Version 8.3 and later, which two sets of CLI configuration commands result from this Cisco ASDM configuration? (Choose two.)
A. nat (inside) 1 10.1.1.10 global (outside) 1 192.168.1.1
B. nat (outside) 1 192.168.1.1 global (inside 1 10.1.1.10
C. static(inside,outside) 192.168.1.1 10.1.1.10 netmask 255.255.255.255 tcp 0 0 udp 0
D. static(inside,outside) tcp 192.168.1.1 80 10.1.1.10 80
E. object network 192.168.1.1 nat (inside,outside) static 10.1.1.10
F. object network 10.1.1.10 nat (inside,outside) static 192.168.1.1
G. access-list outside_access_in line 1 extended permit tcp any object 10.1.1.10 eq http access-group outside_access_in in interface outside
H. access-list outside_access_in line 1 extended permit tcp any object 192.168.1.1 eq http access-group outside_access_in in interface outside
Correct Answer: FG Section: (none) Explanation
Explanation/Reference:
QUESTION 98
On the Cisco ASA Software Version 8.4.1, which three parameters can be configured using the set connection command within a policy map? (Choose three.)
A. per-client TCP and/or UDP idle timeout
B. per-client TCP and/or UDP maximum session time
C. TCP sequence number randomization
D. maximum number of simultaneous embryonic connections
E. maximum number of simultaneous TCP and/or UDP connections
F. fragments reassembly options
Correct Answer: CDE Section: (none) Explanation
Explanation/Reference:
QUESTION 99
On Cisco ASA Software Version 8.4.1, which four inspections are enabled by default in the global policy? (Choose four.)
A. HTTP
B. ESMTP
C. SKINNY
D. ICMP
E. TFTP
F. SIP
Correct Answer: BCEF Section: (none) Explanation
Explanation/Reference:
QUESTION 100
Which two statements about traffic shaping capability on the Cisco ASA appliance are true? (Choose two.)
A. Traffic shaping can be applied to all outgoing traffic on a physical interface or, in the case of the Cisco ASA 5505 appliance, on a VLAN.
B. Traffic shaping can be applied in the input or output direction.
C. Traffic shaping can cause jitter and delay.
D. You can configure traffic shaping and priority queuing on the same interface.
E. With traffic shaping, when traffic exceeds the maximum rate, the security appliance drops the excess traffic.
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
Cisco 642-618 Questions & Answers covers all the knowledge points of the real exam. We update our product frequently so our customer can always have the latest version of Cisco 642-618. We provide our customers with the excellent 7×24 hours customer service.We have the most professional Cisco 642-618 expert team to back up our grate quality products.If you still cannot make your decision on purchasing our product, please try our Cisco 642-618 free pdf